Page 1
Windows
CERTIFIED FOR
TM
TM
Vista
User Manual
RK-360
Compatible with Windows 2000 / Windows XP / Windows Vista /Windows 7.
O
ompliant
S
R
o
H
Page 2
Page:
1
RK-360, a best choice in wireless mini keyboard.
RK-360 is based on 2.4Ghz radio frequency, 10-30 meters effective working rang e
and 360 degree navigation, with sleek and elegant design. mini, thin, and smart,
You don't need to install any driver, it will automatic start all of function when you
plug the receiver, It is great device to Media Center PCs, Home Theater PCs,
Living Room, or Car PCs or IPTV or IP Settop Box.
There is no cables connected to the keyboard, you can put it away to save spce
when you finish using it. it is orgonomically designed allwoing for comfortable
use one table or lap. or you can put even on bed or settee when you are lie-in.
You will like this speical mini keyboard, please read carefully the information and
instructions contained in this manual, and you are sure to obtain a obtain a highe r
level of computing enjoyment.
Page 3
Compatible with Windows 2000 / Windows XP / Windows Vista / Windows 7.
Keyboard:
Receiver:
USB Dongle.
Dimension: 78 x 21.5 x 10 mm.
2.4 Ghz radio frequency, 10 meters effective working, farthest amount to
30 meters.
360-degree navigation, sleek and elegant design.
86 keys Mini Keyboard, with 10 Internet / Multimedia hot-keys.
Bounce Time: less than 10m sec.
Non-skid rubber feet.
2-AA batteries included for up to 3 months use.
Welcome to combine with remote control RM518 as a combo set.
Size: 304 x 151 x 23 mm.
Page:
2
Specification
Page 4
1. Turn on the Computer.
2. Plug the USB Receiver of the
keyboard unto the USB ports
of your computer.
3. Open the battery cover on back of keyboard, place AA A batteries
inside the battery compartment. Close the battery compartment
cover.
Push to open
Installation
Page:
3
place AAA batteries inside
the battery compartment
Page 5
1. RF Signal LED on the receiver will flash when the keyboard is being
used. (Picture A)
Page:
5
Remarks
Receiver(A)
Keyboard(B)
2. When Battery Low LED lights, it means the keyboard requires changing
batteries. (Picture B)
Page 6
4. Setting ID
Keyboard Setting:
Press ID button on the receiver, the LED is on flash which means
ID is searching.
(Picture A)
Press ID button on Back of the keyboard, the LED is off
which means setting is successful. (Picture B)
b.
(Picture A)
Page:
4
a.
(Picture B)
Page 7
Keyboard Description
Page:
6
Keys Description
Page 8
Page:
7
Trouble Shooting:
If your keyboard or remote control can not work after installation, pls check
followings:
a. Make sure you have connected the receiver correctly to the computer; the
receiver has been properly plugged onto computer’s USB port.
b. Make sure you have inserted batteries into keyboard, and they are compartment
correctly.
c. If without any interference, such as other computer peripherals, the working
distance (the distance between keyboard and the receiver) is about 10 meters.
If using more than two units and interfere occurred, please reset ID again.
Notice:
The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Important note:
To comply with the FCC RF exposure compliance requirements, no change to the
antenna or the device is permitted. Any change to the antenna or the device could
result in the device exceeding the RF exposure requirements and void user’s
authority to operate the device.
WEEE Directive & Product Disposal:
At the end of its serviceable life, this product should not be treated as household
or general waste. It should be handed over to the applicable collection point for the
recycling of electrical and electronic equipment, or returned to the supplier for
disposal.
Internal / Supplied Batteries:
This symbol on the battery indicates that the battery is to
be collected separately.This battery is designed for separate
collection at an ppropriate collection point.
Page:
7
Page 9
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Page:
8
The Federal Communication Commission Radio Frequency Interference Statement
includes the following paragraph:
The equipment has been tested and found to comply with the limits for a Class B Digital
Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radio frequency energy and, if not installed
and used in accordance with the instruction, may cause harmful interference to radio
communication.
However, there is no grantee that interference will not occur in a particular installation.
If this equipment dose cause harmful interference to radio or television reception,
which can determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Loading...