FMI GWN10A, GWN10TA, GWP10A, GWP10TA, VSHN10M Safety Information And Installation Manual

VENT-FREE GAS HEATER

PFS

®

US

SAFETY INFORMATION AND INSTALLATION MANUAL

MODELS

GWN10A, GWP10A,
GWN10TA, GWP10TA,
VSHN10M, VSHP10M,

VSHN10T, VSHP10T

WARNING: If the information in this manual is not

followed exactly, a re or explosion may result causing
property damage, personal injury or loss of life.

— Do not store or use gasoline or other ammable

vapors and liquids in the vicinity of this or any other
appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any
phone in your building.

• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re
department.

— Installation and service must be performed by a quali-

ed installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

For more information, visit www.fmiproducts.com

Safety .................................................................. 2

TABLE OF CONTENTS

Local Codes......................................................... 4

Product Identication ........................................... 4

Unpacking............................................................ 4

Product Features ................................................. 4

Air For Combustion and Ventilation ..................... 5

Installation ........................................................... 7

Operation ........................................................... 13

Inspecting Heater .............................................. 15

SAFETY

Cleaning and Maintenance ................................ 16

Troubleshooting ................................................. 17

Specications .................................................... 21

Replacement Parts ............................................ 21

Service Hints ..................................................... 21

Technical Service............................................... 21

Parts .................................................................. 22

Warranty ..............................................Back Cover

WARNING: Improper

installation, adjustment,

alteration, service or main-

tenance can cause injury
or property damage. Refer

to this manual for correct

installation and operation­al procedures. For assis-

tance or additional infor-

mation consult a qualied
installer, service agency
or the gas supplier.

WARNING: This is an

unvented gas-red heat­er. It uses air (oxygen)

from the room in which

it is installed. Provisions
for adequate combustion

and ventilation air must

be provided. Refer to Air
for Combustion and Ven­tilation section on page 5

of this manual.

This appliance is only for
use with the type of gas
indicated on the rating
plate. This appliance is
not convertible for use
with other gases.

www.fmiproducts.com

This appliance may be in­stalled in an aftermarket,*

perma n ently locat e d,
manufactured (mobile)
home, where not prohib­ited by local codes.

* Aftermarket: Completion of sale, not for
purpose of resale, from the manufacturer

WARNING: This product con-

tains and/or generates chemicals

known to the State of California

to cause cancer or birth defects
or other reproductive harm.

IMPORTANT: Read this owner’s
manual carefully and completely
be for e t rying to assemble,
operate or service this heater.
Improper use of this heater can
cause serious injury or death
from burns, fire, explosion,
electrical shock and carbon
monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs

of carbon monoxide poisoning resemble the

u, with headaches, dizziness or nausea. If
you have these signs, the heater may not be
working properly. Get fresh air at once! Have
heater serviced. Some people are more af­fected by carbon monoxide than others. These
include pregnant women, people with heart or
lung disease or anemia, those under the inu­ence of alcohol and those at high altitudes.

125326-01A2

SAFETY

Continued

Natural and Propane/LP Gas: Natural and
propane/LP gases are odorless. An odor­making agent is added to these gases. The
odor helps you detect a gas leak. However, the
odor added to the gas can fade. Gas may be
present even though no odor exists.

Make certain you read and understand all
warnings. Keep this manual for reference. It
is your guide to safe and proper operation of
this heater.

WARNING: Any change to

this heater or its controls can

be dangerous.

WARNING: Do not use a

blower insert, heat exchanger
insert or other accessory not ap­proved for use with this heater.

Due to high temperatures, the
appliance should be located out
of trafc and away from furniture
and draperies.

Do not place clothing or other
ammable material on or near
the appliance. Never place any
objects on the heater.

Surface of heater becomes very
hot when running heater. Keep

children and adults away from

hot surface to avoid burns or
clothing ignition. Heater will

remain hot for a time after shut-

down. Allow surface to cool
before touching.

Carefully supervise young chil-

dren when they are in the room

with heater.

Make sure grill guard is in place
before running heater.

125326-01A 3

www.fmiproducts.com

Keep the appliance area clear
and free from combustible ma­terials, gasoline and other am­mable vapors and liquids.

1. This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases.

2. Do not place propane/LP supply tank(s)
inside any structure. Locate propane/LP
supply tank(s) outdoors.

3. Do not install 10,000 Btu units in a bathroom.

4. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not

use any phone in your building

• immediately call your gas supplier from

a neighbor’s phone. Follow the gas sup­plier’s instructions

• if you cannot reach your gas supplier,

call the re department

5. This heater needs fresh, outside air ven­tilation to run properly. This heater has an
Oxygen Depletion Sensing (ODS) safety
shutoff system. The ODS shuts down the
heater if not enough fresh air is available.
See Air for Combustion and Ventilation,
page 5.

6. Always run heater with control knob at the
locked positions or ON position. Never set
control knob between locked positions.
Poor combustion and higher levels of
carbon monoxide may result.

7. Keep all air openings in front and bot­tom of heater clear and free of debris.
This will insure enough air for proper
combustion.

8. If heater shuts off, do not relight until you
provide fresh, outside air. If heater keeps
shutting off, have it serviced.

9. Do not run heater

• where ammable liquids or vapors are
used or stored

• under dusty conditions

10. Before using furniture polish, wax, carpet
cleaner or similar products, turn heater off.
If heated, the vapors from these products
may create a white powder residue within
burner box or on adjacent walls or furni­ture.

11. Do not use heater if any part has been

Control Knob

Ignitor Button

Glass
Panel

Front
Panel

Heater
Cabinet

Grill
Guard

under water. Immediately call a qualied
service technician to inspect the room

heater and to replace any part of the

control system and any gas control which
has been under water.

12. Turn off and let cool before servicing. Only
a qualied service person should service
and repair heater.

13. Operating heater above elevations of
4,500 feet (1,371 m) could cause pilot
outage.

14. To prevent performance problems, do not
use propane/LP fuel tank of less than 100
lbs. (45 kg) capacity.

15. Provide adequate clearances around air

openings.

LOCAL CODES

Install and use heater with care. Follow all
local codes. In the absence of local codes,
use the latest edition of The National Fuel

Gas Code ANSI Z223/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

National Fire Protection Association, Inc.

State of Massachusetts: The installa­tion must be made by a licensed plumber
or gas fitter in the Commonwealth of
Massachusetts.

Sellers of unvented propane or natural
gas-red supplemental room heaters shall
provide to each purchaser a copy of 527
CMR 30 upon sale of the unit.

Vent-free gas products are prohibited for

bedroom and bathroom installation in the

Commonwealth of Massachusetts.

1430 Broadway

New York, NY 10018

Batterymarch Park
Quincy, MA 02269

SAFETY

Continued

PRODUCT

IDENTIFICATION

Figure 1 - Vent-Free Gas Heater

(actual heater may vary from illustration

PRODUCT FEATURES

SAFETY DEVICE

This heater has a pilot with an Oxygen Deple­tion Sensing (ODS) safety shutoff system. The
ODS/pilot is a required feature for vent-free
room heaters. The ODS/pilot shuts off the
heater if there is not enough fresh air.

PIEZO IGNITION SYSTEM

This heater has a piezo ignitor. This system re­quires no matches, batteries or other sources
to light heater.

UNPACkING

1. Remove heater from carton.

2. Remove all protective packaging applied
to heater for shipment.

3. Check heater for any shipping damage. If
heater is damaged call FMI PRODUCTS,

LLC at 1-866-328-4537 for replacement

parts before returning to dealer.

www.fmiproducts.com

125326-01A4

AIR FOR COMBUSTION AND VENTILATION

WARNING: This heater shall

not be installed in a room or space
unless the required volume of in­door combustion air is provided
by the method described in the

National Fuel Gas Code, ANSI
Z223.1/NFPA 54, the International
Fuel Gas Code, or applicable lo-

cal codes. Read the following in­structions to insure proper fresh
air for this and other fuel-burning
appliances in your home.

Today’s homes are built more energy efcient
than ever. New materials, increased insulation
and new construction methods help reduce
heat loss in homes. Home owners weather
strip and caulk around windows and doors to
keep the cold air out and the warm air in. Dur­ing heating months, home owners want their
homes as airtight as possible.

While it is good to make your home energy
efcient, your home needs to breathe. Fresh
air must enter your home. All fuel-burning ap­pliances need fresh air for proper combustion
and ventilation.

Exhaust fans, heaters, clothes dryers and fuel
burning appliances draw air from the house to
operate. You must provide adequate fresh air
for these appliances. This will insure proper
venting of vented fuel-burning appliances.

PROVIDING ADEQUATE
VENTILATION

The following are excerpts from National Fuel
Gas Code. ANSI Z223.1/NFPA 54, Air for
Combustion and Ventilation.

All spaces in homes fall into one of the three

following ventilation classications:

1. Unusually Tight Construction

2. Unconned Space

3. Conned Space

The information on pages 5 through 7 will
help you classify your space and provide
adequate ventilation.

Unusually Tight Construction

The air that leaks around doors and windows
may provide enough fresh air for combustion
and ventilation. However, in buildings of un­usually tight construction, you must provide
additional fresh air.

Unusually tight construction is dened as
construction where:

a. walls and ceilings exposed to the outside

atmosphere have a continuous water
vapor retarder with a rating of one perm

-11

(6x10

kg per pa-sec-m2) or less with

openings gasketed or sealed and

b. weather stripping has been added on

openable windows and doors and

c. caulking or sealants are applied to areas

such as joints around window and door
frames, between sole plates and oors,
between wall-ceiling joints, between wall
panels, at penetrations for plumbing,

electrical and gas lines and at other open-

ings.

If your home meets all of the three criteria above,
you must provide additional fresh air. See Ven-
tilation Air From Outdoors, page 7.

If your home does not meet all of the three
criteria above, proceed to Determining Fresh-
Air Flow For Heater Location.

Conned Space and Unconned Space

The National Fuel Gas Code ANSI Z223.1/
NFPA 54 denes a conned space as a space

whose volume is less than 50 cubic feet per
1,000 Btu per hour (4.8 m3 per kw) of the ag­gregate input rating of all appliances installed
in that space and an unconned space as a
space whose volume is not less than 50 cubic
feet per 1,000 Btu per hour (4.8 m3 per kw)
of the aggregate input rating of all appliances
installed in that space. Rooms communicating
directly with the space in which the appliances
are installed*, through openings not furnished
with doors, are considered a part of the un­conned space.

* Adjoining rooms are communicating only if
there are doorless passageways or ventilation
grills between them.

125326-01A 5

www.fmiproducts.com

AIR FOR COMBUSTION AND VENTILATION

Continued

DETERMINING FRESH-AIR FLOW
FOR HEATER LOCATION

Determining if You Have a Conned or
Unconned Space

Use this work sheet to determine if you have
a conned or unconned space.

Space: Includes the room in which you will install
heater plus any adjoining rooms with doorless
passageways or ventilation grills between the
rooms.

1. Determine the volume of the space (length
x width x height).

Length x Width x Height =__________cu. ft.

(volume of space)

Example: Space size 20 ft. (6.1m) (length) x

16 ft. (4.88m) (width) x 8 ft. (2.44 m) (ceiling
height) = 2,560 cu. ft. (72.49 m2)(volume of
space)

If additional ventilation to adjoining room

is supplied with grills or openings, add the
volume of these rooms to the total volume
of the space.

2. Multiply the space volume by 20 to determine
the maximum Btu/Hr the space can support.

________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

Example: 2,560 cu. ft. (72.49 m2) (volume of

space) x 20 = 51,200 (maximum Btu/Hr the
space can support)

3. Add the Btu/Hr of all fuel burning appliances
in the space.

Vent-free heater _________ Btu/Hr
Gas water heater* _________ Btu/Hr
Gas furnace _________ Btu/Hr
Vented gas heater _________ Btu/Hr
Gas heater logs _________ Btu/Hr
Other gas appliances* + _________ Btu/Hr
Total = _________Btu/Hr
* Do not include direct-vent gas appliances.

Direct-vent draws combustion air from the
outdoors and vents to the outdoors.

Example:

Gas water heater _________ Btu/Hr
Vent-free heater + _________Btu/Hr
Total = _________Btu/Hr

4. Compare the maximum Btu/Hr the space
can support with the actual amount of Btu/
Hr used.

_______ Btu/Hr (maximum can support)
_______ Btu/Hr (actual amount used)
Example: 51,200 Btu/ Hr (ma ximum the

space can support)

60,000 Btu/Hr (actual amount of

Btu/Hr used)

40,000
20,000

60,000

www.fmiproducts.com

The space in the example is a conned space
because the actual Btu/Hr used is more than the
maximum Btu/Hr the space can support. You
must provide additional fresh air. Your options
are as follows:

A. Rework worksheet, adding the space of an

adjoining room. If the extra space provides an
unconned space, remove door to adjoining
room or add ventilation grills between rooms.
See Ventilation Air From Inside Building.

B. Vent room directly to the outdoors. See

Ventilation Air From Outdoors, page 7.

C. Install a lower Btu/Hr heater, if lower Btu/Hr

size makes room unconned.

If the actual Btu/Hr used is less than the maxi­mum Btu/Hr the space can support, the space is
an unconned space. You will need no additional
fresh air ventilation.

WARNING: If the area in which

the heater may be operated does
not meet the required volume for
indoor combustion air, combus­tion and ventilation air shall be
provided by one of the methods
described in the National Fuel

Gas Code, ANSI Z223.1/NFPA 54,
the International Fuel Gas Code,

or applicable local codes.

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining
unconned space. When ventilating to an
adjoining unconned space, you must provide
two permanent openings: one within 12" (30.5
cm) of the ceiling and one within 12" (30.5 cm)
of the oor on the wall connecting the two
spaces (see options 1 and 2, Figure 2, page

7). You can also remove door into adjoining
room (see option 3, Figure 2, page 7). Follow

the National Fuel Gas Code, ANSI Z223.1/
NFPA 54, Air for Combustion and Ventilation

for required size of ventilation grills or ducts.

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills
or ducts. You must provide two permanent
openings: one within 12" (30.5 cm) of the ceil­ing and one within 12" (30.5 cm) of the oor.
Connect these items directly to the outdoors
or spaces open to the outdoors. These spaces
include attics and crawl spaces. Follow the Na-

tional Fuel Gas Code, ANSI Z223.1/NFPA 54,

Air for Combustion and Ventilation for required
size of ventilation grills or ducts.

125326-01A6

Or

Remove
Door into
Adjoining

Room,

Option 3

Ventilation Grills

Into Adjoining Room,

Option 2

12"

12"

Ventilation

Grills into
Adjoining

Room,

Option 1

Outlet
Air

Ventilated
Attic

Outlet
Air

Inlet
Air

Inlet Air

Ventilated

Crawl Space

To

Crawl

Space

To Attic

AIR FOR COMBUSTION AND VENTILATION

Figure 2 - Ventilation Air from Inside

Building

INSTALLATION

NOTICE: This heater is intended

for use as supplemental heat.
Use this heater along with your
primary heating system. Do not
install this heater as your pri­mary heat source. If you have a
central heating system, you may
run system’s circulating blower
while using heater. This will help
circulate the heat throughout the
house. In the event of a power
outage, you can use this heater
as your primary heat source.

WARNING: A qualied ser­vice person must install heater.
Follow all local codes.

CHECK GAS TYPE

Use only the correct gas type (natural
or propane/LP) for your unit. If your gas
supply is not correct, do not install heater.
Call dealer where you bought heater for
proper type heater.

Continued

IMPORTANT: Do not provide openings for inlet
or outlet air into attic if attic has a thermostat­controlled power vent. Heated air entering the
attic will activate the power vent.

Figure 3 - Ventilation Air from Outdoors

WARNING: This appliance is
equipped for either natural gas or
propane/LP gas but not both. Gas
type is indicated on the rating plate.
Field conversion is not permitted.

INSTALLATION ITEMS

Before installing heater, make sure you have
the items listed below.

• for propane/LP gas, external regulator
(supplied by installer)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• ground joint union

• sediment trap

• tee joint

• pipe wrench

• for natural gas, test gauge connection*

* An equipment shutoff valve with 1/8" NPT
tap is an acceptable alternative to test gauge
connection. The optional equipment shutoff
valve can be purchased from your dealer.

125326-01A 7

www.fmiproducts.com

INSTALLATION

36" (91.5 cm)

3" (7.7 cm)

FLOOR

CEILING

Minimum

6"

(15.3 cm)

Minimum
From
Sides Of
Heater

Right
Side

Left
Side

36"

(91.5 cm)

Minimum To

Top Surface Of

Carpeting, Tile Or

Other Combustible

Material

Continued

LOCATING HEATER

This heater is designed to be mounted on a wall.

WARNING: Maintain the

minimum clearances shown

in Figure 4. If you can, provide
greater clearances from oor,
ceiling and joining wall.

WARNING: Never install the

heater

• in a bedroom or bathroom

• in a recreational vehicle

• where curtains, furniture, cloth­ing or other ammable objects
are less than 36" (91.5 cm)
from the front, top or sides of

the heater

• as a replace insert

• in high trafc areas

• in windy or drafty areas

CAUTION: If you install the

heater in a home garage

• heater pilot and burner must be at
least 18" (45.7 cm) above oor

• locate heater where moving

vehicle will not hit it

CAUTION: This heater creates

warm air currents. These currents

move heat to wall surfaces next

to heater. Installing heater next
to vinyl or cloth wall coverings or
operating heater where impurities
(such as, but not limited to, to­bacco smoke, aromatic candles,
cleaning uids, oil or kerosene
lamps, etc.) in the air exist, may
discolor walls or cause odors.

IMPORTANT: Vent-free heaters add mois­ture to the air. Although this is benecial,
installing heater in rooms without enough
ventilation air may cause mildew to form
from too much moisture. See Air for Com-
bustion and Ventilation, page 5.

For convenience and efciency, install heater

• where there is easy access for operation,
inspection and service

• in coldest part of room

THERMOSTAT SENSING BULB

(Thermostat Models Only)

The thermostat sensing bulb is located below
the heater. Do not move this bulb during instal­lation or operation of the heater.

Figure 4 - Mounting Clearances As

Viewed From Front of Heater

www.fmiproducts.com

125326-01A8

INSTALLATION

Mounting

Screw

Locations

8

7

/8"

(22.5 cm)

Minimum To

Maintain 6"

(15.3 cm)
Clearance
From Wall

FLOOR

JOINING WALL

7 3/4"

(14.7 cm)

20 1/4"

(51.4 cm)

Minimum To

Maintain 3"

(7.7 cm)

Clearance

From Floor

Thin or
Thick Wall
(thick wall
shown)

Solid
Wall

1/16"
(1.6 mm)
Space

Keyhole Slots

Continued

INSTALLING HEATER TO WALL

Marking Screw Locations

WARNING: Maintain minimum

clearances shown in Figure 8. If
you can, provide greater clearanc­es from oor and joining wall.

1. Determine where you will locate heater.

2. Mark two mounting screw locations on
wall (see Figure 5).

3. Insert wall anchor (wings rst) into hole.
Tap anchor ush to wall.

4. For thin walls [1/2" (1.3 cm) or less], insert
red key into wall anchor. Push red key to
“pop” open anchor wings (see Figure 7).

IMPORTANT: Do not hammer key! For

thick walls [over 1/2" (1.3 cm) thick] or
solid walls, do not pop open wings.

5. Tighten two screws until 1/16" (1.6 mm)
space (thickness of penny) is between
screwheads and wall (see Figure 8).

Figure 6 - Folding

Anchor

Figure 7 - Popping

Open Anchor Wings

for Thin Walls

Figure 5 - Mounting Screw Locations

Installing Two Mounting Screws

Note: Wall anchors and mounting screws are
in hardware package. The hardware package
is provided with heater.

Attaching To Wall Stud Method

For attaching mounting bracket to wall studs

1. Drill holes at marked locations using 9/64"
drill bit.

2. Insert mounting screws into wall studs.

3. Tighten screws until 1/16" (1.6 mm) space

Figure 8 - Tightening Anchors

Placing Heater On Mounting Screws

1. Locate two keyhole slots on back panel
of heater (see Figure 9).

2. Place large openings of slots over scre­wheads. Slide heater down until screws
are in small portion of slots.

(thickness of penny) is beween screw­head and wall.

Attaching to wall anchor method

Follow instructions below to attach mounting
screws to hollow walls (wall areas between
studs) or solid walls (concrete or masonry).

1. Drill holes at marked locations using 5/16"

2. Fold wall anchor (see Figure 6).

125326-01A 9

drill bit. For solid walls (concrete or ma­sonry), drill at least 1 1/4" (3.2 cm) deep.

www.fmiproducts.com

Figure 9 - Location Of Keyhole Slots On

Back Panel Of Heater

INSTALLATION

Continued

Removing Front Panel Of Heater

1. Remove two screws near bottom corners
of front panel.

2. Lift straight up on grill guard until it stops.
Grill guard will slide up about 1/4".

3. Pull bottom of front panel forward, then
down.

Figure 10 - Removing Front Panel Of

Heater

Installing Bottom Mounting Screw

1. Locate bottom mounting hole. This hole is
near bottom on back panel of heater (see
Figure 11).

2. Mark screw location on wall.

3. Remove heater from wall.

4. If installing bottom mounting screw into
hollow or solid wall, install wall anchor.
Follow steps 1 through 5 under Attaching
To Wall Anchor Method, page 9. If install­ing bottom mounting screw into wall stud,
drill hole at marked location using 9/64"
drill bit.

5. Replace heater on wall.

6. Insert bottom anchor screw through back

panel into bottom anchor or drilled hole

(see Figure 11).

7. Tighten screw until heater is rmly se­cured to wall. Do not over tighten.

Note: Do not replace front panel at this

time. Replace front panel after making
gas connections and checking for leaks
(see pages 10 through 13).

Figure 11 - Installing Bottom Mounting

Screws

www.fmiproducts.com

CONNECTING TO GAS SUPPLY

WARNING: This appliance
requires a 3/8" NPT (National
Pipe Thread) inlet connection to
the pressure regulator.

WARNING: A qualied service
person must connect heater to gas
supply. Follow all local codes.

WARNING:

For natural gas, never
connect heater to private (non-utility)
gas wells. This gas is commonly
known as wellhead gas.

IMPORTANT: For natural gas, check gas line
pressure before connecting heater to gas line.
Gas line pressure must be no greater than

10.5" W.C.. If gas line pressure is higher,
heater regulator damage could occur.

CAUTION: For propane/LP
gas, never connect heater di­rectly to the propane/LP supply.
This heater requires an external
regulator (not supplied). Install
the external regulator between the
heater and propane/LP supply.

For propane/LP gas, the installer must supply
an external regulator. The external regulator will
reduce incoming gas pressure. You must reduce
incoming gas pressure to between 11" and 14"
W.C.. If you do not reduce incoming gas pres­sure, heater regulator damage could occur. Install
the external regulator with the vent pointing down
as shown in Figure 12, page 11. Pointing the vent
down protects it from freezing rain or sleet.

CAUTION: Use only new, black
iron or steel pipe. Internally-tinned
copper tubing may be used in
certain areas. Check your local
codes. Use pipe of large enough
diameter to allow proper gas vol­ume to heater. If pipe is too small,
undue loss of volume will occur.

125326-01A10

Installation must include equipment shutoff

Cap Pipe Te e
Nipple Joint

Tee Joint

Reducer
Bushing to
1/8" NPT

1/8" NPT
Plug Ta p

Pressure
Regulator

Test Gauge Connection*

Heater
Cabinet

Sediment Trap

Equipment
Shutoff
Valve *

3"
Min.

Ground
Joint
Union

3/8" NPT
Pipe
Nipple

Natural Gas

From Gas
Meter (7" W.C.
to 10.5" W.C.
Pressure)

Propane/LP

From External
Regulator
(11" W.C. to 14"
W.C. Pressure)

valve, union and plugged 1/8" NPT tap. Locate
NPT tap within reach for test gauge hook up.
NPT tap must be upstream from heater (see
Figure 13).

IMPORTANT: Install an equipment shutoff
valve in an accessible location. The equip­ment shutoff valve is for turning on or shutting
off the gas to the appliance.

Check your building codes for an special
requirements for locating equipment shutoff
valve to heater.

Apply pipe joint sealant lightly to male NPT
threads. This will prevent excess sealant from
going into pipe. Excess sealant in pipe could
result in clogged heater valves.

sealant that is resistant to liquid
petroleum (LP) gas.

Install sediment trap in supply line as shown
in Figure 13. Locate sediment trap where it
is within reach for cleaning. Locate sediment
trap where trapped matter is not likely to
freeze. A sediment trap traps moisture and
contaminants. This keeps them from going
into heater controls. If sediment trap is not
installed or is installed wrong, heater may
not run properly.

IMPORTANT: Hold the pressure regulator
with wrench when connecting it to gas pip­ing and/or ttings. Do not over tighten pipe
connection to regulator. The regulator body
could be damaged.

Propane/LP
Supply Tank

Figure 12 - Equipment Regulator with

125326-01A 11

INSTALLATION

Continued

WARNING: Use pipe joint

External

Regulator
with Vent

Pointing

Down

Vent Pointing Down

www.fmiproducts.com

Figure 13 - Gas Connection

* An equipment shutoff valve with 1/8" NPT
tap is an acceptable alternative to test gauge
connection. Purchase the optional equipment
shutoff valve from your dealer.

INSTALLATION

Equipment
Shutoff
Valve

Propane/LP
Supply Tank

Thermostat Gas Valve

Equipment
Shutoff
Valve

Gas
Meter

Thermostat Gas Valve

CHECKING GAS CONNECTIONS

WARNING: Test all gas piping

and connections, internal and
external to unit, for leaks after

installing or servicing. Correct
all leaks at once.

WARNING: Never use an

open ame to check for a leak.
Apply a noncorrosive leak detec­tion uid to all joints. Bubbles
forming show a leak. Correct all
leaks at once.

Continued

2. Pressurize supply piping system by either
opening propane/LP supply tank valve
for propane/LP gas or opening main gas
valve located on or near gas meter for
natural gas or using compressed air.

3. Check all joints from gas meter for natural
gas (see Figure 16)) or propane/LP supply
tank for propane/LP to equipment shutoff
valve (see Figure 15 or 16). Apply a non­corrosive leak detection uid to all joints.
Bubbles forming show a leak.

4. Correct all leaks at once.

Equipment
Shutoff Valve

Open

PRESSURE TESTING GAS SUPPLY
PIPING SYSTEM

Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)

1. Disconnect appliance with its appliance

2. Cap off open end of gas pipe where equip-

3. Pressurize supply piping system by either

4. Check all joints of gas supply piping system.

5. Correct all leaks at once.

6. Reconnect heater and equipment shutoff

Test Pressures Equal To or Less Than
1/2 PSIG (3.5 kPa)

1. Close equipment shutoff valve (see Fig-

CAUTION: For propane/LP
units, make sure external regula­tor has been installed between
propane/LP supply and heater.
See guidelines under Connecting
to Gas Supply, page 10.

main gas valve (control valve) and equip­ment shutoff valve from gas supply piping.
Pressures in excess of 1/2 psig will dam­age heater regulator.

ment shutoff valve was connected.

opening propane/LP supply tank valve
for propane/LP gas or opening main gas
valve located on or near gas meter for
natural gas or using compressed air.

Apply a commercial leak detection solution
to all joints. Bubbles forming show a leak.

valve to gas supply. Check reconnected
ttings for leaks.

ure 14).

www.fmiproducts.com

Closed

Figure 14 - Equipment Shutoff Valve

Figure 15 - Checking Gas Joints for

Natural Gas (actual heater may vary from

illustration)

Figure 16 - Checking Gas Joints for

Propane/LP Gas (actual heater may vary

from illustration)

125326-01A12

INSTALLATION

Continued

PRESSURE TESTING HEATER GAS
CONNECTIONS

1. Open equipment shutoff valve (see Figure

15).

2. For natural gas, open main gas valve lo­cated on or near gas meter. For propane/
LP gas, open propane/LP supply tank
valve.

3. Make sure control knob of heater is in the
OFF position.

4. Check all joints from equipment shutoff
valve to thermostat gas valve (see Figure
16 or 17). Apply a noncorrosive leak de­tection uid to all joints. Bubbles forming
show a leak.

5. Correct all leaks at once.

6. Light heater (see Operation page 15).
Check all other internal joints for leaks.

7. Turn off heater (see To Turn Off Gas to
Appliance, page 16).

8. Replace front panel.

OPERATION

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not fol-

low these instructions exactly,

a re or explosion may result
causing property damage, per­sonal injury or loss of life.

A. This appliance has a pilot which must be

lighted by hand. When lighting the pilot,
follow these instructions exactly.

B. BEFORE LIGHTING smell all around the

appliance area for gas. Be sure to smell
next to the oor because some gas is

heavier than air and will settle on the

oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not
use any phone in your building.

• Immediately call your gas supplier from
a neighbor’s phone. Follow the gas sup­plier’s instructions.

• If you cannot reach your gas supplier,
call the re department.

C. Use only your hand to push in or turn the gas

control knob. Never use tools. If the knob
will not push in or turn by hand, don’t try to
repair it, call a qualied service technician or
gas supplier. Force or attempted repair may
result in a re or explosion.

D. Do not use this appliance if any part has

been under water. Immediately call a
qualied service technician to inspect the
appliance and to replace any part of the
control system and any gas control which
has been under water.

125326-01A 13

www.fmiproducts.com

1. STOP! Read the safety information above.

2. Make sure equipment shutoff valve is fully
open.

3. Turn off any electric power to the appliance
if service is to be performed.

4. Turn control knob clockwise to the
OFF position.

5. Wait ve (5) minutes to clear out any gas.
Then smell for gas, including near the oor.
If you smell gas, STOP! Follow “B” in the
safety information, column 1. If you don’t
smell gas, go to the next step.

6. Turn control knob counterclockwise
to the PILOT position. Press in control knob
for ve (5) seconds.

7. With control knob pressed in, push down
and release ignitor button. This will light
pilot. The pilot is attached to the front of
burner. Note: You may be running this
heater for the rst time after hooking up to
gas supply. If so, you may need to press in
control knob for 30 seconds or more. This
will allow air to bleed from the gas system.
If needed, keep pressing ignitor button until
pilot lights. If ignitor does not light pilot, refer
to Troubleshooting, page 17 or contact a
qualied service person or gas supplier for
repairs. Until repairs are made, light pilot
with match. To light pilot with match, see
Manual Lighting Procedure, page 14.

8. Keep control knob pressed in for 30 sec­onds after lighting pilot. After 30 seconds,
release control knob.

• If control knob does not pop out when
released, contact a qualied service person
or gas supplier for repairs.

LIGHTING

INSTRUCTIONS

Control
Knob

O

O

T

Control
Knob

Note: If pilot goes out, repeat steps 4

Thermocouple

Ignitor Electrode

Pilot Burner

9. Turn control knob counterclockwise

10. To shut off burners only and leave pilot lit,

manual control heaters at the

locked positions. Operation
between these positions may
create a possible health hazard
if used in a poorly ventilated
room. Read owner’s manual for
complete instructions.

Figure 19 - Pilot (actual pilot may vary)

just heating levels by using the
equipment shutoff valve.

OPERATION

Continued

through 7. Wait one (1) minute before light­ing pilot

to desired heating level. The main burner
should light.

turn control knob clockwise to the
PILOT position.

WARNING: Always operate

Figure 17 - Control Knob in the OFF

Position for Manual Control Models

Figure 18 - Control Knob in the OFF

Position for Thermostat Models

CAUTION: Do not try to ad-

TO TURN OFF GAS

TO APPLIANCE

1. Turn control knob clockwise to the
OFF position.

2. Turn off all electric power to the appliance
if service is to be performed.

2. Close equipment shutoff valve (see Figure
15, page 13).

MANUAL LIGHTING

PROCEDURE

1. Remove front panel (see Figure 6, page 9).

2. Follow steps 1 through 5 under Lighting
Instructions, page 15.

3. With control knob pressed in, strike match.
Hold match to pilot until pilot lights.

4. Keep control knob pressed in for 30 sec­onds after lighting pilot. After 30 seconds,
release control knob. Now follow step 9
under Lighting Instructions, page 15.

5. Replace front panel.

THERMOSTAT CONTROL

OPERATION

Thermostat models only

The thermostatic control used on these
models differs from standard thermostats.
Standard thermostats simply turn on and off
the burner. The thermostat used on this heater
senses the room temperature. At times the
room may exceed the set temperature. If so,
the burner will shut off. The burner will cycle
back on when room temperature drops below
the set temperature. The control knob can be
set to any comfort level between 1 and 5. All
plaques will turn off and on.

Note: The thermostat sensing bulb mea­sures the temperature of air near the heater
cabinet. This may not always agree with
room temperature (depending on housing
construction, installation location, room size,
open air temperatures, etc.) Frequent use of
your heater will let you determine your own
comfort levels.

www.fmiproducts.com

125326-01A14

1

/2 Glass

Height

1

/2 Glass

Height

Blue
Flame

Yellow
Tipping

1

/2 Glass

Height

Yellow
Tipping

INSPECTING HEATERS

Thermocouple

Pilot Burner

Pilot Burner

Thermocouple

Blue Flame

Yellow Flame

Check pilot ame pattern and burner ame
patterns often.

PILOT FLAME PATTERN

Figure 20 shows a correct pilot ame pattern.
Figure 21 shows an incorrect pilot ame pat­tern. The incorrect pilot ame is not touching the
thermocouple. This will cause the thermocouple
to cool. When the thermocouple cools, the
heater will shut down.

If pilot ame pattern is incorrect, as shown
in Figure 21

• turn heater off (see To Turn Off Gas to Ap-
pliance, page 14)

• see Cleaning and Maintenance, page 16

Note: The pilot ame on natural gas units will

have a slight curve, but ame should be

blue and have no yellow or orange color.

Figure 20 - Correct Pilot Flame Pattern

BURNER FLAME PATTERN

WARNING: If yellow tipping
occurs, your heater could pro­duce increased levels of carbon
monoxide.

NOTICE: Do not mistake orange
ames with yellow tipping. Dirt
or other ne particles enter the
heater and burn causing brief
patches of orange ame.

Figure 22 shows a correct burner ame pattern.
Figure 23 shows an incorrect burner ame pat­tern. The incorrect burner ame pattern shows
yellow tipping of the ame. It also shows the
ame higher than 1/2 the glass panel height.

If burner ame pattern is incorrect, as shown
in Figure 23

• turn heater off (see To Turn Off Gas to Ap-
pliance, page 14)

• see Cleaning and Maintenance, page 16

Figure 21 - Incorrect Pilot Flame Pattern

125326-01A 15

Figure 22 - Correct Burner Flame Pattern

Figure 23 - Incorrect Burner Flame

Pattern

www.fmiproducts.com

CLEANING AND MAINTENANCE

WARNING: Turn off heater

and let cool before cleaning.

CAUTION: You must keep
control areas, burner and circu­lating air passageways of heater
clean. Inspect these areas of
heater before each use. Have
heater inspected yearly by a
qualied service person. Heater
may need more frequent clean­ing due to excessive lint from
carpeting, bedding material, pet
hair, etc.

WARNING: Failure to keep
the primary air opening(s) of
the burner(s) clean may result in
sooting and property damage.

ODS/PILOT AND BURNER

Use a vacuum cleaner, pressurized air or
small, soft bristled brush to clean.

BURNER PILOT AIR INLET

The primary air inlet holes allow the proper
amount of air to mix with the gas. This pro­vides a clean burning ame. Keep these holes
clear of dust, dirt and lint. Clean these air inlet
holes prior to each heating season. Blocked
air holes will create soot. We recommend that
you clean the unit every three months during
operation and have heater inspected yearly
by a qualied service person.

We also recommend that you keep the burner
tube and pilot assembly clean and free of dust
and dirt. To clean these parts we recommend
using compressed air no greater than 30 PSI.
Your local computer store, hardware store or

home center may carry compressed air in a

can. If using compressed air in a can, please
follow the directions on the can. If you don’t
follow directions on the can, you could dam­age the pilot assembly.

1. Shut off unit, including pilot. Allow unit to
cool for at least thirty minutes.

2. Inspect burner, pilot and primary air inlet
holes on orice holder for dust and dirt
(see Figure 26).

3. Blow air through the ports/slots and holes
in the burner.

4. Never inset objects into the pilot tube.

5. Blow air into the primary air holes on the
orice holder.

Clean pilot assembly also. A yellow tip on the
pilot ame indicates dust and dirt in the pilot
assembly. There is a small pilot air inlet hole
about 2" from where the pilot ame comes out
of the pilot assembly (see Figure 26). With the
unit off, lightly blow air through the air inlet
hole. You may blow through a drinking straw
if compressed air is not available.

Pilot
Assembly

Pilot Air

Inlet Hole

Figure 26 - Pilot Inlet Air Hole

CABINET

Air Passageways

Use pressurized air to clean.

Exterior

Use a soft cloth dampened with a mild soap
and water mixture. Wipe the cabinet to re­move dust.

www.fmiproducts.com

125326-01A16

TROUBLESHOOTING

WARNING: Turn off and unplug heater and let cool before servicing.

Only a qualied service person should service and repair heater.

CAUTION: Never use a wire, needle or similar object to clean

ODS/pilot. This can damage ODS/pilot unit.

Note: All troubleshooting items are listed in order of operation.

OBSERVED PROBLEM

Whe n i g n i t or butt o n i s
pressed, there is no spark at
ODS/pilot

POSSIBLE CAUSE

1. Ignitor electrode positioned
wrong

2. Ignitor electrode broken

3. Ignitor electrode not con-

nected to ignitor cable

4. Igni tor cable pinched or
wet

5. Broken ignitor cable

6. Bad piezo ignitor

REMEDY

1. Replace pilot assembly

2. Replace pilot assembly

3. Reconnect ignitor cable

4. Free ignitor cable if pinched
by any metal or tubing. Keep

ignitor cable dry

5. Replace ignitor cable

6. Replace piezo ignitor

When ignitor button is pressed
in, there is a spark at ODS/Pilot
but no ignition

1. Gas supply turned off or
equipme nt shu to ff valve

closed

2. Control knob is not in pilot

position

3. Cont r o l knob n o t ful l y
pressed in while pressing
ignitor button

4. Air in gas lines when in-

stalled

5. Depleted gas supply (pro­pane/LP gas)

6. ODS/pilot is clogged

7. Gas regulator setting is not

correct

1. Turn on gas supply or open
equipment shutoff valve

2. Turn control knob to pilot

position

3. Turn to PILOT/IGN posi­tion. Fully press in control
knob while pressing ignitor
button

4. Cont inu e holdi ng do wn
control knob. Repeat ignit­ing ope ra ti on until a ir is
removed

5. Contact local propane/LP

gas company

6. Clean ODS/pilot (see Clean­ing and Maintenance, page

16) or replace ODS/pilot

assembly

7. Replace gas regulator

125326-01A 17

www.fmiproducts.com

OBSERVED PROBLEM

ODS/pilot lights but flame
goes out when control knob

is released

TROUBLESHOOTING

Continued

POSSIBLE CAUSE

1. Cont r ol kn o b not f ully

pressed in

2. Control knob not pressed in
long enough

3. Equipment shutoff valve not
fully open

4. Pilot flame not touchi ng
thermocouple, which al­lows thermocouple to cool,
causing pilot ame to go
out. This problem could be
caused by one or both of
the following:

A) Low gas pressure
B) Dirty or partially clogged

ODS/pilot

5. Thermocouple connection
loose at control valve

6. Thermocouple damaged

7. Control valve damaged

REMEDY

1. Press in control knob fully

2. After ODS/pilot lights, keep
control knob pressed in 30

seconds

3. Fully open equipment shut­off valve

4. A) Contact local natural or
propane/LP gas company

B) Clean ODS/pilot (see

Cleaning and Maintenance,
page 16) or replace ODS/

pilot assembly

5. Hand tighten until snug,
then tighten 1/4 turn more

6. Replace pilot assembly

7. Replace control valve

Burner does not light after
ODS/pilot is lit

Delayed ignition of burner

Burner backring during com­bustion

1. Burner orice clogged

2. Inlet gas pressure is too
low

1. Manifold pressure is too
low

2. Burner orice clogged

1. Burner orice is clogged or

damaged

2. Damaged burner

3. Gas regulator defective

1. Clean burner (see Cleaning
and Maintenance, page 16)
or replace burner orice

2. Contact loca l natural or
propane/LP gas company

1. Contact loca l natural or
propane/LP gas company

2. Clean burner (see Cleaning
and Maintenance, page 16)
or replace burner orice

1. Clean burner (see Cleaning
and Maintenance, page

16)

2. Replace burner

3. Replace gas regulator

www.fmiproducts.com

125326-01A18

OBSERVED PROBLEM

Yellow ame during burner
combustion

TROUBLESHOOTING

Continued

POSSIBLE CAUSE

1. Not enough air

2. Gas Regulator defective

3. Clogged or dirty burner

REMEDY

1. Clean burner (see Cleaning
and Maintenance, page 16)

or replace burner orice

2. Replace damaged burner

3. Replace gas regulator

Slight smoke or odor during

initial operation

Heater produces a clicking/
ticking noise just after burner
is lit or shut off

White powder residue forming
within burner box or on adja­cent walls or furniture

Heater produces a whistling
noise when burner is lit

1. Residues from manufactur-

ing processes

1. Met al exp a ndi ng whi l e
heating or contracting while

cooling

1. When heated, vapors from
furniture polish, wax, carpet
cleaner, etc., may turn into
white powder residue

1. Turning control knob to po­sition when burner is cold

2. Air in gas line

3. Air passageways on heater
blocked

4. Dirty or partially clogged
burner orice

1. Problem will stop after a few
hours of operation

1. This is normal with most heat­ers. If noise is excessive, con­tact qualied service person

1. Turn heater off when using

furniture polish, wax, carpet

cleaners or similar products

1. Turn control knob to 1 posi­tion and let warm up for a
minute.

2. Operate burner until air is
removed from line. Have gas
line checked by local natural
or propane/LP gas company

3. Observe minimum installa­tion clearances (see Figure
4, page 8)

4. Clean burner (see Cleaning
and Maintenance, page 16)
or replace burner orice

125326-01A 19

www.fmiproducts.com

TROUBLESHOOTING

Continued

WARNING: If you smell gas

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Fol­low the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning sup­plies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc.,
create fumes. These fumes may mix with combustion air and create odors.

OBSERVED PROBLEM

Heater produces unwanted

odors

Heater shuts off in use (ODS
operates)

Gas odor even when control
knob is in OFF position

Gas odor during combustion

Moisture/condensation no­ticed on windows

POSSIBLE CAUSE

1. Heater burning vapors from paint,
hair spray, glues, etc. See IM-
PORTANT statement above

2. Low fuel supply (propane/
LP gas only)

3. Gas leak. See Wa rning

statement at top of page

1. No t en ou gh fre sh air is
available

2. Low line pressure

3. ODS/pilot is partially clogged

1. Gas leak. See Wa rning

statement at top of page

2. Control valve defective

1. Foreign matter between
control valve and burner

2. Gas leak. See Wa rning

statement at top of page

1. Not enough combustion/
ventilation air

REMEDY

1. Ventilate room. Stop using
odor causing products while

heater is running

2. Rell supply tank

3. Locate and correct all leaks
(see Checking Gas Connec-
tions, page 12)

1. Open window and/or door for
ventilation

2. Contact local natural or pro­pane/LP gas company

3. Clean ODS/pilot (see Cleaning
and Maintenance, page 16)

1. Locate and correct all leaks
(see Checking Gas Connec-
tions, page 12)

2. Replace control valve

1. Take apart gas tubing and
remove foreign matter

2. Locate and correct all leaks
(see Checking Gas Connec-
tions, page 12)

1. Refer to Air for Combustion
and Ventilation requirements
(page 5)

www.fmiproducts.com

125326-01A20

SPECIFICATIONS

GWN10A, VSHN10M

• Natural Gas Only

• 5,500/10,000 Btu/h

• Piezo Ignition

• Pressure Regulator Setting: 3" W.C.

• Inlet Gas Pressure* (in. of water):
Maximum - 10.5" W.C., Minimum - 4" W.C.

GWN10TA, VSHN10T

• Natural Gas Only

• 5,000/10,000 Btu/h

• Piezo Ignition

• Pressure Regulator Setting: 3" W.C.

• Inlet Gas Pressure* (in. of water):
Maximum - 10.5" W.C., Minimum - 4" W.C.

REPLACEMENT PARTS

Note: Use only original replacement parts.
This will protect your warranty coverage for

parts replaced under warranty.

Contact authorized dealers of this product.
If they can’t supply original replacement
pa r t(s ), ca l l FMI PR ODU CTS , LLC at
1-866-328-4537.

GWP10A, VSHP10M

• Propane/LP Gas Only

• 5,500/10,000 Btu/h

• Piezo Ignition

• Pressure Regulator Setting: 8" W.C.

• Inlet Gas Pressure* (in. of water):
Maximum - 14" W.C., Minimum - 11" W.C.

GWP10TA, VSHP10A

• Propane/LP Gas Only

• 5,000/10,000 Btu/h

• Piezo Ignition

• Pressure Regulator Setting: 8" W.C.

• Inlet Gas Pressure* (in. of water):
Maximum - 14" W.C., Minimum - 11" W.C.

When calling, have ready:

• your name

• your address

• model and serial numbers of your heater

• how heater was malfunctioning

• type of gas used (propane/LP or natural
gas)

• purchase date

Usually, we will ask you to return the part to
the factory.

TECHNICAL SERVICE

You may have further questions about installa­tion, operation or troubleshooting. If so, contact
FMI PRODUCTS, LLC at 1-866-328-4537.
When calling please have your model and
serial numbers of your heater ready.

You can also visit our web site at
www.fmiproducts.com.

125326-01A 21

www.fmiproducts.com

When Gas Pressure Is Too Low

• pilot will not stay lit

• burners will have delayed ignition

• heater will not produce specied heat

• propane/LP gas supply may be low

You may feel your gas pressure is too low. If
so, contact your local natural or propane/LP
gas supplier.

SERVICE HINTS

PARTS

1

2

3

4*

5

6

7*

8*

9*

10

11

12

13

14

15

16

17

18

19

20

4**

9**

7**

8**

*Manual Models
**Thermostat Models

MODELS GWN10A, GWP10A, GWN10TA, GWP10TA, VSHN10M,
VSHP10M, VSHN10T, VSHP10T

www.fmiproducts.com

125326-01A22

This list contains replaceable parts used in your heater. When ordering parts, follow the

PARTS

instructions listed under Replacement Parts on page 21 of this manual.

KEY

NO. PART NO. DESCRIPTION

GWP10TA

VSHP10T

GWN10TA

VSHN10T

GWP10A

VSHP10M

GWN10A

VSHN10M QTY.

1 099217-02CP Front Panel • • • • 1
2 098271-03 Ignitor Cable • • • • 1
3 097159-04 Piezo Ignitor • • • • 1
4 099413-01 Control Valve • 1

099413-02 Control Valve • 1

098522-11 Control Valve • 1

098522-18 Control Valve • 1
5 098508-01 Valve Nut Retainer • • 1
6 099393-02 Control Knob • • 1
7 099462-01 Burner Tube • • 1

104261-01 Burner Tube • • 1
8 099391-02 Regulator Tube • • 1

104264-01 Inlet Tube • • 1
9 099387-17 Pilot Tube • • 1

099387-11 Pilot Tube • • 1
10 099317-02 Deector • • • • 1
11 NJF 8C Hex Nut • • • • 1
12 104259-01 Orice • 1

104259-02 Orice • 1
104259-05 Orice • 1

104259-06 Orice • 1
13 104263-03 Burner • • • • 1
14 120630-03 ODS/Pilot • • 1

120630-02 ODS/Pilot • • 1
15 099318-04 Grill Guard • • • • 1
16 099319-02 Top Glass Retainer • • • • 1
17 098260-11 Glass Panel • • • • 1
18 102017-02 Bottom Glass Retainer • • • • 1
19 099415-17 Gas Regulator • • 1

099415-18 Gas Regulator • •
20 ** Cabinet Assembly • • • • 1

PARTS AVAILABLE - NOT SHOWN

100642-02 Hardware Assembly • • • • 1

125332-01 Lighting Instruction • • 1

125333-01 Control Position Decal • • 1

107888-06 Control Position Decal • • 1

099123-01 Thermobulb Clip • • 1

** Not a eld replaceable part.

125326-01A 23

www.fmiproducts.com

WARRANTY

kEEP THIS WARRANTY

Model (

located on product or identication tag

Serial No. (

located on product or identication tag

Date Purchased __________________________

Keep receipt for warranty verication.

FMI PRODUCTS, LLC LIMITED WARRANTIES

Standard Warranty: FMI PRODUCTS, LLC warrants this new product and any parts thereof to be free from defects
in material and workmanship for a period of four (4) years from the date of rst purchase from an authorized dealer
provided the product has been installed, maintained and operated in accordance with FMI PRODUCTS, LLC’s
warnings and instructions.

For products purchased for commercial, industrial or rental usage, this warranty is limited to 90 days from the date
of rst purchase.

Limited Warranty: FMI PRODUCTS, LLC warrants factory reconditioned products and any parts thereof to be
free from defects in material and workmanship for 30 days from the date of rst purchase from an authorized dealer
provided the product has been installed, maintained and operated in accordance with FMI PRODUCTS, LLC’s
warnings and instructions.

The following terms apply to all of the above warranties:

Always specify model number and serial number when contacting the manufacturer. To make a claim under this
warranty the bill of sale or other proof of purchase must be presented.

This warranty is extended only to the original retail purchaser when purchased from an authorized dealer, and only
when installed by a qualied installer in accordance with all local codes and instructions furnished with this product.

This warranty covers the cost of part(s) required to restore this product to proper operating condition and an allow­ance for labor when provided by a FMI PRODUCTS, LLC Authorized Service Center or a provider approved by
FMI PRODUCTS, LLC. Warranty parts must be obtained through authorized dealers of this product and/or FMI
PRODUCTS, LLC who will provide original factory replacement parts. Failure to use original factory replacement
parts voids this warranty.

Travel, handling, transportation, diagnostic, material, labor and incidental costs associated with warranty repairs,
unless expressly covered by this warranty, are not reimbursable under this warranty and are the responsibility of
the owner.

Excluded from this warranty are products or parts that fail or become damaged due to misuse, accidents, improper
installation, lack of proper maintenance, tampering, or alteration(s).

This is FMI PRODUCTS, LLC’s exclusive warranty, and to the full extent allowed by law; this express warranty
excludes any and all other warranties, express or implied, written or verbal and limits the duration of any and all
implied warranties, including warranties of merchantability and tness for a particular purpose to four (4) years on
new products and 30 days on factory reconditioned products from the date of rst purchase. FMI PRODUCTS, LLC
makes no other warranties regarding this product.

FMI PRODUCTS, LLC’s liability is limited to the purchase price of the product, and FMI PRODUCTS, LLC shall not
be liable for any other damages whatsoever under any circumstances including indirect, incidental, or consequential
damages.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental
or consequential damages, so the above limitation or exclusion may not apply to you.

This warranty gives you specic legal rights, and you may also have other rights which vary from state to state.

For information about this warranty contact:

Factory Reconditioned Products

Terms Common to All Warranties

) _____________________________

) __________________________

New Products

2701 S. Harbor Blvd.

Santa Ana, CA 92704

1-866-328-4537

www.fmiproducts.com

125326-01

Rev. A
05/10