Page 1
Versailles
Coal Effect Gas Fire
INSTALLATION, SSERVICING
AND UUSER IINSTRUCTIONS
All iinstructions mmust bbe hhanded tto tthe uuser ffor ssafekeeping
Revision A 02/04
Country(s) of destination: GB, IE
Focal Point Fires plc, Avon Trading Park, Christchurch, Dorset BH23 2BT
: (01202) 499330
Fax: (01202) 499326
www.focalpointfires.co.uk
e-mail: [email protected]
Balanced Flue
Page 2
INSTTALLATTION IINSTTRUCTTIONS
Preliminary Notes Before Installation
This appliance is a High Efficiency, Balanced Flue, Inset Live Fuel Effect appliance. It provides radiant and convected warmth utilising the latest type burner
technology. It is 'room sealed' providing up to date technology in efficiency
and safety.
The fire is designed to fit various types of situations as listed in the Installation
Requirements. The appliance is provided complete with its own integral flue
system to be tailored to the individual installation.
The appliance must be installed by a competent person in accordance with
Gas Safety (Installation and Use) Regulations 1998. It is strongly recommended
that a CORGI registered engineer is used for this purpose, as they are the only
class of persons approved by the HSE under the above regulations.
Read all these instructions before commencing installation.
This appliance must be installed in accordance with the rules in force and only
used in a sufficiently ventilated space. No additional ventilation is normally
required. The appliance does not use room air for combustion or operation of
the flue, but an adequate supply of fresh air to maintain temperatures within
limits is advisable.
This appliance is factory set for operation on the gas type, and at the pressure
stated on the appliance data plate.
Page 3
IMPORTANT NNOTES
This fire is an Inset Live Fuel Gas Fire providing radiant and convected warmth. It is designed to operate on
Natural Gas following factory set adjustments. See Data Plate on appliance for gas type and pressure.
It is the LAW that all gas appliances and fittings are installed by a competent person (such as a CORGI registered fitter) and in accordance with the Gas Safety (Installation and Use) Regulations 1998, the relevant British
Standards for Installation, Codes of Practice and in accordance with the Manufacturers' Instructions. The
installation shall also be carried out in accordance with the following regulations:
The Building Regulations issued by the Department of the Environment, the Building Standards (Scotland)
(Consolidation) Regulations issued by the Scottish Development Department.
BS 5440 part 1, BS 5871 part 1, BS 6891
Note: For Republic of Ireland, reference should be made to the relevant standards governing installation.
Failure to comply with these regulations could lead to prosecution and deem the warranty
invalid.
This appliance must be installed in accordance with the rules in force and used only in a sufficiently ventilated space. The appliance does not use room air for combustion or operation
of the flue, but a supply of fresh air is advisable to maintain temperatures within limits. The
combustion air supply for this appliance is ducted from the outside air by an integral flue
system. The terminal of this flue system must always be kept clear of vegetation, new buildings, conservatories, extensions, sheds or other potential obstructions and able to perform
its function correctly.
Consult ALL instructions before installation and use of this appliance.
This appliance is provided with its own integral flue system and must only be used as
described in these instructions with that flue system alone. NEVER connect to, open up,
extend or in any other way modify the flue system and terminal other than shortening it for
installation as described in these instructions.
This appliance is free from any asbestos material. Refractories and coal bed are constructed
from ceramic fibre.
Secction Contentss Pagge NNo.
1.0 Important NNotes 1
2.0 Appliance DData 2
3.0 Installation RRequirements 3
4.0 Terminal LLocation 4
5.0 Site RRequirements 5
5.1 Ventilation 5
6.0 Unpacking tthe AAppliance 6
6.1 Component Checklist 6
7.0 Appliance IInstallation 7
7.1 Preparing the Appliance 7
7.2 Preparing the Wall Location 8
7.3 Outside Wall Apeture 8
7.4 Gas Supply Routes 9
7.5 Installation Method 1 10
7.6 Installation Method 2 10
7.7 Installation Method 3 11
7.8 Flue Preparation 12
Secction Contentss Pagge NNo.
8.0 Gas SSupply 13
9.0 Fitting CCavity BBox 14
9.1 Cable Fixing 15
10.0 Fuel BBed LLayout 16
11.0 Decorative FFrame aand HHood 17
12.0 TTesting aand CCommissioning 18
12.1 Operating the Appliance 19
12.2 Spark Failure 19
12.3 Setting Pressure 19
13.0 Briefing tthe CCustomer 20
14.0 Servicing 21
14.1 Cleaning the Coals 21
14.2 Dismantling/Servicing the Burner 22
14.3 Removing the Firebox 23
14.4 Pilot Assembly 23
14.5 Testing for Firebox Leakage 24
15.0 Troubleshooting GGuide 25
1.0
Page 4
INSTALLATION RREQUIREMENTS
Compatible wall thickness for the installation methods described in this guide are as follows:
Internal
The fire has been designed to be installed in two main ways as shown in the table; either to fit into a suitable
opening created in the inner leaf of an outside wall or a false chimney breast/extended fire surround built to
conceal the appliance. The appliance can also be fitted into an unserviceable or inoperative fireplace served
by a disused natural draught flue providing that the requirements for terminal siting and flue length can still be
successfully met. It is recommended that the old flue be sealed off.
The flue pipe must be able to pass right through the outside wall to duct fresh air in to the fire and exhaust
gases out correctly. The cavity box and firebox must be installed onto a suitable non-combustible insulating
surface at least 12 mm thick, covering the entire base area of the box. The fire must be used with a fire surround and or back panel set capable of withstanding 180 degrees C minimum. Any combustible materials
directly behind the fire frame (or back panel) and close to the cavity box of the fire must be removed and
replaced with non-combustible material such as cement, browning, 'Superlux' board or equivalent materials.
External
The appliance requires a direct through the wall route behind the cavity box to the outside air. Minimum and
maximum wall thickness is shown in the table at the beginning of this section. The terminal requires adequate
clearances from other buildings, openings and obstructions to operate safely and correctly. Please refer to the
diagram shown in the flue terminal position section. Terminals exhausting in passageways, over footpaths etc
may be subject to local bye-laws, and must not create a nuisance. If in doubt contact your local council for further advice. In any case, the safety cage which is supplied with the terminal should be fitted to ensure no
problems arise.
Avoid siting the terminal outlet close to combustible materials e.g. plastic drain pipes or fences etc. If it is
unavoidable, a metal deflector must be used if the object is significantly heated. Covered areas such as car
ports or covered walkways should be avoided, but if necessary, the following guidance may be used; The covered area should have at least two open sides (i.e. it comprises roof and maximum one supporting wall). If
more than one wall is filled, advice should be sought from CORGI on the locations suitability. For minimum
clearances see section on flue terminal location. Particular care should be taken with plastic roofs, if in any
doubt the minimum distance stated should be to the lowest part of the roof.
Installation Method - Min and Max Wall Thickness Min (mm) Max (mm)
METHOD 1: Inset into inner leaf of outside wall. 287 693
METHOD 2: Installed against inner leaf of outside wall with false chimney
breast or rebated surround concealing firebox. 100 506
APPLIANCE DDATA
Gas Group G20 Natural Gas CAT I2H
Inlet Pressure 20 mbar
Max Energy Input Gross 3.5 kW Net 3.15 kW
Max Gas Rate 0.33 m3/h
Min Energy Input Gross 2.1 kW Net 1.89 kW
Pilot Energy Input Gross 140 W Net 120 W
Setting Pressure High 17.0 mbar (± 1.0 mbar) Low 6.5 mbar
Main Injector Burner Stereo size 60
Gas Inlet Connection 8 mm compression
Ignition Piezo spark
Spark Gap 4.0 mm (± 1.0mm)
Weight 20 Kg
Efficiency Class Class 1
NOx Class Class 4
Please see Data Badge affixed to appliance for current data.
This appliance is for use only with the gas type, and at the pressure stated on the appliance
Data Badge.
1.0
1.0
Page 5
INSTALLATION REQUIREMENTS (continued)
As with any flue outlet, some dicolouration of the wall around the terminal may occur with light coloured
walls. Always avoid siting the terminal in conspicuous positions on light walls.
Terminal siting guidance is given in the next section but as a general rule avoid ledges, drain pipes, projections
etc. The prevailing wind conditions combined with such objects can combine to produce unexpected conditions around the terminal.
TERMINAL LLOCATION
This appliance is provided with its own integral flue system and must only be used as described in these
instructions with that flue system alone. NEVER connect to, open up, extend or in any other way modify the
flue system and terminal other than shortening it for installation as described in these instructions.
Terminal PPossition Minimum DDisstancce ((mm))
A - Directly below and openable window or other opening e.g. airbrick 300
B - Below gutters, soil pipes or drain pipes 300
C - Below eaves 300
D - Below balconies or car port roof 600
E - From vertical drain pipes or soil pipes 75
F - From internal and external corners 600
G - Above ground, roof or balcony level 300
H - From a surface facing terminal 600
I - From a terminal facing a terminal 600
J - From an opening in a car port into dwelling (e.g. window) 1200
K - Vertically from a terminal on the same wall 1500
L - Horizontally from a terminal on the same wall 300
SITE RREQUIREMENTS
The appliance may be installed by one of the following methods:
1. Fitment against the inner face of an external house wall with a suitably constructed false chimney
breast or rebated fire surround to enclose the depth of the fire. If a timber false chimney breast is con
structed, clearances and insulation must be as for a timber constructed wall.
2. Insertion into a purpose made opening in the inner leaf of a cavity wall or a disused conventional fire
place opening. Bridging the cavity may cause unwanted moisture to track to the inside of the house
from the cavity. Protection from moisture and falling debris above the cavity box should be provided.
If in doubt, consult local building control officers.
3. Installation into a timber framed house wall using clearances and insulation as described in the appro
priate section. If in doubt, consult local building control officers.
1.0
1.0
1.0
Page 6
SITE REQUIREMENTS (continued)
The opening dimensions for insetting the appliance must be;
WIDTH
between 430 mm and 445 mm, and
HEIGHT
between 565 mm and 575 mm high. The opening must be these sizes for the full depth of the cavity
box in non-combustible applications. Applications involving combustible materials e.g. timber battens in false
chimney breasts, must use appropriate clearances and insulation methods as described in the relevant section
of these instructions.
Opening
DEPTH
must be 187 mm or greater. Opening
DEPTH
includes any plaster, cement or infill/back pan-
els that form part of the installation.
In the event that the fire is sited in a disused or unserviceable fireplace served by a natural draught flue, the
passageway into the flue and any existing under grate draught device should be sealed off to prevent loss of
heat or creation of draughts.
If a concealed gas connection is to be made, the supply pipe should always be sleeved through walls and
floors using the shortest possible route. It is possible to install the gas supply from the side of the hearth and
round into the cavity, but use only factory sleeved pipe. No more than 1.5m of 8mm dia pipe must be used to
avoid unnecessary pressure drops.
The wall for the opening must be non-combustible or prepared as described in the relevant section. Bare plasterboard must be protected by non-combustible plaster or replaced with 'Superlux' board for example. Any
gap between wall boards and the wall must be filled using glass fibre insulation, silicone mastic or similar
method to prevent heat ingress.
If the appliance is to be installed as a 'hole in the wall' fire, it does not require any hearth as such, providing it
is mounted more that 150mm (6") above floor level. NOTE: Depending on the fret and trim type supplied with
the fire, a suitable ledge for placement of the fire front may be required.
The appliance requires a hearth with non-combustible surface of at least 12 mm thick, projecting 100mm from
the front of the appliance. The top surface must be at least 50 mm above the surrounding floor level, or be
surrounded by a raised edge or fender 50 mm high. Any type of fire surround used with this appliance must
be adequately sealed to the wall and floor to prevent excess draughts from around the back of the fire.
A combustible shelf may be fixed to the wall above the fire, providing that it complies with the dimensions
given below. The shelf depth may be greater but the height must also be increased accordingly. An increase in
height of 25 mm is required for every 12.5 mm of additional shelf depth. For shelves that are too low, protective devices can be used such as metal heat deflectors, but it must be assured that the shelf does not reach an
unacceptable temperature before relying on such a solution. A non-combustible shelf may be fitted to within
100mm of the top edge of the fire frame, but any articles placed on it must also be tolerant of high temperatures.
Combustible materials, such as wood, may be fitted to within 100mm (4in) of either side of the fire frame/trim,
providing the forward projection does not exceed 100mm (4in). Any combustible side walls must be at least
500mm to the side of the radiant heat source.
As with all heating appliances, any decorations, soft furnishings, and all coverings (i.e. flock, blown vinyl and
embossed paper) positioned too close to the appliance may discolour or scorch.
VENTILATION
No purpose provided ventilation is required for this appliance because it is room sealed. The requirements of
other open flued appliances operating in the same room or space must be taken into consideration when
assessing ventilation.
The combustion air supply for this appliance is ducted from the outside air by an integral flue system. The terminal of this flue system must always be kept clear of vegetation, new buildings, conservatories, extensions,
sheds or other potential obstructions and able to perform its function correctly. A supply of fresh air into the
room is advisable to maintain temperatures within limits.
For Republic of Ireland, see relevant rules in force.
Maximum depth of shelf Minimum distance from hearth to underside of shelf
180mm 850mm
1.0
1.0
Page 7
UNPACKING TTHE AAPPLIANCE
Stand the carton the right way up, cut the strapping bands and remove the top endcap. Read ALL these
instructions before continuing to unpack or install this appliance.
Remove the box containing the cast front fret, and the box containing the ceramic coals and other ceramic
firebed components. Remove the cardboard packing pieces, the flue tube and terminal assembly and any
other bags or boxes containing fittings or other parts. When all loose parts have been removed, the outer
sleeve may be lifted off to reveal the appliance. Check that the components supplied correlate with the component checklist. Please dispose of all the packaging materials at your local recycling centre.
COMPONENT CCHECKLIST
QUANTITY DESCRIPTION
1 Cavity box, firebox and burner assembly fitted with glass panel.
1 Decorative frame - 3 piece
1 Hood
1 Cast front fret with separate ashpan door
1 Moulded ceramic fibre combustion matrix
14 Individual ceramic coals (5 moulded and 9 broken)
2 Ceramic fibre side cheeks
1 Ceramic brick panel
1 Sealing grommet
1 Cable fixing kit
1 Screw and rawlplug pack
1 Terminal guard cage
1 Set of manufacturers instructions and warranty card
1 No 8 x 10 lg Self tapping screw
1 Flue Assembly
1 2" foil tape
APPLIANCE IINSTALLATION
Note: EEnssure tthat tthe ggass ssupply iiss iissolated bbefore ccommenccingg iinsstallation oof tthe aappliancce.
The fireplace opening and environment must be in compliance with specifications laid down in the appropriate sections of these instructions.
PREPARING TTHE AAPPLIANCE
Remove the appliance from its carton as described previously and stand on a dust sheet. Remove the glass
panel and place it and the coals, ceramics and fixing safely to one side.
Lay the fire on its back. Remove the firebox assembly from the cavity box by removing the fixings provided on
the front of the frame of the firebox. Place the firebox to one side for the time being. Knock out holes are provided in the rear and sides of the cavity box for use where concealed pipework is required. Knock out the
appropriate hole with a sharp tap from a hammer and fit the rubber grommet supplied. A small incision can
now be made in the rubber to slip snugly around the outside of the supply pipe and sleeving.
Note: DDo nnot iinsstall oor uusse tthe aappliancce wwithout tthiss sseal iin pplacce.
If a hole is inadvertently opened, reseal with an intact grommet. Failure to fit this seal correctly may allow
heat to escape unnecessarily, or allow cold draughts in.
PREPARING TTHE WWALL LLOCATION
From inside the house, firstly find the FINISHED HEARTH
LEVEL, including any decorative hearth that will be in place
when the fire is in position. This is the reference plane to
which you should work. Mark the vertical centreline of the
fireplace on the wall. Next, mark the centre of the flue pipe
hole. This is 457 mm from the FINISHED HEARTH LEVEL.
Pilot through the wall to ascertain the outside finished flue
centre line. If necessary, check locations of wires and pipes
in the wall first.
457mm
Pilot hole
Proposed location of
appliance
Finished hearth level
1.0
1.0
1.0
1.0
1.0
Page 8
OUTSIDE WWALL AAPERTURE
Check the outside flue terminal location using the pilot hole as a guide. Make any adjustments to the fire location or the surroundings as required to comply with terminal siting. Finally, core drill through the outside wall
with a 155mm (6") core drill to provide the location for the outside part of the flue. If a core drill is not available, mark a 155mm diameter circle and stitch drill or chisel out the required area of brick. Clear rubble from
the cavity and clear back any insulation material.
If required, the outside wall aperture can be created at a later stage from inside the property, through the
inside wall aperture. If this is desired simply move on the next sections first.
GAS SSUPPLY RROUTES
The gas supply may enter the fire over the
hearth or by concealed connection behind
the front of the fire.
Following preparation for the fixing method,
the concealed gas supply (if required) can
now be put into place. When the opening is
ready for installation of the fire, the gas supply can be routed as shown in the following
diagram. The ends of the sleeving in which
the gas pipe is run should be sealed. The
end of the 8mm pipe should be temporarily
sealed to prevent the ingress of debris during fixing. An isolator cock or restrictor elbow must be fitted to the incoming supply to facilitate servicing.
Concealed pipes should not be routed through walls without being protected by sleeving or conduit.
For installation method 1 (mounting against a wall) the supply can be routed in the normal manner. For installation method 2 (insetting into the inner leaf of a cavity wall) use only factory sleeved pipe in a continuous
unjoined length in the cavity of the wall and areas that communicate with the cavity. This is a permitted gas
supply pipe routing.
INSTALLATION MMETHOD 11 (against aan iinside wwall)
Thiss mmethod rrequiress nno ssiggnificcant mmodificcationss tto tthe iinternal wwall oof aa pproperty aand iiss aacchieved bby uussingg
either aa ssurround wwith eextended rrebate oor aa ffalsse cchimney bbreasst oof mminimum 11877mm iinternal ddepth.
A - Opening width Min.
40mm Max. 440mm.
B - Overall Width 480mm.
C - Opening Height Min.
555mm Max 575mm.
D - Overall Height 590mm
E - Recess Depth 187mm
F - Plasterboard protection
1.0
1.0
1.0
Page 9
INSTALLATION MMETHOD 11 ((continued)
Centring on the pilot hole already drilled, core drill or chisel a hole 155mm diameter from the inside of the
wall. If loose fill cavity insulation material is present, the material will have to be retained by inserting 25 50mm of fibre glass or rock wool insulation tightly into the cavity. Where the cavity does not have such insulation material it is still good practice to do the same to provide protection if it is introduced at a later date.
At this point, the false chimney breast should be installed, taking into account any guidance given in the section on timber framed buildings as far as insulation and clearances are concerned. As a general rule, when the
false chimney breast is constructed from combustible materials, the cavity box must be insulated with 50 mm
of fibre glass wool or rock wool to the sides and rear and 100 mm to the top.
Finally install the fireplace or fire surround and back panel/marble to its finished location.
INSTALLATION MMETHOD 22 ((recessing iinto wwall)
This method allows for installation of the appliance with the rear part recessed into the inner leaf of a cavity
wall. This should enable a standard fire surround and back panel/hearth set to be fitted to the wall with the
fire presented naturally in a flush fitted manner. The structural integrity of the wall must be maintained.
Check on cavity insulation type if installed to the house and if of the loose fill variety, take precautions to prevent excessive loss of material when the inner leaf is opened up. Packing the cavity firmly with min 50mm of
rock wool or glass fibre should help hold back any loose material now or in the future.
To maintain the structural integrity of the wall, the fitment of a suitable lintel is recommended. It is sometimes
possible to install without a lintel depending on wall type, but the guidance of a qualified professional or local
building control officer is essential to confirm this.
A - Opening width Min.
40mm Max. 440mm.
B - Overall Width 480mm.
C - Opening Height Min.
555mm Max 575mm.
D - Overall Height 590mm
E - Recess Depth 187mm
F - Plasterboard protection
1.0
1.0
Page 10
INSTALLATION METHOD 22 ((continued)
Mark out the area of the proposed fireplace opening on the wall. Obtain a suitable concrete or steel lintel
from a builders merchant. Drill four holes at the corners of the lintel position, squarely over the fireplace opening position and centrally under a block joint if possible. Clear out the block work in the area and insert the
lintel by saw or stitch drill and chisel. Do not dry bed the lintel - always bed on mortar and securely slate pin.
Clear out the block work from below the lintel to form the opening for the cavity box of the fire to be inserted.
The top of the exposed area of cavity must be sealed against the ingress of moisture dripping from above. The
best way to do this is a cavity tray, but an easier and quicker method is to affix a 'Supalux' or equivalent board
into the cavity. Slope the board towards the outside wall and support with screws, cement, 'Unibond' or silicone mastic etc. This will harmlessly guide all moisture to the outside wall. The exposed sides of the cavity
must be packed with a good depth (minimum 50mm) of glass fibre or rock wool to prevent draughts and heat
loss even if no loose fill material is present. It is good practice to insulate the rear of the fire from the cavity to
prevent heat loss and condensation.
The non-combustible hearth may now be put in place. Again, this should not bridge the cavity where it projects into the wall space. Finally install the fireplace or fire surround and back panel/marble to its finished location.
INSTALLATION MMETHOD 33 ((timber fframed bbuildings)
Where removal of any part of a timber frame is undertaken, the structural integrity of the wall must be
retained. The advice of your local building control officer should be sought. If the property is under any NHBC
warranty it is also advised that their advice on this kind of modification is sought.
Either of the two preceding installation methods may be adapted for timber framed buildings, providing extra
care is taken in ensuring combustible materials are adequately protected from the effects of heat.
The appliance must be installed in accordance with the British Gas documents DM2 and DM3 or the Institute
of Gas Engineers published procedure document IGE/UP/7.
Special attention must be paid to the location of studwork frames of the inner leaf and the appliance positioned accordingly. Wires and pipes that run within the wall must also be taken into account.
IInnssttaallllaattiioonn aass ppeerr mmeetthhoodd 11 ((aaggaaiinnsstt iinnnneerr wwaallll))
When using this method of installation the following amendments should be incorporated.
50mm insulation must be provided between combustible materials and the sides and rear of the convector
box and the flue tube and 100 mm of insulation to the top of the convector box. It is also a good idea to
enable as much airflow into and out of the area behind the fire as possible without excessive heat losses when
1.0
1.0
Page 11
INSTALLATION METHOD 33 ((continued)
the fire is off. Where the flue pipe passes through the inner leaf, a hole 100mm larger in diameter than the flue
should be cut to allow an annular 50mm air gap around the flue circumference and a none combustible flue
sleeve must be fitted.
A layer of insulation material will be needed behind the cavity box, between the combustible wall and the 50
mm of rear insulation, to protect the inner leaf of the wall. A piece of 12 mm thick 'Supalux' or equivalent
should be fitted to do this. The vapour barrier on the back of the inner leaf should be cut and carefully pinned
to prevent any damp ingress.
IInnssttaallllaattiioonn aass ppeerr mmeetthhoodd 22 ((rreecceessssiinngg iinnttoo wwaallll))
When setting the appliance into the wall, find a suitable position between frame timbers and open up the
hole. Secure back the damp proof membrane to prevent ingress of damp. A drip collar of twisted galvanised
or stainless steel wire should be formed around the flue with twist on the underside of pipe to disperse drips
of water that may otherwise track back down the flue pipe to the appliance.
Again, 50mm insulation must be provided between combustible materials and the sides and rear of the convector box and the flue tube and 100 mm of insulation to the top of the convector box. The exposed cavity
should be sealed off using non-combustible board ('Supalux' or equivalent) made into a 4 sided box, rear, 2
sides and a top. Note that the appliance should not be allowed to bridge the cavity in this installation method.
FLUE PPREPARATION
When the preparation work for the chosen installation method has been completed and the fire surround (if
any) has been fitted, the flue can be prepared. The flue length calculation by measurement is quite straightforward but requires care and attention in getting an accurate result. Always double check to make sure the
measurement you have come up with is not too short - it is not possible to rejoin flue pipe cut off too short.
Always take into account that the whole terminal cage must project from the outside wall by its full 87.6mm
length.
Measure the distance between the front face of the marble or finished inner wall face that the fire is to be
mounted against, and the surface of the outside wall. Now deduct 100mm from that dimension and write it
down. This measurement is now the length that the flue must be cut to as measured from the end of the terminal cage (the very end of the duct) towards the other end of the duct that connects to the fire. Fit the support ring inside the flue pipe, mark off and cut the duct. The inner Flue duct must be cut at a length, which is
25mm longer as shown above
De-burr the cut ends of the flue pipe to allow a good connection to be made with the fire.
AALWAAYS BBE SSURE TTO RREMOVE TTHE PPOLYSTYRENE SSUPPORT RRING BBEFORE FFINAALLY FFITTING TTHE FFLUE
PIPE TTO TTHE FFIRE.
GAS SSUPPLY
When the opening is ready for installation of
the fire, the gas supply can be routed as shown
in the following diagram.
Temporarily fit the cavity box and offer up the
firebox assembly to ensure a suitable gas route
can be achieved.
FINAL CCAVITY BBOX FFITTING
If not previously carried out, insert the cavity box into the opening and mark the screw locations required for
fixing. Remove the cavity box and drill the previously marked holes in the opening or constructional hearth
area and fit rawl plugs.
Carefully insert the cavity box into the opening and guide the gas pipe through the sealing grommet into its
final routing position and fit the Restrictor inlet elbow supplied to the gas pipe. Secure the cavity box by inserting screws in the previously prepared locations.
The cavity box may also be fitted using the cable fixing kit supplied as detailed below.
1.0
1.0
1.0
1.0
Page 12
Page 13
Page 14
OPERATING TTHE AAPPLIANCE
The pilot is visible through the specially added hole in the left hand side of the
matrix. Push in and turn the control knob to the SPARK position, and hold there
for a few seconds.
Continue turning anti-clockwise through the spark click to the PILOT light position, ensuring the pilot has lit. If not, return the knob clockwise and repeat. When
the pilot lights after the spark, keep the knob depressed for approximately ten
seconds. Now release the knob and the pilot should stay alight.
If the pilot is extinguished during use of the fire, you MUST wait ten minutes
before repeating the ignition procedure.
To achieve the HIGH setting, push the control knob in slightly and continue tuning anti-clockwise to the high
position. The main burner should light after a few seconds. To decrease the setting to LOW, turn the control
knob clockwise to the low setting.
To turn to the PILOT position from the HIGH or LOW positions, press the control knob in slightly, and return
to the pilot position and release. To turn the fire OFF, keep the knob pressed in, return to the off position and
release. If the fire is switched off during use, ALWAYS wait 3 minutes for the fire to cool safely before attempting to relight. This ensures the safest condition for re-ignition.
SPARK FFAILURE
The gap between the spark electrode and the pilot should be 3 - 5mm to produce a good spark. There
should be no need to adjust this. If under any circumstances the piezo electric spark fails, the pilot cannot be
lit manually.
SETTING PPRESSURE
Remove the screw from the pressure test point,
situated on the main burner supply pipe just
underneath the front of the burner box area and
attach a U gauge. Light the fire on the HIGH setting.
The setting pressure should be in accordance
with the figures stated in the data section of
these instructions. The fire is factory set to
achieve these pressures and any significant variation could indicate a supply problem.If the pressure is too high, the gas supply meter may be set
incorrectly. This should be checked with the fire
running and if necessary reset by the gas supplier. If the setting pressure is too low, then check the meter governor pressure with the appliance running. If this is less than approximately 21mbar it will need to be reset by
the gas supplier. If the setting pressure is too low, but the meter pressure is acceptable, then a problem in the
supply pipework is to be suspected. This will be dirt and debris, kinked or inadequate size pipes, restriction in
a fitting, shut off elbow not fully open or solder flashing across a joint.
BRIEFING TTHE CCUSTOMER
All instructions must be handed to the user for safekeeping. Show the customer how to light and control the
fire.
After commissioning the appliance, the customer should be instructed on the safe use of the appliance and
the need for regular servicing. Frequency of service depends on usage, but MUST be carried out at least once
annually.
Advise that cleaning of the fire maybe achieved when the fire is cold using a damp cloth and mild detergent
on most surfaces.
Advise that the fire will emit a "newness" smell for a time after initial commissioning and that extra ventilation
may be needed during this time.
1.0
1.0
1.0
1.0
Page 15
BRIEFING THE CUSTOMER ((continued)
Explain that the fire does not use air from the room but ducts fresh air for combustion and exhaust gasses out
through the special flue system. The terminal of the flue system must not be allowed to have vegetation growing on or near and must also be kept well clear of any new buildings, sheds, conservatories etc that may be
built nearby. Any shielding or damage to the terminal or flue can cause severe damage to the fire and introduce a safety risk to the customer.
Recommend that a guard be used for the protection of the young, pets, the elderly and the infirm
SERVICING
Isolate the fire from the gas supply. Ensure that the fire is fully cold before attempting service. A suggested
procedure for servicing is detailed below.
1. Lay out the dust sheet and tools.
2. Remove the hood and front fret.
3. Remove the glass door assembly (4 screws) and clean carefully
4. Carefully remove the ceramic components.
5. Remove the screws that retain the data/control plate. (2 screws)
6. Remove front panel from firebox taking care not to damage sealing gasket.
7. Remove the 2 screws securing burner tray assembly into inner firebox and nuts on gasket
plate around gas pipe and undo gas pipe connection under burner box area. Lift away burner
tray assembly (tray and gas pipe).
8. Clean the injector, pilot assembly and the burner tube. Do not attempt to remove the pilot
injector as this can cause damage.
9. Re-assemble and re-fit the parts including the front panel - making sure that gasket is in good
condition.
10. Turn on the gas supply and leak test. Check pilot and burner for good ignition
11. Refit the ceramics, paying attention to the final layout as per installation section.
12. Refit the glass door assembly, ensuring a good seal.
13. Refit the hood.
14. Check the flue terminal for siting and clearance from vegetation etc
15. Light the fire and test setting pressures.
16. Check safe operation of the appliance.
For specific servicing instructions, see relevant sections.
CLEANING TTHE CCOALS
Remove the fire front casting and place to one side. Remove the hood. Remove the glass door assembly.
Remove the ceramic components. Gently clean in the open air. Be careful not to create dust from the coals.
Where necessary replace damaged components with genuine spares. Seal scrap ceramic components in plastic bags and dispose at proper refuse sites as directed. If using a vacuum cleaner, a HEPA filtering system is
recommended.
Re-fit the coals by referring to the relevant section of these instructions. Refit the glass door assembly ensuring a good seal. Refit the hood.
DISMANTLING AAND SSERVICING TTHE BBURNER TTRAY
Firstly, remove the hood and front fret, the glass panel, coals and ceramics, data/control plate, burner box
front panel, and disconnect the gas connection underneath the burner box area. Remove the burner tray itself
by removing the securing screws, releasing the seal around the incoming main burner pipe and lifting away.
The 2 screws securing the gas valve bracket should now be removed. The gas connections to the gas valve
can now be released and the valve brought forward to remove the thermocouple connection at the rear.
Remove the pilot and main burner pipes and blow through to dislodge any debris.
Remove the injector and blow through to make sure it is entirely clear. When replacing the injector elbow,
ensure that it aligned accurately with the centre of the mixer tube entering the burner and not at an angle.
Always make sure that the nut securing the injector elbow is tight. Clean the exterior of the pilot assembly
with a soft brush and blow through the flame ports on the pilot head. Check the aeration holes are free from
lint or dirt. The pilot assembly can be removed if required by disconnecting the electrode HT lead, gas pipe
and unscrewing the mounting screws and lifting away. The pilot assembly is a non-serviceable item and should
not be taken apart. Aeration holes must be absolutely clear internally for proper operation.
NEVER MMODIFY
OR BBEND TTHE TTHERMOCOUPLE TTO MMAAKE TTHE PPILOT SSTAAY AALIGHT.
1.0
1.0
1.0
1.0
Page 16
DISMANTLING AAND SSERVICING TTHE BBURNER TTRAY ((continued)
If the pilot will not stay lit there is a problem with dirt, the gas supply to it, the flue connection or termination,
or the thermocouple needs replacement. Modifications are dangerous and can have a serious unseen effect
on safety. The integral gas valve pilot filter can be removed and cleaned as follows. Remove the control knob
by pulling it forwards, then remove the largest of the three screws on the face of the valve. Slide the filter out
and clean away any debris that may have accumulated. The filter element should also be blown clean. This
component should not require replacement, however if signs of deterioration are evident then a genuine spare
must be used. If a large amount of debris is present in the filter then the pipework and control should be thoroughly cleaned before re-assembly.
Re-assembly is the reverse of removal.
REMOVING TTHE FFIREBOX
Remove all loose parts such as brass frame, hood and fret. Remove the glass panel and ceramics from the firebox. Isolate and disconnect the gas supply at the gas valve. Remove the firebox to cavity box fixings and any
seal around the flue pipe where it passes through the outside wall. The firebox should now be free to be lifted
out.
Refit the firebox as described in the fitting section of these instructions.
PILOT AASSEMBLY
Remove the hood, glass panel, ceramics and burner tray as described in the section dealing with the burner
tray and gas assembly. The pilot can now be accessed easily for cleaning or removal. If removing, take care
not to damage the gasket.
Clean the pilot assembly with a soft brush and blow through. Check the aeration holes are free of any dirt or
lint. Clean thoroughly internally, the connection can be removed from the base of the pilot unit using two
spanners to make cleaning easier. Do not damage or try to remove the pilot injector.
NEVER MMODIFY OOR BBEND TTHE TTHERMOCOUPLE TTO MMAAKE TTHE PPILOT SSTAAY AALIGHT.
If the pilot will not stay lit there is a problem with dirt, the gas supply, flue termination or connection, or the
thermocouple needs replacement. Modifications are dangerous and can have a serious unseen effect on safety.
The unit is factory set and the only check necessary is to ensure the spark gap is correct and that no damage
has occurred to the unit.
TESTING FFOR FFIREBOX LLEAKAGE
The firebox is tested in production for soundness to the required standard. New appliances should present no
problem in this regard, however appliances that are several years old or have been extensively dismantled
should be checked for soundness. The firebox can be field tested for soundness or leakage by two main methods.
A. SMOKE TESTING. The firebox is heated by lighting for a few minutes to provide a flow through the
firebox and flue. The burner is then shut off and the firebox is opened and a smoke pellet introduced
or smoke is introduced to the air intake (outer) duct of the flue terminal. Large quantities of smoke
emerging from the appliance at joints or gasket faces indicate where major leaks may be occurring. It
is important to note that the appliance can never be expected to be 100% smoke tight and small
quantities of smoke may be seen in corners of joints and gasket faces etc without affecting safety
when the fire is actually in operation.
B. GAS SAMPLING. This is done with a CO/CO2 analyser with the fire running. Samples of the con
vection air and room air are taken before and after the fire is lit to ascertain if the fire is leaking com
bustion products at significant levels. It is important to note that sampling with a probe right next to a
joint or gasket face is not a reliable test, as the action of the analyser sucking and locally high concen
trations of gas will significantly affect the reliability of readings. The important point to note is whether
there is a significant increase in ambient CO/CO2 in the room air after 15 to 30 minutes operating. A
small or negligible increase indicates insignificant leakage rates. A significant increase warrants further
inspection and testing with smoke as described above to isolate and eliminate leaks.
1.0
1.0
1.0
1.0
Page 17
TROUBLESHOOTING GGUIDE
No gas to fire, check isolators are open.
Pipework blockage, clean out.
Air not fully purged, re purge supply or wait longer.
Spark earthing to metal work, reset gap correctly.
Blocked pilot, clean out internally.
Severe restriction in gas supply: clear obstruction.
Faulty thermocouple, replace pilot unit.
Blocked pilot, clean out. Hold control knob in for longer.
Check control knob does not foul data plate.
Flue disconnected or connection damaged, partly or fully blocked, terminal
obscured or damaged.
NEVER MMODIFY OOR BBEND TTHE TTHERMOCOUPLE TTO MMAAKE TTHE PPILOT
STAAY AALIGHT
. If the pilot will not stay lit there is a problem with dirt, the
gas supply, flue termination or connection, or the thermocouple needs
replacement. Modifications are dangerous and can have a serious unseen
effect on safety.
Fire does not spark at pilot
HT lead detached, refit.
Spark gap too large or small, reset correctly.
Faulty piezo unit, replace.
Debris shorting out electrode, clean.
Spark shorting to metalwork under tray, realign HT lead.
Fire runs for a time and then cuts off
Loose or faulty thermocouple, rectify.
Blocked pilot, clean out.
Dirt or lint in pilot aeration hole, clean thoroughly internally.
Flue disconnected or connection damaged, partly or fully blocked, terminal
obscured or damaged.
NEVER MMODIFY OOR BBEND TTHE TTHERMOCOUPLE
TO MMAAKE TTHE PPILOT SSTAAY AALIGHT
. If the pilot will not stay lit there is a
problem with dirt, the gas supply, flue termination or connection, or the
thermocouple needs replacement. Modifications are dangerous and can
have a serious unseen effect on safety.
Poor gas flow to fire, check pressure with fire on high.
If pressure is low, remove any restriction in pipework or valve.
Check all isolators are adequately sized and fully open.
Check meter pressure is adequate.
Flue disconnected or connection damaged, partly or fully blocked, terminal
obscured or damaged.
NEVER MMODIFY OOR BBEND TTHE TTHERMOCOUPLE
TO MMAAKE TTHE PPILOT SSTAAY AALIGHT
. If the pilot will not stay lit there is a
problem with dirt, the gas supply, flue termination or connection, or the
thermocouple needs replacement. Modifications are dangerous and can
have a serious unseen effect on safety.
Newness smell from brand new appliance.
Leakage occurring. Carry out leakage test and rectify any problems.
Low temperature sealants or combustible materials used in incorrect
positions.
Fire ssparkss bbut ppilot
doess nnot lligght
Fire rrunss ffor aa ttime
and tthen ccutss ooff
Pilot lligght bbut tthen
ggoess oout
Fire ddoess nnot sspark aat
pilot
Pilot fflame sshrinkss
when ffire iiss oon hhiggh
Fire ssmellss wwhen ffirsst
lit
1.0
Page 18
UUSSEERR IINNSSTTRRUUCCTTIIOONNSS
IMPORTANT NNOTES
The installation and Servicing of this fire MUST only be carried out by a competent person (such as a CORGI
registered fitter) in accordance with the Gas Safety (Installation and Use) Regulations 1998, the relevant British
Standards, Codes of Practice, the Building Regulations and the manufacturer's instructions.
Failure to comply with the above recommendations could lead to prosecution and invalidate the appliance
warranty.
Please ensure you are handed all of the manufacturers documents on completion of the installation. This will
include these instructions.
Always keep a note of the installer's name and address, the original purchase receipt and the date of installation for future reference.
The fire and flue should be serviced regularly to ensure continued safe operation. See the servicing section
for further reference.
Parts of this appliance become naturally hot during use. It is recommended that a suitable fire guard conforming to BS 6778 or BS 6539 is used, especially where young children, pets, the elderly or infirm are concerned.
The manufacturer of this appliance considers all surfaces as working surfaces with the exception of the control
knob, control panel and ash pan cover.
Combustible items, such as flooring and furniture and soft wall coverings (such as blown vinyl or embossed
paper), low temperature surrounds etc may discolour if fitted too close to the fire. See relevant section for further details on clearances to combustibles. No combustible materials or flooring should protrude onto the
hearth.
DO NOT burn any foreign material on this fire, the coals must be of the correct type and laid out in accordance with the relevant section of the these instructions. Failure to do so may create a hazard or lead to sooting. Under no circumstances shall the appliance be used if the glass front door or panel has been, removed or
is open.
The integral appliance flue should be checked by the installer upon servicing to ensure there are no defects or
obstructions that may prevent the satisfactory flow of combustion products.
This appliance is only suitable for the gas type for which it is supplied.
FIREFRONT
This fire is supplied with a particular style of fire front. Use of the fire front will ensure an adequate airflow
under the firebox for the correct efficiency and control temperatures of this appliance. Whilst other fronts can
be used, compliance with temperature standards cannot be guaranteed when another style of front is used.
Secction Contentss Pagge NNo.
1.0 Important NNotes
1
2.0 Firefront
1
3.0 Clearance tto CCombustibles
2
4.0 Ventilation
2
5.0 Operating IInstructions
2
6.0 Cleaning
2
7.0 Coals aand CCeramics
3
8.0 Servicing
3
9.0 List oof SSpare PParts
3
1.0
1.0
Page 19
CLEARANCES TTO CCOMBUSTIBLES
A non-combustible shelf may be fitted to within 100mm of the top edge of the fire frame. However the items
placed on it must also be able to withstand high temperatures.
A combustible shelf may be fixed to the wall above the fire, providing that is complies with the dimensions
given below.
Combustible materials, such as wood, may be fitted to within 100mm (4in) of either side of the frame of the
appliance, providing the forward projection does not exceed 100mm (4in).
Any combustible side walls must be at least 500mm to the side of the radiant heat source.
As with all heating appliances, any decorations, soft furnishings and wall coverings (i.e. flock, blown vinyl and
embossed paper) positioned too close to the appliance may discolour or scorch.
VENTILATION
No purpose provided ventilation is required for this appliance because it is room sealed. The requirements of
other open flued appliances operating in the same room or space must be taken into consideration when
assessing ventilation.
The combustion air supply for this appliance is ducted from the outside air by an integral flue system. The terminal of this flue system must always be kept clear of vegetation, new buildings, conservatories, extensions,
sheds or other potential obstructions and able to perform its function correctly. A supply of fresh air into the
room is advisable to maintain temperatures within limits.
For Republic of Ireland, see relevant rules in force.
OPERATING IINSTRUCTIONS
The pilot is visible through the small hole in the left hand side of the matrix
base. Push in and turn the control knob to the SPARK position, and hold
there for a few seconds.
Continue turning anti-clockwise through the spark click to the PILOT light
position, ensuring the pilot has lit. If not, return the knob clockwise and
repeat.
When the pilot lights after the spark, keep the knob depressed for approximately ten seconds. Now release the knob and the pilot should stay alight.
If the pilot is extinguished during use of the fire, you MUST wait three minutes before repeating the ignition procedure.
To achieve the HIGH setting, push the control knob in slightly and continue tuning anti-clockwise to the high
position. The main burner should light after a few seconds. To decrease the setting to LOW, turn the control
knob clockwise to the low setting.
To turn to the PILOT position from the HIGH or LOW positions, press the control knob in slightly, and return
to the pilot position and release. To turn the fire OFF, keep the knob pressed in, return to the off position and
release. If the fire is switched off during use, ALWAYS wait 3 minutes for the fire to cool safely before attempting to relight. This ensures the safest condition for re-ignition.
To turn the fire OFF, keep the knob pressed in, return to the off position and release.
CLEANING
Before carrying out any of the following operations, ensure that the fire is OFF and completely cold.
Debris that may form on the fire bed should be periodically removed by a competent person. Large deposits
could indicate flue problems or incorrect coal placement. This should be repaired by a competent person and
the fire serviced before further use. To gain access to the fire bed, remove the hood and glass door assembly.
Maximum depth of shelf Minimum distance from hearth to underside of shelf
180mm 850mm
1.0
1.0
1.0
1.0
Page 20
The hood should be lifted and pulled outwards to disengage, then remove the door by removing the four
screws and lifting away. The glass can be cleaned with a suitable glass cleaner.
FIREFRONT - Any dust accumulating in the fire front may be removed using a vacuum cleaner or dry cloth.
Heavy stains may be removed by using a damp cloth and mild household detergent. Brass parts
of the fire front may be cleaned using a suitable brass cleaner. Replace the front centrally
against the fire after cleaning.
PAINTED AREAS - These can be cleaned using a dry cloth.
COALS AAND CCERAMICS
See the relevant section in the Installation Guide of these instructions. Clean coals gently in open air. Do not
create dust from the coals. If using a vacuum cleaner, a HEPA filter system is recommended.
SERVICING
The fire and flue should be checked on an annual basis to it is working safely and that there is no excessive
build up of soot. The frequency of service will depend on usage, but MUST be carried out at least once annually. Servicing must be carried out by a competent person, such as a CORGI registered installer.
Cleaning of the coals may be carried out by following the instructions given in the Installation section. The
Installation instructions carry full servicing details for the use of the installer.
LIST OOF SSPARE PPARTS
PAART NNO. ITEM
?????????? Pack of 14 coals
?????????? Ceramic combustion matrix
?????????? Ceramic side cheeks
?????????? Ceramic brick panel
Please enquire Decorative frame
Please enquire Decorative fret
?????????? Glass door assembly
Please enquire Hood
?????????? Pilot assembly
?????????? Gas valve
?????????? Burner tray
?????????? Pilot Gasket
?????????? Gas pipe gasket
?????????? Front panel gasket
????????? Outer tray gasket
1.0
1.0
1.0
1.0
Loading...