FOCUS Enhancements FS-2E, FS-2 User Manual
FS-2/2E Studio DTE
Disk Recorder
User Guide
MANL-0927-04
Symbols
In the FS-2/2E Documentation
On the FS-2/2E Unit
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of an
uninsulated Dangerous Voltage within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of electric shock
to persons.
Caution
For continued protection against fire, replace only with fuses of
correct rating, as listed on the rear panel.
Caution
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the device.
Notices: Legal, Regulatory, and Safety
LEGAL NOTICES
THIS DOCUMENT CONTAINS CONFIDENTIAL AND TRADE SECRET
INFORMATION OF FOCUS ENHANCEMENTS AND ITS RECEIPT OR
POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE OR
DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE, OR SELL
ANYTHING THAT IT MAY DESCRIBE. REPRODUCING, DISCLOSING, OR
USING IN WHOLE OR IN PART WITHOUT THE SPECIFIC WRITTEN
AUTHORIZATION OF FOCUS ENHANCEMENTS IS STRICTLY FORBIDDEN.
EVERY EFFORT HAS BEEN MADE TO ENSURE THAT THE INFORMATION IN
THIS DOCUMENT IS COMPLETE AND ACCURATE AT THE TIME OF
PRINTING; HOWEVER, THE INFORMATION CONTAINED IN THIS
DOCUMENT IS SUBJECT TO CHANGE.
Copyright
Copyright 2006 FOCUS ENHANCEMENTS
All Rights Reserved
The material contained in this document is also protected by copyright laws of the
United States of America and other countries. It may not be reproduced or
distributed in any form by any means, altered in any fashion, or stored in a data
base or retrieval system, without express written permission of FOCUS
ENHANCEMENTS.
FOCUS ENHANCEMENTS is responsible for unauthorized use of equipment and
does not make allowance or credit for unauthorized use or access.
FS-2/2E Studio DTE Disk Recorder User Guide
iii
Contacting FOCUS ENHANCEMENTS
USA
Office Hours:
Email:
Telephone:
Fax:
Address:
EMEA (Europe, Middle East, Africa)
Office Hours:
Email:
Telephone:
Fax:
Address:
Monday through Friday
8:00 AM to 5:00PM (Central Time)
support@focusinfo.com
+1 763-398-1658
+1 763-571-7688
Focus Enhancements, Inc.
1370 Dell Avenue
Campbell, CA. 95008
www.focusinfo.com
Monday through Friday
9:00 AM to 5:00PM
techsupport@como.com
+49 4307 - 83 58 58
+49 4307 - 83 58 99
COMO Computer & Motion GmbHA
A Focus Enhancements Company
Lise-Meitner-Str. 15
24223 Raisdorf / Germany
www.focusinfo.com
Serial Number
The serial number for this equipment is located on the bottom of the unit. Please
write this serial number on the enclosed warranty card and keep it in a secure area.
Registering Products, Technical Support, and Warranty
To register a Focus Enhancements product use the online form at:
http://www.focusinfo.com/rfi/warranty.asp.
For questions about technical support or warranty, contact the seller, distributor, or
contact Focus Enhancements by email: support@focusinfo.com.
Unauthorized Use
Focus Enhancements is not responsible for the unauthorized use of its
equipment and will not make allowance or credit for unauthorized use or
access.
Unauthorized Alterations and Modifications
Alterations or modifications to Focus Enhancements equipment or software
that is carried out without appropriate authorization may invalidate the
product warranties and the user's right to operate the equipment.
FS-2/2E Studio DTE Disk Recorder User Guide
iv
Unauthorized Servicing
Do not attempt to service this product yourself. Opening or removing
covers may expose dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
Returning Materials
End Users
If the FS-2/2E was not purchased directly from Focus Enhancements, it is
necessary to contact the seller and determine what procedure is needed for
repairing the converter.
Direct Sales
(VARs, Distributors, and Corporate Customers
If the FS-2/2E has problems that cannot be corrected over the telephone by
Focus Enhancements technical support, it may be necessary to return the
converter to Focus Enhancements.
To contact Focus Enhancements:
Office Hours:
Email:
Telephone:
Fax:
Address:
Monday through Friday
8:00 AM to 5:00PM (Central Time)
support@focusinfo.com
763-398-1658
763-571-7688
Focus Enhancements, Inc.
1370 Dell Avenue
Campbell, CA. 95008
www.focusinfo.com
All materials shipped back to Focus Enhancements must be accompanied
by a Return Materials Authorization (RMA) number. Contact Focus
Enhancements Technical Support to receive a RMA number.
Write the RMA number clearly on the shipping label.
FS-2/2E Studio DTE Disk Recorder User Guide
v
Regulatory and Safety
Environmental Precaution
Focus Enhancements, Inc.
1370 Dell Avenue
Campbell, CA. 95008
Model Number: FS2-2E
Date of Manufacture:
Reference the Serial Number label attached to the unit.
FCC Class A
This product satisfies FCC regulations when shielded cables and connectors are
used to connect the unit to other equipment. To prevent electromagnetic
interference with electric appliances such as radios and televisions, use shielded
cables and connectors.
This equipment has been tested and found to comply within the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, correct the interference by
one or more of the following:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that used by the
receiver.
• Consult the dealer or an experienced radio/TV technician for help.
FS-2/2E Studio DTE Disk Recorder User Guide
vi
Documentation
This manual is written with the assumption that the user is familiar with analog
and digital video/audio signals and hardware.
Read, Retain, and Follow Instructions
All the safety and operating instructions should be read before the product
is operated.
•
Retain Documentation
Place documentation in a secure place for future reference on
operating and safety instructions.
Follow All Operating and Safety Instructions
•
Pay Attention to All Warnings
Warnings are provided to protect the operator, the equipment, and content.
This symbol indicates information about features, functions, operations, that is
of interest to the user.
FS-2/2E Studio DTE Disk Recorder User Guide
vii
Electrical Precautions
Do Not Expose to Moisture
Do not use this product near water or in an environment where it is
exposed to dampness or there is the possibility of it getting wet.
Do Not Remove Cover
There are
No User Serviceable Parts inside this unit. Servicing should be done
by qualified service personnel.
ON / OFF Switch in Stand-By Position
The On/Off switch Does Not Separate the Unit From the Main Power when it is
in the stand-by position.
Power Sources
Use only power sources that match those indicated on the marking label. If
unsure of the type of power supply that is available, consult your dealer or
local power company.
Do Not Overload Power Outlets
Do not overload wall outlets, extension cords, or integral convenience
receptacles as this can result in a risk of fire or electric shock.
Verify Power Plugs are Fully Inserted
To prevent potential electrical shock to personnel, verify that the FS-2/2E
power cord plug is fully inserted into a grounded receptor and that the
plug blades are not exposed.
ATTENTION
POUR PREVENIR LES CHOCS ELECTRIQUES NE PAS UTILISER CETTE
FICHE POLARISEE AVEC UN PROLONGATEUR, UNE PRISE DE
COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES
LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER
AUCUNE PARTIE A DECOUVERT.
Power-Cord Protection
• Routing Power-Cords
Route power supply cords so that they are not likely to be walked on
or pinched by items placed upon or against them. Avoid sharp angles
in the cord, particularly at plugs, convenience receptacles, and the
point where they exit the product.
Non-Use Period
•
During extended periods when the device is not used, unplug it from
the power source and retract the power-cord.
FS-2/2E Studio DTE Disk Recorder User Guide
viii
Grounding or Polarization
• Polarized
If this product is equipped with a polarized alternating current line
plug (a plug having one blade wider than the other), it will fit into the
outlet only one way. This is a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the plug. If the plug should
still fail to fit, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
Grounded
•
If this product is equipped with a three-wire grounding type plug, a
plug having a third (grounding) pin, it will only fit into a grounding
type power outlet. This is a safety feature. If you are unable to insert
the plug into the outlet, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the grounding
type plug.
Outdoor Antenna Grounding
If an outside antenna or
cable system is connected to
the FS-2/2E, verify that the
antenna or cable system is
grounded. This provides
some protection against
voltage surges and built-up
static charges.
Refer to Article 810 of the
National Electric Code,
ANSI/NFPA 70, for
information about the
proper grounding of the mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of grounding connectors,
location of antenna discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode. See Fig. A.
Lightning and Power Surges
During electrical storms or when left unattended and unused for long
periods of time, unplug the FS-2/2E from the power source and disconnect
the antenna or cable system.
Power Lines
Do not locate an outside antenna system in the vicinity of overhead power
lines, electric light or power circuits, or where it can fall onto such lines or
circuits.
FS-2/2E Studio DTE Disk Recorder User Guide
ix
When installing an outside antenna system, extreme care should be taken to
keep from touching such power lines or circuits as contact with them might
be fatal.
Optical Precaution
The use of optical instruments with this device will increase hazards to the eyes
hazard.
Maintenance and Moving
Cleaning
Unplug this product from the wall outlet before cleaning. The product
should be cleaned only with a polishing cloth or a soft dry cloth. Never
clean with furniture wax, benzine, insecticides or other volatile liquids
since they may corrode the cabinet.
Servicing
Unplug the device from the power outlet and refer servicing to qualified
service personnel under the following conditions:
• When the power-supply cord or plug is damaged.
• If liquid has been spilled, or objects have fallen into the product.
• If the product has been exposed to rain or water.
• If the product does not operate normally when following the
operating instructions. Adjust only those controls that are covered by
the operating instructions. The incorrect adjustment of other controls
can result in damage and often requires extensive work by a qualified
technician to restore the product to its normal operation.
• If the product has been dropped or damaged in any way.
• When the product exhibits a distinct change in performance.
Accessories and Replacement Parts
Use only attachments and accessories recommended by Focus
Enhancements.
Use only replacement parts specified by the Focus Enhancements or of
comparable quality and characteristics as the original parts.
Unauthorized substitution of parts can result in fire, electrical shock, other
hazards, and loss of warranty.
FS-2/2E Studio DTE Disk Recorder User Guide
x
Safety Check
Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks to determine that the product is in
proper operating condition.
Operating Environment
Location
Install this device on a sturdy, level surface, away from moisture and dust.
Heat
•
Locate this device away from heat sources such as radiators, heat
registers, stoves or other electrical devices (including amplifiers) that
generate heat.
Wall or Ceiling Mounts
•
This device should not be mounted to a wall or ceiling.
Any mounting of this device should follow its instructions, and
should use only mounting accessories recommended by Focus
Enhancements.
Moving
• Use appropriate safe lifting practices.
• Do not over load or unbalance carts when moving product.
Ventilation
Do not block the ventilation openings in the FS-2/2E cabinet. Overheating
can occur and damage the device. Do not place this device in a built-in
installation, such as a bookcase or rack, unless proper ventilation is
provided.
FS-2/2E Studio DTE Disk Recorder User Guide
xi
WARRANTY
For customers within the USA and Canada, FOCUS ENHANCEMENTS, Inc.
warrants this product against defects in materials or workmanship as follows:
For a period of TWO years from the date of purchase, FOCUS ENHANCEMENTS,
Inc. will repair or replace the unit, at our option, without charge for parts or labor.
After the period of TWO years, you must pay all parts and labor charges.
The limited warranty is extended only to the original purchaser. It does not cover
damage or failure caused by or attributable to Acts of God, abuse, misuse,
improper or abnormal usage, faulty installation, improper maintenance, lightning,
or other incidences of excessive voltage, or any repairs or tampering by other than
the FOCUS ENHANCEMENTS repair facility. It does not cover replacement of
batteries or other consumable parts, transportation costs or damage in transit. This
warranty will become void if the serial number or model number identification has
been wholly or partially removed or erased. Repair or replacement under the terms
of this warranty do not extend the terms of this warranty. Repairs or replacement
performed outside of the warranty period will carry a warranty for 60 days from
return shipment. This warranty can not be modified by an agent of FOCUS
ENHANCEMENTS, Inc. unless in written and signed by an officer of FOCUS
ENHANCEMENTS, Inc.
Should this product prove defective in workmanship or material, the consumer's
sole remedies shall be such repair or replacement provided by the terms of this
warranty. Under no circumstances shall FOCUS ENHANCEMENTS, Inc. be liable
for any loss or damage, direct, consequential, or incidental, arising out of the use of
or inability to use this product. Some states do not allow limitations on how long
an implied warranty lasts or the exclusions or limitations of incidental or
consequential damages, so the above limitations or exclusions may not apply to
you. This warranty gives you specific legal rights. You may also have other rights
which vary from state to state.
FS-2/2E Studio DTE Disk Recorder User Guide
xii
FS-2/2E Studio DTE Disk Recorder User Guide
xiii
FS-2/2E Studio DTE Disk Recorder User Guide
xiv
Table of Contents
Chapter 1 Introduction 1
What is a DTE Disk Recorder? 2
What is the FS-2/2E? 2
Basic Applications 3
Receiving, Unpacking, and Inspecting 3
Package Contents 4
Installation and Site Requirements 5
Mounting in a 19” Electronics Rack 6
Connecting Hard Drives 7
Inserting the Internal 3.5” IDE Drive 7
Using External Disk Drives 7
Physical Features 8
Front Control Panel 8
Rear Connection Panel 10
Setting Up the FS-2/2E 12
Formatting the Drive 13
Setting the Time and Date 14
Replacing the Power Module Fuse 15
Chapter 2FS-2/2E Functions 17
Edit/Utility/Input Buttons 17
Edit Function Keys 18
MARK IN - Mark In Key 18
MARK OUT - Mark Out Key 18
PLAYLIST – Add to Playlist key 18
KEEPER - Keeper Key 18
FOLDER - Folder Key 19
Utility Function Keys 20
OSD - (On Screen Display) 20
HDD – Hard Disk Drive Bypass Key 20
LOCK – Keypad Lock Key 20
REMOTE – Remote Key 20
E-E – Electronic to Electronic Key 20
Input Source Selection Keys 21
CMPST – Composite Video Source Input Key 21
Y/C – S-Video 21
CMPNT – Component Video Source Input Key 21
FS-2/2E Studio DTE Disk Recorder, User Guide
xv
SDI Serial Digital Video Source Input Key 21
DV Video Source Input Key 22
LCD Menu Soft Keys 22
Transport Control Keys 23
MENU 23
Back Index 23
Forward Index 24
Stop 24
Play 24
lRecord Key 24
SHIFT 24
Back Search 24
Forward Search 25
LCD Display 26
FS-2/2E Menus and Functions 30
Menu Items 32
Sub-Menu Available 33
Soft Keys 33
Record Menu 33
Normal Record 33
Retro Disk 34
Retro Cache 36
Loop Record 36
Still 37
Time Lapse 37
Control Mode Menu 38
Local 38
Remote 39
AV/C 40
Syncro Slave 41
Play Mode Menu 42
Play Clip 42
Loop Clip 42
Loop All 42
Play All 42
Play From Mode Menu 43
Track List 43
Play List 43
Folder List 43
Playlist Menu 44
Open 45
Save 45
New 46
Edit 46
REMOVE a Clip 47
INSERT a Clip 47
MOVE a Clip 48
View 49
Delete List 49
HDD Bypass 50
Internal HDD 50
Record Format Menu 51
FS-2/2E Studio DTE Disk Recorder, User Guide
xvi
Setup Menu 52
Set Date & Time 53
OS Version # 54
OS Upgrade 55
Copy Software to FS-2/2E Internal Drive 55
Load Software from External Drive 56
Restoring the Factory Default Operating System 57
PAL/NTSC 57
RS422 Remote 58
Audio Input 59
Audio In Levels 60
TC Mode 60
TC Set 62
TC Preset 62
UB Preset 63
TC Delay (FS-2E only) 63
Drop/Non Drop 63
On Screen Display 64
FF/RW Hi Res 64
GPI Port 65
Backlight 66
Stop Output 66
Audio Correct 67
Preferences 68
Folder Pref 69
Analog Out 69
Network Setup 70
IP SETTINGS 70
USER/PASSWORD 72
VIEW IP INFO 73
SERVICES 73
GENLOCK 75
Video Out Adj 76
Compnt Level 76
Utilities Menu 77
Organize PINN 77
Organize Clip 79
Organize OMF 79
Delete Clip 80
Format Disk 80
Partition 81
Repair 82
CHECK DISK 82
CURRENT CLIP 83
File Name 83
Factory Reset 83
Diagnostic 83
FS-2/2E Studio DTE Disk Recorder, User Guide
xvii
Chapter 3 Using the FS-2/2E85
How to Make a Recording 86
How to Playback 86
How to Put Recorded Clips on a Computer System 87
Mounting FireWire Disk Drives (Windows XP, 2000, 98SE and ME) 88
Using FS-2/2E Recorded Avid OMF Clips on Avid Editing Systems 90
Dismounting FireWire Disk Drives (Windows XP, 2000, 98SE and ME) 92
Mounting FireWire Disk Drives (Macintosh) 92
Dismounting FireWire Disk Drives (Macintosh) 93
How to Create a Playlist 94
How to Mark Scenes 95
Marking Scenes 96
Connecting the FS-2/2E to a Network 98
Chapter 4FS-2E Web Interface 99
Web Interface Home Page 100
The Web Interface 101
Recorder/Player Controls 101
Record 101
Playback 101
Recorder Status 102
Tracklist 103
Adding Tracks to a Playlist 104
Deleting Tracks from the Tracklist 104
Recorder Configuration 105
Playlist 107
System Configuration 108
Updating FS-2E Software via FTP 109
Connecting with the FS-2E 109
Chapter 5Reference 111
Technical Specifications 112
Inputs/Outputs 112
Control 113
Power 113
Physical Specification 113
Audio/Video/Timecode Specification 113
DTE File Formats 114
Disk Information 114
Compatible DV Formats 11 4
FS-2/2E LCD Display Modes 114
Supported RS-422 Commands 11 6
Shuttle Speed Parameters 116
Jog Speed Parameters 117
Custom Commands 117
Index index - 1
FS-2/2E Studio DTE Disk Recorder, User Guide
xviii
Chapter 1
Introduction
Thank you for purchasing the Focus Enhancements FS-2/2E DTE DV Studio Disk
Recorder.
The FS-2/2E is designed for use as a record or playback device in studios, mobile
vans and other installations.
The purpose of this User Guide is to explain the features and operation of the FS-2/
2E. Study the contents of this User Guide before attempting to use your FS-2/2E.
Check the Focus Enhancements website regularly for updates to FS-2/2E software
and documentation:
Alternatively, contact your Focus Enhancements dealer/distributor.
This chapter contains the following sections:
What is a DTE Disk Recorder? page 2
What is the FS-2/2E? page 2
Basic Applications page 3
Receiving, Unpacking, and Inspecting page 3
Package Contents page 4
Installation and Site Requirements page 5
Mounting in a 19 inch Electronics Rack page 6
Inserting the Internal 3.5 inch IDE Drive page 7
Using External Disk Drives page 7
Physical Features page 8
Setting Up the FS-2/2E page 12
Formatting the Drive page 13
Setting the Time and Date page 14
Replacing the Power Module Fuse page 15
www.focusinfo.com/support.
FS-2E Provides Greater Embedded Audio SDI Functionality
The FS-2E provides even more embedded audio SDI functionality. It includes the ability to
selectively record either channels 1 and 2 or 3 and 4 of the embedded audio of the input SDI
stream. It also provides full support of the SDI audio out. The FS-2E inserts the recorded audio
into the SDI output stream. The FS-2 does not possess these capabilities.
FS-2/2E Studio DTE Disk Recorder User Guide
1
Introduction
1.1 What is a DTE Disk Recorder?
1.2 What is the FS-2/2E?
A DTE Disk Recorder is a device that allows you to record or playback DV video
directly to/from a removable IDE disk drive or removable FireWire disk drives.
The FS-2/2E features analog and digital inputs and outputs including DV25, SDI,
composite, component, S-Video, AES/EBU digital audio and balanced analog
audio.
Audio and video are recorded to disk as a DV25 data stream in NLE native file
formats.
The FS-2/2E is a DTE Disk Recorder that mounts horizontally in a standard
electronics rack. With the FS-2/2E, it is possible to:
• Input DV25, SDI, composite, component, S-Video, AES/EBU digital audio
and balanced analog audio and record to disk in native DV25 NLE file
formats.
• Playback video from disk or transcode during recordings in DV25, SDI,
composite, component, S-Video, AES/EBU digital audio and balanced analog
audio formats.
• Capture clips to hard disk at the acquisition stage. There is no need to capture
them later.
• Record clips to disk in DTE Technology-based “edit-ready” file formats such
as Raw DV, AVI Type 1, AVI Type 2, Matrox AVI, Canopus AVI, Pinnacle
AVI, QuickTime and Avid DV-OMF. The FS-2E, and the FS-2 (with the
version 2.0 upgrade), also include DTE support for 24P AVI Type 2 (NTSC
only), and 24P Quicktime (NTSC only).This means clips are immediately
available to your NLE system without first having to transfer or convert the
files.
• Connect your FireWire disk directly to your computer or connect it using FS-
2/2E which allows mounting and dismounting of the drives without re-
cabling or computer re-boots.
• Use the FS-2/2E's 10/100BaseT Ethernet port to share files over a network
using FTP. This is not suggested for larger files. The FS-2E, and the FS-2 (with
the version 2.0 upgrade), also include IP control of the FS-2/2E. This means
you can control the FS-2/2E using a standard web browser.
• Jump from clip to clip without spooling through tape when in playback mode.
• As well as video, record and playback embedded DV audio in 2-channel (16-
bit, 48kHz) format.
• Record external timecode, embedded timecode or create your own timecode
using Free Run, Regen or Rec Run time code options. You can also preset
timecode and user-bit values.
• Record, play and navigate using FS-2/2E's VTR-style controls.
• Lock to your facilities Reference Video signal during playback and record.
FS-2/2E Studio DTE Disk Recorder User Guide
2
Introduction
• Record and recall a single frame of DV video and record user definable time-
lapse sequences.
• Use trick playback modes up to 30X/-30X fast-forward and rewind speeds,
reverse play, loop clip and loop entire disk.
• Control the FS-2/2E remotely using industry standard RS422 (Sony 9-pin),
FireWire (for starting record/pause or AV/C) from a DV based camcorder
1394 port. You can also control the FS-2/2E using RS-232C (using the optional
wired remote control available as an accessory). The FS-2E, and the FS-2 (with
the 2.0 software upgrade), can be controlled from your web browser using FS-
2/2E IP control. Refer to the section on the FS-2/2E Web Interface,
Interface
• Create and save multiple playlists on the FS-2/2E. These can be shared
between different units.
• Use the internal 120GB, 7200RPM, 3.5" IDE drive or daisy chain up to eight
FireWire (IEEE-1394) hard drives together for extremely long, uninterrupted
record times.
on page 99.
FS-2E Web
1.3 Basic Applications
You can use the FS-2/2E in the acquisition stage of production, the editing/post
production stage, and the presentation stage. The FS-2/2E is most useful in the
following applications:
• Presentation Video Source
•Broadcast Tape Deck Replacement
• Time Lapse Recorder
• Film-to-Disk Transfer
• NLE/Linear Edit Source/Recorder
• Endless Video Program Looping
• Security Recorder/Player
• Medical Recorder/Player
• Industrial Monitoring
• Video DJ and Karaoke Player
• Outside Broadcast
1.4 Receiving, Unpacking, and Inspecting
Upon receipt of the FS-2/2E unit, examine the shipping container. If there is
evidence of damage or rough handling, have an agent of the carrier present when
the equipment is unpacked.
Unpack the equipment carefully. Inspect it for scratches, dents, or cracks. If the
equipment is damaged, save all packing materials and notify both Focus
Enhancements and the carrier immediately.
FS-2/2E Studio DTE Disk Recorder User Guide
3
Introduction
1.4.1 Package Contents
1
2
3
7
6
4
5
Please take a moment to study the contents of your FS-2/2E package. You
should have the following contents:
1. One (1) FS-2/2E unit with attached rack mounting ears
2. One (1) 120GB IDE disk drive in caddy
3. One (1) User Guide
4. One (1) 6-pin to 6-pin FireWire cable (for External Drive connection)
5. One (1) 6-pin to 6-pin FireWire cable (for front panel port loop)
6. One (1) Focus Enhancement's DV Conversion Suite Demo Disk
7. One Power Cord
8. One (1) Focus Enhancement's Warranty Card and Statement (not
shown)
If any of these items are missing, contact Focus Enhancements or your FS2/2E dealer/distributor immediately.
You may need to purchase cables to connect more than one hard disk drive
to the FS-2/2E at a time. Your Focus Enhancements dealer can help you
identify additional cables you may need.
FS-2/2E Studio DTE Disk Recorder User Guide
4
1.5 Installation and Site Requirements
Focus Enhancements recommends that FS-2/2E units be installed in a restricted
access area, such as an equipment room or closet and the installation be performed
by trained installers.
The units are designed and tested to operate reliably between +5 - +40C (41 - 104 F).
To maintain this range, consider the following:
• Air temperature surrounding the equipment must remain within the specified
range.
• Air flow around the equipment must be sufficient to maintain proper
operating temperatures
If in doubt about the site temperature, take measurements to be certain. If
measured temperatures fall outside the defined ambient temperature range, you
must bring the temperature within the defined range.
Storage temperature for the units must remain between -20 - +60C (-4 - 140 F).
Introduction
FS-2/2E Studio DTE Disk Recorder User Guide
5
Introduction
1.6 Mounting in a 19 inch Electronics Rack
The FS-2/2E measures 15.89” high x 17.36” wide by 3.47” deep. It is an 2RU chassis
featuring front rack mount ears to be installed into a standard 19” audio/visual
rack. There must be room behind the unit for the attachment of cables.
To mount the FS-2/2E in a standard 19” audio/visual rack, do the following:
1. Determine the desired location.
The FS-2/2E requires 3.47 vertical inches of rack space.
To prevent overheating, the FS-2/2E requires a minimum of 1.75 vertical
inches of space above and below the unit.
2. The FS-2/2E includes a pair of universal mounting ears on the front sides of
the unit that support standard 19” audio/visual racks. Using the provided
hardware, mount the FS-2/2E securely in the rack.
Universal Mounting EarsUniversal Mounting Ears
Mounting Screws
(2 per Mounting ear)
3. Connect the FS-2/2E unit to the wall current using the attached power cord.
FS-2/2E Studio DTE Disk Recorder User Guide
6
1.7 Connecting Hard Drives
1.7.1 Inserting the Internal 3.5 inch IDE Drive
Insert the internal 3.5 inch IDE drive as follows:
1. Remove the drive from its packaging.
2. Slide the drive carefully into the bay until it is seated firmly.
Introduction
Lock Handle
Drive Bay
3. Press the Lock Handle flush with the chassis face to lock the drive in
Release Lever
place.
To remove the drive, slide the
Release Lever to the right. The Lock Handle
disengages. Pull the drive toward you to remove it.
This drive is not intended for hot-swap operation.
1.7.2 Using External Disk Drives
In addition to using a 3.5 inch IDE drive in the internal slot, you can also
connect any FireWire disk drive to the HDD I/O port on the FS-2/2E.
Power a single FireWire disk drive on the FS-2/2E at any given time.
If you are using more than one external FireWire drive, you must provide
external power to them. It may also be necessary to partition and format the
drives before their use with the FS-2/2E. Refer to
page 13 for instructions on preparing drives before use.
Hot-swapping External FireWire Drives
You can hot-swap connected external FireWire HDDs on the FS-2/2E. This means
you can disconnect and connect drives from the system without the need to power
cycle the unit. However, make sure the FS-2/2E is in STOP mode before removing a
disk drive.
Formatting the Drive on
FS-2/2E Studio DTE Disk Recorder User Guide
7
Introduction
1.8 Physical Features
The FS-2/2E features two main surfaces, the front control panel and the rear connector
panel.
Disk Drive Bay
Power Switch
and LED
Jack Volume Control
Jack Volume Control
Headphone
Headphone
1.8.1 Front Control Panel
The front control panel contains the seven control areas, as shown in the illustration
below and described in this section:
•
Power Switch and Power LED
This is the FS-2/2E's main power switch. This switch, although mechanical, is
controlled using software. When the power switch is set to
in most cases the unit takes a moment to power down. During this time, the
FS-2/2E is ensuring that any files that have not been closed properly in a
record session get closed. This prevents errors occurring on particular files.
The green LED above the power switch is
•
Disk Drive Bay
The disk drive bay accepts a standard 3 1/2” removable disk drive in the
supplied sled. Minimum system requirements for this drive are 7200RPM
with a 2MB cache. Drive performance may vary. Focus Enhancements
recommends that you use a FS-2/2E qualified and tested disk drive. Check
the Focus Enhancements website for an updated list. This bay is not intended
for hot swap operation.
Edit / Utility / Input Keys
•
These keys contain the edit, utility and input select functions for the FS-2/2E.
In some cases, these buttons work in conjunction with the FS-2/2E menus on
the display.
Edit / Utility / Input
Keys
LCD
Display
Soft Keys
ON when the unit is powered up.
Transport
Keys
ON and then OFF,
FS-2/2E Studio DTE Disk Recorder User Guide
8
Input selections are either Composite, Y/C (S-Video), Component, SDI
or DV. An audio source must be selected for each input using the
SETUP > AUDIO INPUT menu, the Timecode mode in the
SETUP > TC MODE menu, and the reference video source in the
SETUP > GENLOCK > SOURCE menu. For component inputs/outputs
you must select the video standard when used in
Refer to
•
LCD Display
Compnt Level on page 76 for more details.
NTSC mode only.
The FS-2/2E LCD displays the FS-2/2E’s current status including
track number, disk number, timecode, record / playback mode as well
as other information. It also displays the FS-2/2E menu system. The
LCD is a green backlit 128x64 graphical display.
Transport Control Keys
•
This set of keys controls playback and record functions of the FS-2/2E.
These functions include play, reverse play, fast forward, fast rewind,
forward frame, back frame, next track, previous track, stop, record,
and so on.
•
Display Soft Keys
This set of keys enables you to navigate the FS-2/2E menus. The
function of the keys varies depending on what is displayed at the base
of the FS-2/2E LCD. Refer to
LCD Menu Soft Keys on page 22 for more
information.
•
Headphone Jack (3.5mm) and Volume Knob
This jack is for connecting a pair of monitor headphones. You can
monitor audio of the selected input (even if E-E is not selected) when
not in record mode. When in record or playback mode, you can
monitor the current audio. The headphone jack also includes a volume
control.
Introduction
FS-2/2E Studio DTE Disk Recorder User Guide
9
Introduction
1.8.2 Rear Connection Panel
The FS-2/2E rear panel, shown below, contains control and audio/video
input/output areas described in this section.
You can select any of the available inputs as a source. When selected, that
source is what is recorded to disk. If the unit is in E-E mode or recording, all
outputs are live with the incoming signal.
For any particular video input, there is an associated audio input selected as
a default. You can change that default to another input utilizing the
INPUT MENU
2
1
3
under SETUP. Refer to Chapter 2 for more information.
4 5
6
AUDIO
7
9
8
11 12 13 14
10
19 18 17
20
16
1. GPI - For connection of the optional wired remote control (ACSS-0019-
15
01), the optional RS232C cable (CBLA-0113-01) or contact closure
cable. The GPI plug accepts a 3.5mm TRS connector.
2. Front Panel HDD Port Loop Through - When patched to the To HDD
port, this connector activates the front panel FireWire port for
connection of external HDDs.
3. RS422 Control - This is the input connector for external RS422 control
devices.
4. SDI Input - For connecting SDI input sources. The FS-2E provides the
selection of channels 1 and 2 or 3 and 4 of the embedded SDI audio.
Refer to the
Input
on page 59. The FS-2 does not have this capability.
SDI Output - For output to SDI devices. The FS-2E inserts two channels
AUDIO INPUT > SDI > EMBEDDED sub-menu on Audio
of audio into the SDI output stream. Only the FS-2E has this capability.
5. Y/C Input - For connecting Y/C (S-Video) input sources.
Y/C Output - For connecting to Y/C (S-Video) devices.
6. Composite / Y Input - For connecting composite input sources or the Y
signal for component input sources.
Composite / Y Output - For output to composite devices or the Y signal
to component devices (select either composite or component form
ANALOG SETTINGS in the SETUP menu).
7. Pb Input - For connecting the Pb signal from component input sources.
Pb Output - For output of the Pb signal to component devices.
FS-2/2E Studio DTE Disk Recorder User Guide
10
Loading...