Focal FPD 600.4 Operation Configuration

Page 1
FPD 600.4 : FOUR CHANNEL AMPLIFIER Operation / Configuration
POWER PER CHANNEL:
4 X 150W into 4 ohm
4 X 200W into 2 ohm
Two amplifiers can be Bridged 2 X 400W into 4 Ohm
Two amplifiers can be Bridged 2 Ohms - NO
ROUTE SWITCH
1+2 = All four RCA inputs are used.
Recommended when bridging channels 1, 2, 3, 4. The level controls still function.
Copy = Input signal and filters on channels 3+4 are copied to channels 1+2. Use this mode when you need a band pass filter on all four channels. Recommended when bridging channels 1,2,3,4. The level controls still function.
CHANNELS 1 & 2 CROSSOVER CONFIGURATION
Flat: Full Range Signal. No crossover filter used.
HP: Activates the High Pass Filter for a midbass or tweeter.
CHANNELS 3 & 4 CROSSOVER CONFIGURATION
Flat: Full Range Signal. No crossover filter used.
HP: Activates the High Pass filter.
LP/BP: Activates the selection of either a Low Pass filter for woofer or a Band Pass filter for midrange.
MONO Mode: Inputs 3+4 are mixed to mono for bridge mode operation. If 1+2 ROUTE is set to COPY then 1+2 will also be mono subwoofer and the remote volume control will control level. The subwoofer remote volume control is activated. There is a clip distortion light on the remote volume control. If you see this light on, reduce volume until the light goes out so that you do not damage your speaker.
AUTOMATIC POWER TURN ON/OFF
1. The best way to automatically turn the amplifier power on and off is to use the REM wire from your source radio connected to the REM amplifier terminal.Band Pass for a subwoofer or midbass of a 3 way speaker.
2. If your original equipment stereo or source radio has a BTL amplifier then the RCA inputs have an auto turn on sensing circuit. When you connect the high level BTL speaker wires to the RCA input the REM wire is not necessary.
1
Page 2
RCA INPUT, BOTH LOW LEVEL AND HIGH LEVEL.
The amplifier LEVEL control has sufficient adjustment range for both low level and high level input into the RCA jacks. A factory source radio that does not have RCA output, using the wires that are connected to the speakers,
can be directly connected to the RCA jacks when the amplifier LEVEL control is adjusted to 8V.
SETTING LEVEL
Set the amplifier LEVEL control to minimum before you turn on the amplifier for the first time.
For lowest distortion and lowest noise the amplifier LEVEL should be set at the lowest setting that yields sufficient loudness without distortion. For lowest noise your source radio volume control should be near maximum that does not cause distortion.
To find the best amplifier LEVEL setting: With the amplifier LEVEL at minimum, slowly increase the source radio volume to around 3/4 without distortion. Then, slowly turn up the amplifier LEVEL control to the maximum desired loudness. Listen very carefully and turn down the amplifier LEVEL control if you hear any distortion.
FPD 600.4 CONFIGURATION EXAMPLES
4 CHANNEL STEREO NON-BRIDGED
If you have four input wires from the source deck, plug them into inputs 1+2 and 3+4. Set ROUTE switch to 1+2.
If you have two input wires from the source deck, plug them into inputs 3+4. Set ROUTE switch to 3+4. Set the switch to STEREO.
If you are NOT using a subwoofer set all switches to flat. If you hear distortion in your woofers set all switch to HP and adjust all HP frequency until the distortion goes away, this will probably be around 50 Hz to 70 Hz.
2
Page 3
B1
RADIO
1
2
FLAT or HP50Hz
BP
3
110
70
50
4
240
240
600
110
1K3
70
4K
50
LP
HP
240
110
70
HP
50
LP
600
1K3
4K
HP
650
1K3
4K
FLAT
HP
COPY
FLATLP/BP
3+4
ROUTE
STEREO
S T
M
E
O
R
N
E
O
O
1+2
CH 3+4
LEVEL
8v
CH 1+2
LEVEL
8v
BRIDGE
+
+
0.2v
SUB CONTROL
CH 2
0.2v
CH 1
XOVER XOVERXOVER XOVER
BRIDGE
+
+
CH 4
CH 3
GND
REM
BATT
1+250Hz FLAT or HP
B1 <GRAPHIC of Source Radio to input channel 1+2, 3+4 of amplifier. Woofer/Tweeter/Xover on channels 1+2, 3+4>
IF YOU ARE USING TWO SUBWOOFERS:
Put your woofer/tweeters on channel 1+2.
Set 1+2 switch to HP. Adjust 1+2 HP frequency to 50 Hz.
Subwoofers on channel 3+4. Set 3+4 switch to LP/BP. Set 3+4 switch to LP. Adjust 3+4 LP frequency to 50 Hz. Set the switch to MONO. Plug in the remote sub control.
3
Page 4
B2
RADIO
SUBWOOFER
+–
LP LP/BP50Hz
MONO
XOVER XOVER
SUBWOOFER
+–
HP
LP/BP
FLAT
COPY
FLAT
3+4
ROUTE
1
3
2
4
240
600
110
110
1K3
70
70
4K
50
50
HP
110
70
HP
50
BP LP
240
600
1K3
4K
LP
240
HP
650
1K3
4K
3+450Hz HP
CH 3+4
S T
M O N O
LEVEL
E R E O
0.2v
8v
CH 1+2
1+2
LEVEL
0.2v
8v
REMOTE SUB CONTROL
SUB CONTROL
+
CH 1
BRIDGE
+
CH 2
BRIDGE
+
+
CH 4
CH 3
GND
REM
B2 <GRAPHIC of Source Radio to input channel 3+4 of amplifier. Woofer/Tweeter/Xover on channels 1+2, one
3 CHANNEL WITH BRIDGED SUBWOOFER
If you have four input wires from the source deck plug them into inputs 1+2 and 3+4. Set ROUTE switch to 1+2.
If you have two input wires from the source deck plug them into inputs 3+4. Set ROUTE switch to 3+4.
Put your woofer/tweeters on channel 1+2. Set 1+2 switch to HP. Adjust 1+2 HP frequency to 50 Hz.
BATT
Your subwoofer is wired to channel 3+ and channel 4-. Set 3+4 switch to LP/BP. Set 3+4 switch to LP. Adjust 3+4 LP frequency to 50 Hz. Set the switch to MONO. Plug in the remote sub control.
4
Page 5
B3
RADIO
50Hz
LP
LP/BP
MONO
XOVER XOVER
SUBWOOFER
+–
HP
LP/BP
FLAT
COPY
FLAT
3+4
ROUTE
1
3
2
4
240
600
110
110
1K3
70
70
4K
50
50
HP
110
70
HP
50
BP LP
240
600
1K3
4K
LP
240
HP
650
1K3
4K
3+450Hz HP
CH 3+4
S T
M O N O
LEVEL
E R E O
0.2v
8v
CH 1+2
1+2
LEVEL
0.2v
8v
REMOTE SUB CONTROL
SUB CONTROL
+
CH 1
BRIDGE
+
CH 2
BRIDGE
+
+
CH 4
CH 3
GND
REM
BATT
B3 <GRAPHIC of Source Radio to input channel 3+4 of amplifier. Woofer/Tweeter/Xover on channels 1+2, one subwoofer wired to channel 3+ and channel 4->
BIAMP A WOOFER AND TWEETER
Connect the source deck front channel wires into inputs 3+4.
Set ROUTE switch to 3+4.
Set the switch to STEREO.
Connect your tweeters to channels 1+2. Set 1+2 switch to HP. Adjust 1+2 HP frequency to the tweeter manufactures recommendation. 3500 Hz is a good starting point.
Connect your woofers to channels 3+4. Set 3+4 switch to LP/BP.
If you are NOT using a subwoofer set the 3+4 switch to LP. Adjust the 3+4 LP frequency to the manufactures recommendation. 3500 Hz is a good starting point. If you hear distortion in your woofers set channel 3+4 switch to BP and adjust the 3+4 HP frequency to 50 Hz.
If you ARE using a subwoofer on a separate amplifier then set channel 3+4 switch to BP and adjust the 3+4 HP frequency to 50 Hz.
5
Page 6
B4
RADIO
WOOFER
TWEETER
BP LP/BP50Hz 3.5K
STEREO
TWEETER
WOOFER
HP
LP/BP
FLAT
COPY
FLAT
3+4
ROUTE
1
3
2
4
240
600
110
110
1K3
70
70
4K
50
50
HP
110
70
HP
50
BP LP
240
600
1K3
4K
LP
240
HP
650
1K3
4K
3+43.5K HP
CH 3+4
S T
M O N O
LEVEL
E R E O
0.2v
8v
CH 1+2
1+2
LEVEL
0.2v
8v
REMOTE SUB CONTROL
SUB CONTROL
+
CH 1
BRIDGE
+
CH 2
BRIDGE
+
+
CH 4
CH 3
GND
REM
BATT
B4 <GRAPHIC of Source Radio to input channel 3+4 of amplifier. Tweeter on channels 1+2. Woofer on channels 3+4>
TROUBLESHOOTING:
> FOCAL SIGN DOES NOT LIGHT
1. Measure the voltage at the amplifier power terminal. It should be between 12 and 15 volts.
2. Measure the voltage at the amplifier REM terminal. It should be between 12 and 15 volts.
3. If you are using BTL high level for automatic turn on, try connecting a REM wire.
4. Check your power and ground connections to be correct polarity + and - and they are tight.
5. Check battery connections.
6. Check the fuse in the REM wire.
7. Check fuse at battery.
8. Check fuse inside amplifier.
The fuse is inside the right end cap beside the power terminals. The recommended ATC fuse size is two 25 amp.
> FOCAL SIGN IS FLASHING
1. Is the amp very hot? Wait a few minutes for it to cool down. You need to get more fresh cool air to the amplifier. Do not cover the amplifier or mount it flush into a hole.
2. If the amp is cold and the Focal sign is flashing, there is an internal fault. The amplifier must then be returned for service.
6
Page 7
> NO SOUND
1. Is the Focal sign light off or flashing?
2. Is the source radio on and is there a sound signal coming from the source radio?
3. Use an ohm meter and measure the speaker wires for short circuit.
4. Check connections for small “wire whisker” that may be shorting between amplifier terminals or speaker terminals.
5. Use an ohm meter and measure the speaker for short circuit.
6. Double check your connections to the source radio.
7. Are you using the correct source radio wires and are they plugged into the correct amplifier RCA?
8. Double check your connections to the speakers and speaker crossovers.
9. Check that all amplifier switches are in the correct positions for your speaker set up.
> AMPLIFIER BLOWS FUSE WHEN YOU TURN IT ON.
1. Power and ground may be reversed.
Check + and - polarity at amplifier and at battery.
> SUBWOOFER REMOTE VOLUME CONTROL DOES NOT FUNCTION.
1. Check that Remote Volume Control wire is plugged into the amplifier securely.
2. The Remote Volume Control will not function if the amplifier switch is “DIRECT”. The switch must be in “MASTER”.
> SUBWOOFER REMOTE VOLUME CONTROL LED LIGHT.
1. While playing music the LED light should be Green. Occasional red LED light flash indicates that the amplifier has reached maximum loudness.
2. If the red LED light flashes with the beat of the music, TURN DOWN THE VOLUME before you damage your speaker.
3. If the red LED light is on continuous, TURN DOWN THE VOLUME before you damage your speaker.
WARRANTY REGISTRATION CARD
7
Loading...