Focal 923 User Manual

Download

Page 1

Focal Technologies Corporation

A Moog Inc. Company 77 Frazee Avenue Dartmouth, Nova Scotia, Canada B3B 1Z4 Tel: (902)468-2263 | www.moog.com/focal

Document No.:

923-0603-01

Revision:

Author(s):

R.Sawler

Date of Issue:

2017-04-24

Model 923

Data Logger

User Manual

MOOG PROPRIETARY AND CONFIDENTIAL INFORMATION

THIS TECHNICAL DATA/DRAWING/DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO, AND IS THE EXPRESS PROPERTY OF MOOG INC., OR MOOG INC. SUBSIDIARIES EXCEPT AS EXPRESSLY GRANTED BY CONTRACT OR BY OPERATION OF LAW AND IS RESTRICTED TO USE BY ONLY MOOG EMPLOYEES AND OTHER PERSONS AUTHORIZED IN WRITING BY MOOG OR AS EXPRESSLY GRANTED BY CONTRACT OR BY OPERATION OF LAW. NO PORTION OF THIS DATA/DRAWING/DOCUMENT SHALL BE REPRODUCED OR DISCLOSED OR COPIED OR FURNISHED IN WHOLE OR IN PART TO OTHERS OR USED BY OTHERS FOR ANY PURPOSE WHATSOEVER EXCEPT AS SPECIFICALLY AUTHORIZED IN WRITING

BY MOOG INC. OR MOOG INC. SUBSIDIARY.

Page 2

Model 923 Data Logger – User Manual

Document

Revision

Details of Revision

Author(s)

Date

[yyyy-mm-dd]

Rev 1

Initial release.

A. Cabrera

2015-08-10

Rev 2

-Updated title page, headers and footers

-Change all references of 4 analog channels to 2

-Update GUI images

-Update board images to Rev4.0

-Update Analog Inputs section for 2 channel description

-Add Adjustable Analog Input display to special features

-Updated Serial Output Mode in Modbus table to show only Modbus RTU is supported

R. Sawler

2017-04-24

Document Number

Document Title and Description

923-2004-00

Model 923 Data Logger Configuration Drawing

Document Revision History

Reference Documents

Focal Technologies Corporation Page ii A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 3

Model 923 Data Logger – User Manual

TABLE OF CONTENTS

1.0 Introduction........................................................................................................................................... 1-1

2.0 Specifications ....................................................................................................................................... 2-1

3.0 Product Description ............................................................................................................................. 3-1

3.1 Configuration Settings and Initial User Setup ............................................................................... 3-2

3.1.1 Configuration Settings ..................................................................................................... 3-2

3.1.2 Initial User Setup ............................................................................................................. 3-3

3.2 Data Logging ................................................................................................................................ 3-3

3.3 Real Time Clock (RTC) ................................................................................................................ 3-3

3.4 On-Board Sensors ........................................................................................................................ 3-4

3.4.1 Temperature and Humidity Sensor ................................................................................. 3-4

3.4.2 3-Axis Accelerometer Sensor (Shock and Vibration) ...................................................... 3-4

3.4.3 Ambient Light Sensor ...................................................................................................... 3-4

3.4.4 Rotation Sensor (Turns Counter and Speed) .................................................................. 3-4

3.5 Interfaces ...................................................................................................................................... 3-5

3.5.1 Thermocouple Inputs ....................................................................................................... 3-5

3.5.2 Analog Inputs ................................................................................................................... 3-5

4.0 Hardware ............................................................................................................................................... 4-1

4.1 General Board Handling ............................................................................................................... 4-1

5.0 Electrical Connectors and Pin Descriptions ..................................................................................... 5-1

5.1 9-pin Micro-D Power and Data Connector (J5) ............................................................................ 5-1

5.2 Thermocouple Input Connectors (J6, J15) ................................................................................... 5-1

5.3 12-Pin Analog Input Connector (J4) ............................................................................................. 5-2

6.0 Functionality ......................................................................................................................................... 6-1

6.1 Serial Diagnostic Interface ............................................................................................................ 6-1

6.1.1 Modbus RTU ................................................................................................................... 6-1

6.2 Diagnostics Software .................................................................................................................... 6-2

6.2.1 Overview .......................................................................................................................... 6-2

6.2.2 Installation........................................................................................................................ 6-3

6.2.3 Application Usage ............................................................................................................ 6-3

6.2.4 Special Features .............................................................................................................. 6-5

7.0 Register Maps ....................................................................................................................................... 7-1

7.1 Modbus RTU Register Map .......................................................................................................... 7-1

7.1.1 On-board Sensor Registers ............................................................................................. 7-4

7.1.2 Sensor Data Conversion ................................................................................................. 7-5

Focal Technologies Corporation Page iii

A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 4

Model 923 Data Logger – User Manual

LIST OF TABLES

Table 2-1: Specifications .................................................................................................................................... 2-1

Table 3-1: Factory Default Card Configuration Settings (as-built) ..................................................................... 3-2

Table 5-1: Connector/Mating Connector Part Numbers .................................................................................... 5-1

Table 5-2: Micro-D (9-pin) Connector (J5) Pin out ............................................................................................. 5-1

Table 5-3: Thermocouple Input (3-pin) Connector (J6, J15) Pinout .................................................................. 5-1

Table 5-4: Analog Input (12-pin) Connector (J4) Pin out ................................................................................... 5-2

Table 6-1: Modbus RTU Frame Format and 923-EDL Defaults ........................................................................ 6-1

LIST OF FIGURES

Figure 1-1: Model 923 Electronic Data Logger Card ......................................................................................... 1-1

Figure 3-1: Model 923-EDL Part Locations ........................................................................................................ 3-1

Figure 3-2: Model 923-EDL Typical Setup Connection Using a PC and Focal GUI .......................................... 3-3

Figure 4-1: Model 923-EDL PCBA ..................................................................................................................... 4-1

Figure 5-1: Micro-D (9-pin) Power & Data Connector (J5) ................................................................................ 5-1

Figure 5-2: Thermocouple Input Connectors (J6, J15) ...................................................................................... 5-1

Figure 5-3: 12-pin Analog Input Connector (J4) ................................................................................................ 5-2

Figure 6-1: 923-GUI ........................................................................................................................................... 6-2

Figure 6-2: Connection Manager ....................................................................................................................... 6-3

Figure 6-3: Add a New Data Logger Configuration ............................................................................................ 6-4

Figure 6-4: 923-GUI – Reading the Data from Flash (Internal Log) .................................................................. 6-5

Figure 6-5: 923-GUI – File Read-back Function (Load Log) ............................................................................. 6-8

Figure 6-6: 923-GUI – Alarm Configuration ....................................................................................................... 6-9

Figure 6-7: 923-GUI – Time Synchronization of 923-EDL RTC’s with PC ...................................................... 6-10

Figure 6-8: 923-GUI – ADC Controls ............................................................................................................... 6-11

Figure 6-9: 923-GUI – Adjusted Analog Input .................................................................................................. 6-11

Focal Technologies Corporation Page iv

A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 5

Model 923 Data Logger – User Manual

ADC

Analog to Digital Converter

CRC

Cyclic Redundancy Check

ECL

Emitter Coupled Logic (Vcc = 0V)

EIA

Electronic Industries Association

ESD

Electrostatic Discharge

ESR

Electrical Slip Ring

FORJ

Fiber Optic Rotary Joint

FPSO

Floating Production, Storage and Offloading

HUMS

Health and Usage Monitoring System

I/O

Input/output

Integrated Circuit

kbps

Kilobits Per Second

LED

Light Emitting Diode

Megabytes

Mbps

Megabits Per Second

NRZ

Non-Return to Zero (bit signaling format)

PCB

Printed Circuit Board

PCBA

Printed Circuit Board Assembly

PECL

Positive Emitter Coupled Logic (Vcc = +5 V)

P/N

Part Number

RPM

Revolutions Per Minute

SMT

Surface Mount Technology

SPI

Serial Peripheral Interface

TDM

Time Division Multiplexer / Multiplexing

TTL

Transistor-Transistor Logic

UART

Universal Asynchronous Receiver/Transmitter

Microcontroller

ACRONYMS AND ABBREVIATIONS

Focal Technologies Corporation Page v A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 6

Model 923 Data Logger – User Manual

This user’s manual and the appropriate reference documents should be reviewed prior to

installation or reconfiguration of the data logger system. Refer to system installation drawings and Model 923 configuration drawings for specific installation details.

1.0 Introduction

The Model 923 electronic data logger (923-EDL) is a compact and rugged data logging card used for product health monitoring in marine, industrial, and other harsh environments. When installed as an option in Focal

systems such as electrical slip rings (ESRs) and FPSOs, it provides real-time access to diagnostic information as well as data storage for offloading at a later time. Typically mounted at the end of a ring stack, the 923-EDL collects data from an array of on-board sensors and stores it in nonvolatile flash memory.

The 923-EDL on-board sensors are capable of measuring temperature, relative humidity, ambient light, shock, vibration and rotation. Logging the total number of slip ring rotations allows tracking of slip ring usage for better

planning of maintenance intervals. The environmental data collected can be used to establish baseline operational parameters and trend monitoring can be used in a health and usage monitoring system (HUMS) to identify potential problems before they become major faults. In addition to the on-board sensors, the 923-EDL

provides expansion connectors that can be used to interface with up to two (2) thermocouples and up to two (2) single-ended analog channels.

Users can access on-board diagnostic information in real time via an RS-485 serial link using the sample FocalTM graphical user interface (GUI) software (based on the Microsoft® .NET Framework), or by using custom software

configured as a Modbus RTU master device (e.g. ModScan32). A top view of the Model 923-EDL card is shown below.

Figure 1-1: Model 923 Electronic Data Logger Card

Focal Technologies Corporation Page 1-1 A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 7

Model 923 Data Logger – User Manual

ENVIRONMENTAL

VALUE

COMMENTS

Operating Temperature

-20°C to +70°C

Storage Temperature

-40°C to +85°C

Shock

30 g, 11 ms

Per ISO 13628-6 Q1 level

Vibration

5 g, 25 - 1000 Hz

Per ISO 13628-6 Q1 level

Humidity

5-95% RH

Non-condensing

MECHANICAL

Dimensions

3.37” [86 mm] (NOM)

External diameter

Mounting

4 x #2 screw holes

Use with #2-56 standoffs

Weight

< 40 grams

ELECTRICAL

Input Voltage

+15 to +30 VDC

+24 VDC nominal Optional: +5 or +12 VDC (contact factory for details)

Current Draw

0.04 A (TYP)

With 24 VDC input

Power Dissipation

1.0 W (NOM), 2.0 W (MAX)

Overvoltage Protection

36 VDC

Reverse Polarity Protection

36 VDC

Battery

3.3V lithium-Ion rechargeable

For real-time clock only

SENSORS

Temperature Sensor

-40°C to +100°C

Accuracy +/- 1 °C

Humidity Sensor

5 - 95 % RH

Light Sensor

λ = 300 to 1000 nm

Wavelength range

3-axis Accelerometer

+/- 200 g

Rotation Sensor

Direction (CW, CCW), speed (rpm) and total revolutions

Real Time Clock Accuracy

+/- 5 ppm

Logging Flash Memory Size

32 MB

14 years logging at 60 min log interval

Thermocouple

-40°C to +100°C

K-type thermocouple

4 x Analog Input

0 to +3 VDC

10 bit, 200 Hz sampling

INTERFACES

Diagnostic and control

2-wire RS-485 serial interface with ISO ground

115.2 Kbaud, Modbus RTU

2.0 Specifications

Table 2-1: Specifications

Focal Technologies Corporation Page 2-1 A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 8

Model 923 Data Logger – User Manual

REF.

DESCRIPTION (CONNECTORS)

1 x 12-PIN CONN. FOR 2 x ANALOG INPUTS (SINGLE-ENDED)

1 x 9-PIN MICRO-D CONNECTOR FOR POWER AND DIAGNOSTICS (RS-485)

J6, J15

2 x 3 PIN THERMOCOUPLE INTERFACES

J3, J7,

J10

FACTORY USE ONLY

REF.

DESCRIPTION (OTHERS)

3.3V LITHIUM-ION RECHARGEABLE BATTERY

SW1,

SW2

FACTORY USE ONLY

3.0 Product Description

The 923-EDL card provides an array of on-board sensors and interfaces for external sensors. The card is typically installed at the factory inside FocalTM rotary products such as ESRs and FPSOs. With power applied to the 923-EDL, sensor data is logged automatically to on-board flash memory and simultaneously available in real time via an RS-485 serial link (J5) to a remote location. Key part locations are shown below.

Focal Technologies Corporation Page 3-1

A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Figure 3-1: Model 923-EDL Part Locations

Page 9

Model 923 Data Logger – User Manual

Name

Parameter

Default Setting

Diagnostics Port (J5) (Hardware)

Serial

Interface

RS-485

Termination

On-board 120 ohm Terminator Enabled / Disabled

120 ohm terminator enabled (installed)

On-Board Dip Switches SW1/2 (Hardware)

SW1

Data port serial protocol

RS-485 (SW1[1:2] = ON, ON)

SW2

Data port serial protocol

RS-485 (SW2[1:2] = ON, ON)

Diagnostics (software)

Modbus

Frame Format

RTU

Node

Baud Rate

115,200 Baud

Supported Function Codes

Function Code 3: Read Holding Registers Function Code 6: Write Single Holding Register (other codes are not available)

3.1 Configuration Settings and Initial User Setup

The 923-EDL cards are configured at the factory and the user does not need perform any additional card configuration settings to start operating the card and obtain diagnostics data.

3.1.1 Configuration Settings

Table 3-1: Factory Default Card Configuration Settings (as-built)

User defined parameters via the diagnostics port:

 Log interval (1 – 120 minutes)  Node ID (1 - 255)

Focal Technologies Corporation Page 3-2

A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 10

Model 923 Data Logger – User Manual

3.1.2 Initial User Setup

The only initial user setup requirement to start logging sensor data is to power up the 923-EDL card with +24 VDC (nominal). In order to access real-time sensor data the user can connect to the card via the RS-485 port using the sample FocalTM GUI as shown in the figure below or a 3rd party Modbus RTU software configured as a master.

Figure 3-2: Model 923-EDL Typical Setup Connection Using a PC and Focal GUI

3.2 Data Logging

The 923-EDL uses a proprietary logging algorithm that enables the card to compute the maximum, minimum and average measurement of all the sensor parameters within the specified log interval. This allows the user to select longer log intervals without losing sight of critical events within the specified log interval. The data logging interval can be set between 1 to 120 minutes and it can be changed by the user by using Focal’s GUI software through the data port J5.

The data obtained from the sensors is stored in the card’s on-board 32 MB flash memory. This memory size allows up to 14 years’ worth data to be stored when the log interval is set to 60 minutes.

3.3 Real Time Clock (RTC)

The 923-EDL has an on-board a real time clock (RTC) with an accuracy of ±5 ppm. An on-board, 3.3V rechargeable lithium-ion battery (B1) maintains the correct time even when the card is not powered for a period of up to four months. This real time clock is used as the time stamp when logging the sensor data into on-board flash memory. The time stamp will be reset to factory default if the battery has been drained – any data logged to the flash memory with a dead battery will be accurate, but the time stamp will start at 01/01/2000 00:00:00 (dd/mm/yyyy hh:mm:ss).

The on-board battery is recharged while the board is powered on. Note that the battery is intended solely to keep the RTC running, not to operate the entire data logger. Normally the RTC is operation even when there is no power applied to the card.

Note: The RTC is normally synchronized with a PC’s clock. The factory clock used to synchronize the RTC has

a time zone of UTC-04:00 (Atlantic Time Canada) and when connecting to the card using the sample GUI, the user will be prompted with the option to re-sync the RTC with the local PC or keep the factory default values. It is recommended to re-synchronize the RTC at the time of final system installation.

Focal Technologies Corporation Page 3-3

A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 11

Model 923 Data Logger – User Manual

Refer to section 7.0 of this document for details on how to convert Modbus sensor raw data into analog values for all the on-board sensors.

Do not expose the sensor to solvents or other corrosive liquids.

3.4 On-Board Sensors

The specifications for the on-board sensors of the Model 923-EDL card are given in section 2.0 of this document. The 923-EDL obtains a new sample from the on-board sensors every 5 ms. Note that the accuracy of the

temperature and humidity is for the sensors themselves and corresponds to the immediate vicinity of the sensors, which may deviate from the ambient air conditions inside the rotary product.

The card starts logging data at a user-defined log interval (1 to 120 minutes) as soon as it gets powered. After power-up the card calculates the maximum, minimum and average values read from all the sensors during the specified log interval and then saves this data to the on-board flash memory with a time stamp from the on-board real-time clock (RTC).

The real-time sensor data and the sensor data saved in flash can be accessed (downloaded) from the diagnostics port (J5) using the sample GUI (P/N: 923-0403-00) or using custom software configured as Modbus RTU master. The real-time raw data (non-formatted) of the on-board sensors is stored in Modbus registers.

3.4.1 Temperature and Humidity Sensor

The card uses a capacitive type humidity sensor with integrated temperature sensor. A protective cap is placed over the sensor.

3.4.2 3-Axis Accelerometer Sensor (Shock and Vibration)

The 3-axis accelerometer provides measurements up to ±200 g. This sensor measures both dynamic acceleration resulting from motion or shock and static acceleration, such as gravity. Shock and vibration data obtained from this sensor are saved in the on-board flash memory and also into Modbus registers. The X, Y and Z direction raw values are stored as 16-bit values. The shock events are logged into the flash memory as 32 data points per axis (10 data points before the event and 22 data points after the event).

3.4.3 Ambient Light Sensor

The light sensor used is capable of operating in the infrared and visible light spectrum. Illuminance (ambient light level) in lux is derived using an empirical formula to approximate the human-eye response.

The illuminance measured is stored as a 16-bit raw value in Modbus registers for real-time diagnostics and it is stored as formatted data (lux) in the on-board flash.

Refer to the Modbus register map section of this document for details on the formulas to obtain the lux values.

3.4.4 Rotation Sensor (Turns Counter and Speed)

The on-board rotation sensor is used to measure the direction (CW and CCW), speed (rpm) and total revolutions. This sensor requires custom hardware and is currently intended to be used with Focal rotary products. Contact the factory for more details.

Focal Technologies Corporation Page 3-4

A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 12

Model 923 Data Logger – User Manual

Applying higher voltages to the analog channels could damage the analog input circuits.

3.5 Interfaces

3.5.1 Thermocouple Inputs

The 923-EDL allows two (2) K-type thermocouples to be connected to 3 pin connectors J6 and J15. The card performs cold-junction compensation and the data output of each thermocouple is saved as an IEEE-754 32-bit floating point value in Modbus registers and also saved in the on-board flash memory.

3.5.2 Analog Inputs

The 923-EDL provides access to two (2) single-ended analog inputs via the 12-pin connector J4. The default input voltage range is dependent on a factory configurable resistor divider for each channel. The default configuration yields a maximum input on channel 1 of 14.76V. The maximum input on channel 2 is 4.95V.

The resolution of the ADC is 10-bit and the data is sampled at 200 Hz. Each ADC channel is calibrated at the factory using a scale factor (saved as an IEEE-754 32-bit floating point). The data output of each ADC and the scaler is stored in Modbus registers and in the on-board flash memory.

Focal Technologies Corporation Page 3-5

A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 13

Model 923 Data Logger – User Manual

4.0 Hardware

The Model 923-EDL card has a 923-0203-00 PCB assembly (PCBA). The PCBA has an external diameter of

3.37” [8.55 cm] (nom) and an internal diameter of 1.43” [3.63 cm] (nom). The card assembly is typically installed on FocalTM rotary products such as electrical slip rings (ESRs) and FPSOs.

This PCBA is designed for interfacing with a 9-pin Micro-D connector, which is used to provide power to the card and access real-time and stored diagnostics information.

Top and side views of the Model 923-EDL PCBA are shown in the figure below. For more details, refer to configuration drawing 923-2004-00.

Figure 4-1: Model 923-EDL PCBA

4.1 General Board Handling

The PCBA does not require forced air convective cooling. Generally heat from the card is conducted through the mounting hardware.

Care must always be taken during the handling of PCBAs to ensure product integrity. The following guidelines should be adhered to in working with PCBAs:

 Always handle boards by the edges and do not touch any connectors or gold tabs.  Handle boards at an ESD safe workstation with a clean surface.  Never stack PCB assemblies on top of one another.  Do not flex boards during handling or when mounted. The mounting surface needs to be flat and even

such that the board is not flexed when bolted down.

 Do not cause unnecessary shock and vibration, such as dropping or rough handling of the boards.  Do not expose light, temperature and humidity sensors to solvents or other corrosive liquids.

Focal Technologies Corporation Page 4-1 A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 14

Model 923 Data Logger – User Manual

Ref

Description

Manufacturer

Part Number

Mating Manufacturer

Part Number

9-Pin Micro-D

Molex

0836119006

ITT Cannon, MDM-9SSB, Micro-D,9-Pin, female

12-Pin Rcpt. 0.100”

Samtec

CES-106-01-S-D

TSW-106-07-T-D

Figure 5-1: Micro-D (9-pin) Power & Data

Connector (J5)

Table 5-2: Micro-D (9-pin) Connector (J5) Pin out

Function

RS-485+

RS-485-

ISO GND (for RS-485)

RESERVED

POWER

GND 8 RESERVED

RESERVED

Figure 5-2: Thermocouple Input Connectors (J6, J15)

Table 5-3: Thermocouple Input

(3-pin) Connector (J6, J15)

Pinout

Function

Thermocouple T+

Thermocouple T-

Ground

Note: For K-type thermocouples T+ is the yellow wire T- is the red wire

5.0 Electrical Connectors and Pin Descriptions

The 923-EDL card has three (3) connectors for customer access and a few others for factory programming and testing. A 9-pin Micro-D connector (J5) on the top side of the card provides access to the diagnostics data and is also used to power-up the board. Two three pin connectors (J6, J15) provide access to two thermocouple inputs, and a 12-pin receptacle (J4) provides access to two analog inputs.

Table 5-1: Connector/Mating Connector Part Numbers

5.1 9-pin Micro-D Power and Data Connector (J5)

Pin locations and functions are shown below for the 9-pin Micro-D connector.

5.2 Thermocouple Input Connectors (J6, J15)

The connectors used for thermocouple connections are shown below. The 3 holes have 0.100” spacing and the pinout described below. Thermocouple input 1 is connected to J6 and Thermocouple input 2 is connected to J15.

Focal Technologies Corporation Page 5-1 A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 15

Model 923 Data Logger – User Manual

Figure 5-3: 12-pin Analog Input Connector (J4)

Table 5-4: Analog Input (12-pin) Connector (J4)

Pin out

Function

OPEN (DEFAULT) OPTIONAL: +12VOUT OR +5VOUT (WITH HW MODS)

ANALOG INPUT CH1

GND

OPEN OPTIONAL: +12VOUT OR +5VOUT (WITH HW MODS) (DEFAULT +5V)

ANALOG INPUT CH2

GND 7 GND

RESERVED

OPEN (DEFAULT) OPTIONAL: +12VOUT OR +5VOUT (WITH HW MODS)

GND

RESERVED

OPEN (DEFAULT) OPTIONAL: +12VOUT OR +5VOUT (WITH HW MODS)

5.3 12-Pin Analog Input Connector (J4)

Focal Technologies Corporation Page 5-2 A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 16

Model 923 Data Logger – User Manual

Name

Length

(bits)

Function

Default Settings

(923-EDL as-built)

Start

At least 3.5 character times of silence (mark condition)

28 bits min.

Address

Station (node) address

Node 1

Function

Indicates the function code

Function Code 3: Read Holding Registers Function Code 6: Write Single Holding Register (other codes are not available)

Data

n * 8

Data + length will be filled depending on the message type

All Modbus registers are 16-bit values

CRC

Cyclic Redundancy Check

CRC-16-ANSI (a.k.a. CRC-16-IBM)

End

At least 3.5 character times of silence between frames

28 bits min.

6.0 Functionality

The main function of the Model 923-EDL card is to collect data from several on-board sensors and external interfaces and store it in the on-board non-volatile flash memory. The data collected can then be used for further analysis and evaluation of the environment in which the card is installed. The data stored in flash memory is saved as analog values and further processing is not required to convert raw sensor data into analog values, as this task is performed by the on-board microcontroller.

The Model 923 also supports in-field programming via the J5 port, which can be used for future firmware upgrades.

6.1 Serial Diagnostic Interface

Remotely accessible, real-time diagnostic data and status information is available from the 923-EDL via the port J5. This information can be used to determine current health and to analyze long-term trending of critical parameters of the system being monitored (e.g. to estimate the remaining life of a Focal rotary product).

Diagnostic and status information is retrieved from the following:

1. Temperature, humidity, accelerometer, ambient light and rotation sensors (details of these sensors are provided in section 3.4).

2. A bank of analog to digital converters (ADCs), which monitor board voltage rails.

3. Board information which includes serial number (S/N), data code, assembly number, firmware version, cause of reset and I2C error count.

4. On-board Flash memory information such as memory usage and current write pointer location.

The serial RS-485 interface (connector J5) of the 923-EDL operates in Modbus RTU mode.

6.1.1 Modbus RTU

The user can communicate with the 923-EDL using the Modbus RTU protocol over the serial RS-485 interface (J5). The default (as-built) settings are shown in the table below.

Table 6-1: Modbus RTU Frame Format and 923-EDL Defaults

Note: The default node address can be changed using the sample GUI.

Focal Technologies Corporation Page 6-1

A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 17

Model 923 Data Logger – User Manual

6.2 Diagnostics Software

6.2.1 Overview

Focal-Moog has created a sample .NET graphical user interface (GUI) to work with the 923-EDL in Modbus RTU mode. The 923-GUI (P/N: 923-0403-00) uses a serial connection to retrieve data from the 923-EDL using the Modbus RTU protocol. The GUI presents all data readings on a single window, as shown in the figure below. Live graphs of temperature, humidity, ambient light, rotational speed, etc., are provided as well as live readings from all sensors. Additional board identification information, such as card serial number, date code, etc., is also included.

Note: The GUI screenshots shown in this document might be updated from time-to-time to reflect new features or information added to the software. Contact the factory to obtain the latest version of the GUI.

Focal Technologies Corporation Page 6-2

A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Figure 6-1: 923-GUI

Page 18

Model 923 Data Logger – User Manual

6.2.2 Installation

System Requirements

 PC with Intel Pentium or AMD processor  256 MB of RAM  20 MB of available hard disk space for the application and documentation.  Supported Operating Systems: Windows 7 (64-bit)  .NET Framework (minimum version 4.0)  CD-ROM or DVD drive or USB port (to download the GUI)  PC with an available RS-485 serial COM port. Note: A USB-to-RS-485 converter might be used.

Installation Procedure

1. Copy the contents of the GUI folder to a local folder in your PC.

2. For example: C:\Focal\Model923\GUI\Release

3. Open the “Release” folder.

4. Double click on the executable *.exe file to run the Model 923 Diagnostic Software.

6.2.3 Application Usage

In order to establish a successful diagnostics connection with the 923-EDL, the card must be powered on (typically with +24V at connector J5) and the physical data communication link must be valid (also via the J5 connector). The connection between the PC and the card’s J5 port is via an RS-485 serial link. If the PC does not have an RS-485 port, then an external converter can be used (e.g. a USB-to-RS-485 converter). The list of

available serial ports and their descriptions can be found by opening the PC’s device manager (e.g. WIN+R (run)

 devmgmt.msc).

6.2.3.1 Connection Manager

The communication parameters for each card must be configured using the Connection Manager. To remove a

card configuration from the list, click the “X” button on the right of the card name. The Pen symbol can be clicked

to edit the existing card configuration.

Figure 6-2: Connection Manager

Focal Technologies Corporation Page 6-3 A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 19

Model 923 Data Logger – User Manual

6.2.3.2 Add a New Data Logger Configuration

To add a new card configuration to the list:

1. Click the button at the far left of the Connection Manager.

2. Enter a Description, Serial Port, Modbus Node and Refresh Interval for the new card, as depicted in the figure below.

3. Click “Save Configuration”.

Figure 6-3: Add a New Data Logger Configuration

Notes:

1. It is recommended to set the “refresh interval” to >= 1000 ms.

2. The default node is 1.

6.2.3.3 Connect and Disconnect Diagnostic Communications

Click to begin retrieving data from the card. Click to disconnect from the card.

Note:

If on start up a configuration tab is already open, the configuration shown corresponds to the last configuration used. This configuration may not apply for the current system. This could result in connection failures to the 923-EDL. It is recommended that on start-up, any existing and unknown configuration tabs are closed and new configurations are added or ensure the same configuration is always used.

Focal Technologies Corporation Page 6-4

A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 20

Model 923 Data Logger – User Manual

Select location to save the file

Begin download of internal flash

6.2.4 Special Features

6.2.4.1 Log Download

The GUI gives the user the ability to offload all the data on the 923-EDL into a .csv file. The time taken for the data offload is dependent on the amount of flash memory used on the 923-EDL. An estimated time for offload is given for user convenience. A valid serial connection with the 923-EDL is required for this feature. Controls for this feature can be seen in the image below.

Figure 6-4: 923-GUI – Reading the Data from Flash (Internal Log)

Focal Technologies Corporation Page 6-5 A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 21

Model 923 Data Logger – User Manual

28/07/2015 - 11:48:39

-----------------------------------------------------------------------------

Focal Technologies Model 923

-----------------------------------------------------------------------------

Cause of Last Reset : Power-up

Serial Number : 10052055

Date Code : 2015-07-14

Assembly Number : 923-0203-00

FW Version : A0

DataLog Interval : 1 min

Baud Rate : 115200

Number of Magnets in the Rotary Encoder : 36

MODBUS Node ID : 1

Accelerometer Range : +\-200(g)

+3.3V Supply : 3.236 V

+12V Supply : 14.572 V

Memory Usage : 4.521%

Output Format : MODBUS RTU

Total Rotations : 4.417

Total CW Rotations : 2.444

Total CCW Rotations : 1.972

Total Bytes : 1517312

Read Time : 321.4(sec)

6.2.4.1.1 Data Log File – Flash Memory Contents Example

File Name: 923DataLog_7_28_2015_11_48_27.csv Static Data:

Focal Technologies Corporation Page 6-6 A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 22

Model 923 Data Logger – User Manual

Date

Time … Card Status

DD/MM/YYYY

hh:mm:ss

…

DD/MM/YYYY

hh:mm:ss

…

: : :

Header Data Header Data Header Data

Date 23/07/2015 ADC0 Max 1.6395 Acclerometer X Max(g) 1.078

Time 09:05:07 ADC0 Min 1.6335 Acclerometer X Min(g) -0.196

3.3v Rail Max(V) 3.279 ADC0 Avg 1.6365 Acclerometer X Avg(g) 0.637

3.3v Rail Min(V) 3.261 ADC1 Max 1.6395 Acclerometer Y Max(g) 0.392

3.3v Rail Avg(V) 3.272 ADC1 Min 1.6335 Acclerometer Y Min(g) -1.078

5.0v Rail Max(V) 4.868 ADC1 Avg 1.6365 Acclerometer Y Avg(g) 0.049

5.0v Rail Min(V) 4.85 ADC2 Max 1.6395 Acclerometer Z Max(g) 2.254

5.0v Rail Avg(V) 4.861 ADC2 Min 1.6335 Acclerometer Z Min(g) 0.588

12.0v Rail Max(V) 11.894 ADC2 Avg 1.6365 Acclerometer Z Avg(g) 1.715

12.0v Rail Min(V) 11.877 ADC3 Max 1.6395 Am bient Light Max(lux) 9.124

12.0v Rail Avg(V) 11.881 ADC3 Min 1.6335 Ambient Light Min(lux) 9.091

Thermoc ouple 1 Max(degC) 28 ADC3 Avg 1.6365 Ambient Light Avg(lux) 9.124

Thermoc ouple 1 Min(degC) 27.75 Speed Max(rpm) 10 Card Status NORMAL

Thermoc ouple 1 Avg(DegC) 27.922 Speed Min(rpm) 0

Thermoc ouple 2 Max(degC) 30.031 Speed Avg(rpm) 1

Thermoc ouple 2 Min(degC) 29.812 T otal Rotations 4.194

Thermoc ouple 2 Avg(DegC) 30.505

Temperature Max(degC) 27.19

Temperature Min(degC) 27.126

Temperature Avg(DegC) 27.168

Humidity Max(%) 46.031

Humidity Min(%) 45.596

Humidity Avg(%) 45.685

Sensor Data:

Note: The data shown above is the transposed version of the actual *.csv log file. The .csv file is formatted as

follows:

Focal Technologies Corporation Page 6-7 A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 23

Model 923 Data Logger – User Manual

Select read back file

Load file

6.2.4.2 Local Logging to PC

Local logging allows the user to save the data displayed by the GUI software to a .csv file in the local PC. Local logging is stopped when the GUI is closed.

6.2.4.3 Log Read-back

The GUI also has the ability to load a saved .csv file into the presentation fields. The fields populated with data include temperature, humidity, light, speed, acceleration and voltage. This will allow the user to analyze past data for trends by viewing the loaded data in the graph windows. Additionally, the GUI will display the maximum and minimum sensor values which were recorded in the loaded data, allowing the user to see if any spikes or dips occurred while logging. This is not a real time play-back feature. All data will be loaded in one instance for viewing. A valid serial connection with the 923-EDL is not required to use this feature. Controls for this feature can be seen in the image below.

Figure 6-5: 923-GUI – File Read-back Function (Load Log)

Focal Technologies Corporation Page 6-8 A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 24

Model 923 Data Logger – User Manual

Alarm settings are saved in the local computer and are only applicable to the GUI – not the 923-EDL card. Any changes to the alarm values will only be reflected in the GUI, the 923 card will continue to operate normally regardless of the software alarm settings.

6.2.4.4 Alarm Configurations

The GUI includes alarm levels for measured values. These alarm levels are configurable by the user in the alarms window shown in the figure below. Unsaved values are highlighted and current alarm levels can be restored at any point. The GUI provides the user the ability to change alarms, save alarm configurations as a .csv file, and upload previously saved alarm configuration files.

Figure 6-6: 923-GUI – Alarm Configuration

The default alarm levels used on GUI start-up are saved in a configuration file stored in the same directory as the run file. The file containing the alarm levels can be edited in a text editor or Excel so that the same alarm levels are loaded on each startup. The configuration file must be saved in .csv format.

Focal Technologies Corporation Page 6-9

A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 25

Model 923 Data Logger – User Manual

6.2.4.5 Time Synchronization

The 923-GUI allows the user to synchronize the 923-EDL real time clock (RTC) with the user’s computer time. If time synchronization is enabled and a time discrepancy of greater than or equal to one (1) minute is measured, a prompt will be raised to ask the user if the 923-EDL RTC should be synchronized with the local computer (see

figure below). By pressing “synchronize”, the 923-EDL RTC will be synchronized with the PC clock and by pressing “Cancel” the time synchronization feature will be disabled. This window will timeout in 10 seconds and

assume time synchronization is not desired.

Figure 6-7: 923-GUI – Time Synchronization of 923-EDL RTC’s with PC

Focal Technologies Corporation Page 6-10 A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 26

Model 923 Data Logger – User Manual

6.2.4.6 Adjustable Analog Input Display

The 923-GUI allows the user to setup a customizable view for each of the measured analog inputs. This customizable view will allow the user to display specific units and alarms for each channel as well as applying an equation to the measured voltage to convert or scale the reading to different units. For example, if a user had a temperature sensor connected to analog input 1 where the measured temperature was calculated using the equation below, the equation can be entered into the GUI and the temperature will be displayed in the “Adjusted” tab of the Analog Inputs expander.

𝑇 =(𝑉𝑜 ∗ 3

The equation and units for each channel are edited in the ADC Controls tab of the Diagnostic Card expander. In this tab the user can also set alarm and warning levels for the adjusted value. The alarm levels, units and equation are saved for each channel in an .xml file in the GUI release folder named ADCEquations.xml. The values are loaded from the .xml file each time the GUI is opened. This feature is exclusively a software feature meaning the data logged to the 923-EDL will still be saved as raw analog counts. Examples of the adjusted ADC values can be seen in the images below.

)

+ 32

Figure 6-8: 923-GUI – ADC Controls

Figure 6-9: 923-GUI – Adjusted Analog Input

Focal Technologies Corporation Page 6-11 A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 27

Model 923 Data Logger – User Manual

Board Diagnostics Information

Bit

R/W

Description

Comments

40001

15:0 R Serial Output Mode

0: Reserved 1: Reserved 2: Reserved 3: Modbus RTU Mode

40002

15:8 R Month

Date saved as ASCII

7:0 R Day

40003

15:0 R Year

40004

15:8 R Minutes

Time saved as ASCII

7:0 R Seconds

40005

15:8 R Reserved

7:0 R Hour

40006

15:0 R Log Interval

In minutes (1-120)

40007

15:0

3.3 V ADC

Voltage (V) = ModbusReg[40007] * 0.0058

40008

15:0

5 V ADC

Voltage (V) = ModbusReg[40008] * 0.0058

40009

15:0

12 V ADC

Voltage (V) = ModbusReg[40009] * 0.017578

40010

15:0

Reserved

40011

15:0

Temperature Sensor

See “On-board Sensor Registers” section.

40012

15:0

Humidity Sensor

40013

15:0

Light Sensor [1]

40014

15:0

Light Sensor [2]

40015

15:0

RPM [1]

40016

15:0

RPM [2]

40017

15:0

Total Rotations [1]

40018

15:0

Total Rotations [2]

40019

15:0

CW Rotations [1]

40020

15:0

CW Rotations [2]

40021

15:0

CCW Rotations [1]

40022

15:0

CCW Rotations [2]

40023

15:0

Direction

40024

15:0

Acceleration X

40025

15:0

Acceleration Y

40026

15:0

Acceleration Z

40027

15:0

Micro Firmware Revision

40028

15:0

Cause of Last Micro Reset

0: Power-Up 2: Watchdog 3: Software Power-up 4: User (NRST pin) 5: Brownout

40029

15:0 R Number of Magnets

40030

15:0 R Reserved

40031

15:0 R Memory Pointer [1]

Current Location in the flash memory. This value does not include an offset at the beginning of the flash which stores factory use code.

40032

15:0 R Memory Pointer [2]

40033

15:0 R Reserved

40034

15:0 R Reserved

40035

15:0 R I2C Error Counter

Reports the number of I2C errors occurred

40036

15:0 R Reserved

40037

15:0 R Reserved

40038

15:8 R Thermocouple 1 Byte 1

Saved as IEEE 4 byte float value. (See “Sensor Data Conversion” section for details.)

7:0 Thermocouple 1 Byte 0

40039

15:8 R Thermocouple 1 Byte 3

7:0 Thermocouple 1 Byte 2

40040

15:8 R Thermocouple 2 Byte 1

7:0 Thermocouple 2 Byte 0

40041

15:8 R Thermocouple 2 Byte 3

7:0 Thermocouple 2 Byte 2

7.0 Register Maps

7.1 Modbus RTU Register Map

Focal Technologies Corporation Page 7-1 A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 28

Model 923 Data Logger – User Manual

Board Diagnostics Information

Bit

R/W

Description

Comments

40042

15:0 R Reserved

40043

15:0 R Analog Input Ch 1

See “On-board Sensor Registers” section.

40044

15:8 R Analog Input Ch 1 Scalar Byte 1

7:0 R Analog Input Ch 1 Scalar Byte 0

40045

15:0 R Analog Input Ch 1 Scalar Byte 3

7:0 R Analog Input Ch 1 Scalar Byte 2

40046

15:0 R Analog Input Ch 2

40047

15:8 R Analog Input Ch 2 Scalar Byte 1

7:0 R Analog Input Ch 2 Scalar Byte 0

40048

15:0 R Analog Input Ch 2 Scalar Byte 3

7:0 R Analog Input Ch 2 Scalar Byte 2

40049

15:0 R Reserved

40050

15:8 R Reserved

7:0 R Reserved

40051

15:0 R Reserved

7:0 R Reserved

40052

15:0 R Reserved

40053

15:8 R Reserved

7:0 R Reserved

40054

15:0 R Reserved

7:0 R Reserved

40055-

40229

15:0 R Reserved

Board Information Registers

Bit

R/W

Description

Comments

40230

15:0

Serial Number [1]

Serial Number

40231

15:0

Serial Number [2]

40232

15:0

Serial Number [3]

40233

15:0

Serial Number [4]

40234

15:0

Serial Number [5]

40235

15:0

Serial Number [6]

40236

15:0

Serial Number [7]

40237

15:0

Serial Number [8]

40238

15:0

Date Code [1]

Date Code

40239

15:0

Date Code [2]

40240

15:0

Date Code [3]

40241

15:0

Date Code [4]

40242

15:0

Date Code [5]

40243

15:0

Date Code [6]

40244

15:0

Date Code [7]

40245

15:0

Date Code [8]

40246

15:0

Assembly Number [1]

Assembly Number

40247

15:0

Assembly Number [2]

40248

15:0

Assembly Number [3]

40249

15:0

Assembly Number [4]

40250

15:0

Assembly Number [5]

40251

15:0

Assembly Number [6]

40252

15:0

Assembly Number [7]

40253

15:0

Assembly Number [8]

40254

15:0

PCB Number [1]

PCB Number

40255

15:0

PCB Number [2]

40256

15:0

PCB Number [3]

40257

15:0

PCB Number [4]

40258

15:0

PCB Number [5]

40259

15:0

PCB Number [6]

40260

15:0

PCB Number [7]

40261

15:0

PCB Number [8]

40262-

40517

15:0 R Reserved

40518

15:0 R Log File Size Lower

32 bit value saved as ASCII

40519

15:0 R Log File Size Upper

40520-

40799

15:0 R Reserved

Focal Technologies Corporation Page 7-2

A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 29

Model 923 Data Logger – User Manual

Shock Event Registers

Bit

R/W

Description

Comments

40800

15:8

Stored Max Shock Value Byte 1

Max shock from most recent shock event. Saved as IEEE 4 byte float value. (See “Sensor Data Conversion” section for details.)

7:0 R Stored Max Shock Value Byte 0

40801

15:8

Stored Max Shock Value Byte 3

7:0 R Stored Max Shock Value Byte 2

40802

15:8

Current Max Shock Value Byte 1

7:0 R Current Max Shock Value Byte 0

40803

15:8

Current Max Shock Value Byte 3

7:0 Current Max Shock Value Byte 2

40804-

40809

15:0 R Reserved

40810-

40841

15:0 R Shock Event X Data 0-31

See “On-board Sensor Registers” section.

40842-

40873

15:0 R Shock Event Y Data 0-31

40874-

40909

15:0 R Shock Event Z Data 0-31

40910-

41050

15:0 R Reserved

Focal Technologies Corporation Page 7-3

A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 30

Model 923 Data Logger – User Manual

On-board Sensor Information

Bit

R/W

Description

Temperature Sensor

40011

15:0 R Temperature Sensor

Equation Temp = (ModbusReg[40011] * 0.0026812) – 46.5

Example: Temp = 27.94 degC

Temperature = (27764 * 0.0026812) – 46.5

= 27.94

Humidity Sensor

40012

15:0 R Humidity Sensor

Equation Humidity = (ModbusReg[40012] * 0.0019073) – 6

Example: Humidity = 41.90%

Humidity = (25112 * 0.0019073) – 6

= 41.90

Light Sensor

40013

15:0 R Light Sensor [1] (Ch1)

40014

15:0 R Light Sensor [2] (Ch2)

Equations

Ratio = Ch2/Ch1

If 0 ≤ Ratio ≤ 0.52: Luminance = (0.0315*Ch1)-(0.0539*Ch1*((Ch2/Ch1)^1.4))

If 0.52 ≤ Ratio ≤ 0.65: Luminance = (0.0229*Ch1)-(0.0291*Ch2)

If 0.65 ≤ Ratio ≤ 0.80 Luminance = (0.0157*Ch1)-(0.0180* Ch2)

If 0.80 ≤ Ratio ≤ 1.30 Luminance = (0.00338*Ch1)-(0.00260* Ch2)

If Ratio ≥ 1.30 Luminance = 0

Example: Lum = 46.35 lux

Ch1 = 1748 Ch2 = 319

Ratio = 0.182494283

Luminance = (0.0315 * 1748)–(0.0539 * 1748 * (Ratio^1.4))

= 46.35

Rotation Sensor (Turns Counter and Speed)

40015

15:0 R RPM[1] (bits 15:0)

Equations:

Formatted Data = Raw Data Big endian.

Example:

The Modbus 32-bit value is already formatted and

no further conversion is required.

40016

15:0 R RPM [2] (bits 31:16)

40017

15:0 R Total Rotations [1]

40018

15:0 R Total Rotations [2]

40019

15:0 R Clockwise Rotations [1]

40020

15:0 R Clockwise Rotations [2]

40021

15:0 R Counter Clockwise Rotations [1]

40022

15:0 R Counter Clockwise Rotations [2]

40023

15:8

Reserved

2 R Counter Clockwise Rotation

1=CCR detected. 0 = CCR not detected

1 R Clockwise Rotation

1=CR detected. 0 = CR not detected

No Rotation

1=No Rotation detected. 0 = Rotation detected

3-Axis Accelerometer (Shock and Vibration Sensor)

40024

15:0

Acceleration X

40025

15:0

Acceleration Y

40026

15:0

Acceleration Z

40810-

40909

15:0 R Shock Event X,Y,Z Data 0-31

7.1.1 On-board Sensor Registers

Focal Technologies Corporation Page 7-4 A Moog Inc. Company Document No: 923-0603-01, Rev. 2

Page 31

Model 923 Data Logger – User Manual

On-board Sensor Information

Bit

R/W

Description

Equation

Raw = ModbusReg[xxxxx] If Raw > 32768 Accel = (65536 – Raw) * 0.049 * -1 Else

Accel = Raw * 0.049

Example: Acceleration = 0.748 g

Raw = 16 Accel = 16 * 0.049

= 0.748

On-board Sensor Information

Bit

R/W

Description

ADC External Inputs CH1 – CH4

40043-

40054

15:0

Analog Input and Scalar Values for Channels 1-4

Voltage (V) = AnalogInputChX * AnalogInputScalarChx Where ChX = Ch1,Ch2

AnalogInputScalarChx = BytesToFloat( AnalogInputChX_ScalarByte3, AnalogInputChX_ScalarByte2, AnalogInputChX_ScalarByte1, AnalogInputChX_ScalarByte0)

See “Sensor Data Conversion” section for

details.

Example: Voltage = 1.65V

Scalar = BytesToFloat(0x3B, 0x40, 0x30, 0x06) = 0.00293255

V = 562 * Scalar = 1.65

BytesToFloat(byte3, byte2, byte1, byte0):

temp = (byte3<<24)|(byte2<<16)|(byte1<<8)|(byte0) mantissa = (1 + (temp & 0x007FFFFF) * (2^-23)) exp = ((temp & 0x7F800000) >> 23) – 127 isPos = (((temp & 0x80000000) >> 31) == 0)

If isPos: Float = (2^exp) * mantissa Else: Float = (-1 * ((2^exp) * mantissa))

7.1.2 Sensor Data Conversion

7.1.2.1 IEEE 4 Byte Float Conversion (Bytes to Float)

Focal Technologies Corporation Page 7-5

A Moog Inc. Company Document No: 923-0603-01, Rev. 2