FLYTECH TECHNOLOGY LS185100 User Manual

U

ser

M

File name: LS1851_Series_User Manual_B78 68_UL 60601 V1
5-LS185120100713
Control number: LS185120100713
Revision: v1.5

anual

Bedside Terminal

Hardware

System LS1851

Copyright 2010 July
All Rights Reserved
Manual Version 1.5
P/N:

The information contained in this document is subject to change
without notice.
We make no warranty of any kind with regard to this material,
including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. We shall not be
liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of
this material.

This document contains proprietary information that is protected by
copyright. All rights are reserved. No part of this document may be
photocopied, reproduced or translated to another language without
the prior written consent of the manufacturer.

TRADEMARK

Intel®, Pentium® and MMX are registered trademarks of Intel®
Corporation. Microsoft® and Windows® are registered trademarks
of Microsoft Corporation.
Other trademarks mentioned herein are the property of their
respective owners.

i

Safety

IMPORTANT SAFETY INSTRUCTIONS

1. To disconnect the machine from the electrial power supply, turn
off the power switch and remove the power cord plug from the
wall socket. The wall socket must be easily accessible and in
close proximity to the machine.

2. Read these instructions carefully. Save these instructions for
future reference.

3. Follow all warnings and instructions marked on the product.

4. Do not use this product near water.

5. Do not place this product on an unstable cart,stand,or table.The
product may fall, causing serious damage to the product.

6. Slots and openings in the cabinet and the back or bottom are
provided for ventilation;to ensure reliable operation of the product
and to protect it from overheating. These openings must not be
blocked or covered.The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar
surface.This product should never be placed near or over a
radiator or heat register,or in a built-in installation unless proper
ventilation is provided.

7. This product should be operated from the type of power indicated
on the marking label.If you are not sure of the type of power
available, consult your dealer or local power company.

8. Do not allow anything to rest on the power cord. Do not locate this
product where persons will walk on the cord.

9. Never push objects of any kind into this product through cabinet
slots as they may touch dangerous voltage points or short out
parts that could result in a fire or electric shock. Never spill liquid
of any kind on the product.

ii

CE MARK

“Low Voltage Directive”.

FCC

This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that

This device complies with the requirements of the
EEC directive 2004/108/EC with regard to
“Electromagnetic compatibility” and 2006/95/EC

may cause undesired operation.

Federal Communications Commission statement
This equipment has been tested and found to comply with the limits for a class
B digital device,
pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential
installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is
encouraged to try to correct the interference by one or more
of the following measures:

˙Reorient or relocate the receiving antenna.

˙Increase the separation between the equipment and receiver.

iii

˙Connect the equipment into an outlet on a circuit different from that to which
the receiver is
connected.
˙Consult the dealer or an experienced radio/TV technician for help.
.interference that may cause undesired operation.

UL

CAUTION ON LITHIUM BATTERIES

There is a danger of explosion if the battery is replaced incorrectly.
Replace only with the same or equivalent type recommended by the
manufacturer. Discard used batteries according to the manufacturer’s
instructions.

LEGISLA TION AND WEEE SYMBOL

2002/96/EC Waste Electrical and Electronic Equipment Directive
on the treatment, collection, recycling and disposal of electric
and electronic devices and their components.

iv

The crossed dustbin symbol on the device means that it should not be
disposed of with other household wastes at the end of its working life.
Instead, the device should be taken to the waste collection centers for
activation of the treatment, collection, recycling and disposal
procedure.
To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this from other types of
wastes and recycle it responsibly to promote the sustainable reuse of
material resources.

Household users should contact either the retailer where they
purchased this product, or their local government office, for details of
where and how they can take this item for environmentally safe
recycling.

Business users should contact their supplier and check the terms and
conditions of the purchase contract.

This product should not be mixed with other commercial wastes for
disposal.

CAUTION SYMBOL IN CARTON

v

Attention

Attention, consult ACCOMPANYING DOCUMENTS

You are cautioned that changes or modifications not expressly approved by the
part responsible for compliance could void the user’s authority to operate the

equipment.

vi

Revision History

Changes to the original user manual are listed below:

Version Date Description

1.0 2009 July Initial release

1.1 2009 Sep Add Arm installation

1.2 2009 Sep

1.3 2010 May

1.4 2010 July Cleaning solution-Wipe with clean water.

1.5 2010 July

Add Arm application condition
Modified connector wording

B68 motherboard added
Jumper Setting updated

1. Add model number (page 1).

2. Add system weight including base, page 32).

3.Base installation (Page 31)

4. UL mark modified(Page 4 )

5. Cleaning method (Page 33).

6. Caution symbol(Page 6)

7. Add File and control number(Page 1)

8. Remove nurse call wording(Page 32 )

9. Remove mount description(Page 33)

10. Humidity range modified (Page 33)

11.Add attention mark (Page 6)

12.Add power adapter fuse spec(Page 33)

vii

Table Contents

1 Item Checklist......................................1

1-1 Standard Items ..........................................................1

2 System View........................................2

2-1 Front View .................................................................2

2-2 Rear View..................................................................3

2-3 Side View...................................................................4

2-4 I/O View.....................................................................5

2-5 Stand .........................................................................6

3 Driver Installation.................................7

3-1 Driver List ..................................................................7

3-2 Chipset Driver Installation..........................................8

3-3 USB 2.0 Driver Installation.........................................9

3-4 VGA Driver Installation.............................................12

3-5 Audio Driver Installation...........................................13

3-6 10/100/1000MB LAN Driver Installation...................14

3-7 ELO Touch Driver Installation ..................................15

3-8 POSTouch Driver Installation...................................18

4 Peripheral Installation........................22

4-1 Phone Set Installation..............................................22

4-2 Stand Installation .....................................................23

5 Specification......................................24

6 Jumper Settings ................................26

6-1 B78 motherboard.....................................................26

6-2 B68 Motherboard.....................................................30

7 BIOS Settings....................................35

viii

7-1 BIOS Setup Utility....................................................35

7-2 Starting the BIOS Setup...........................................35

7-3 When a Problem Occurs..........................................35

7-4 BIOS Main Menu.....................................................35

1 Item Checklist

Take the system unit out of the carton. Remove the unit from the carton by holding it
by the foam inserts. The following contents should be found in the carton:

1-1 Standard Items

Driver CD Manual

Power Adapter

Power Cable

System Phone Module

1

2 System View

2-1 Front View

④

①

②

③

System Overview table -1

Number Component

1 Camera
2 TV Key pad (Power , volume and channel button)
3 Smart card reader slot
4 Phone set holder

2

2-2 Rear View

①

⑦

④

⑥

⑤

②

③

⑧ ⑧

System Overview Table -2

Number Component

1 Ventilation
2 VESA Holes
3 Rear I/O (USBx2, DC-IN, RJ48 , LAN Connector)
4 Phone Set Holder
5 RFID Sensor
6 Smart Card Reader Slot
7 MSR Slot (Option)
8 Speakers

3

2-3 Side View

①

②

System Overview Table -3

Number Component

1 Smart Card Reader Slot
2 MSR Slot (Option)

4

2-4 I/O View

② ③

⑤ ⑥

①

⑦

⑧

System Overview Table -4

Number Component Description

1 USB x 2
2 SCSI Connector
3 USB x 1
4 Phone Jack (RJ11)
5 Audio Line-out
6 Audio MIC-IN
7 Built-in MIC

④

8 Smart Card Reader Slot

5

2-5 St and

6

3 Driver Installation

3-1 Driver List

B78 V2.2 Driver List

Folder/File File Description

<CD>:\ POS360_B78.htm Driver List
<CD>:\COMMON\INTEL\Chipset\i8xx Chipset Driver
<CD>:\COMMON\INTEL\USB20 USB 2.0 Driver
<CD>:\COMMON\INTEL\VGA\i85x VGA Driver
<CD>:\COMMON\Ac97_codec\Realtek\ALC202A Audio Driver
<CD>:\COMMON\ POS_Touch POSTouch Driver
<CD>:\COMMON\ELO_Touch ELO Touch Driver
<CD>:\COMMON\Lan_driver\Realtek_PCI 10/100/1000Mb LAN Driver

-The following procedures are for Windows 2000/XP, other platforms are similar.

7

3-2 Chipset Driver Installation

a. Click “Chipset” in the Driver List menu

of POS360 B78.

c. Click the “Next” button on the

Welcome window.

b. Double-click

“infinst_enu_6.0.1.1002.exe” on the
My computer window.

d. Click the “Yes” button on the License

Agreement window.

8

e. Click the ”Next” button on the Readme

Information window.

f. Click the “Finish” button and restart

your system.

3-3 USB 2.0 Driver Installation

OS Requirements

OS USB 2.0 requirements

Windows XP

Windows 2000

Windows 98SE/Me USB 2.0 drivers are available on the Intel developer site.

Windows 98
(Retail)

Linux

USB 2.0 drivers are provided in Service Pack 1 (SP1) for
Windows XP, which is available through Windows Updat e.

USB 2.0 drivers are available through Windows Update or
Service Pack 4.

Developers and OEMs should contact Orange Ware. For
end-users, if your device does not ship with Windows 98
drivers, contact your device or system manufacturer. If
USB 2.0 drivers are not available, your device will operate
at USB 1.1 speeds

USB 2.0 support is available in kernel 2.4.19 or later
development kernels, or in the 2.4.19 or later production
kernel. More information.

9

a. Right click My Computer on the

desktop and select “properties”

b. Select “Hardware””Device

Manager” on system properties

c. Select ”Other Devices”  “Universal Serial Bus (USB) Controller” ”Properties” on

Device Manager

10

d. Select “Device” “Update Driver e. Click the ”Next” button on the

welcome window.

f. Select “Search for a suitable…”and

click the “Next” button on the Install
Hardware Device Drivers window

g. Select “Specify a location” and click

the “Next” button on the Locate Driver
Files window.

h. Press “Browse” to select the driver

and then click the “OK” button to go to

i. Click the “Next” button on the Driver

Files Search Results window.

the next page

j. Click the “Finish” button to complete

k. Finished.

this process.

11

3-4 VGA Driver Installation

a. Click “Win2K_XP” of “VGA” section in

the Driver List menu.

c. Click the “Next” button on the Intel(R)

Chipset Graphics Driver Software­Install Shield(R) Wizard dialog.

b. Click “Run” when the “File Download –

Security Warning” dialog pops up.

d. Click the “Next” button on the Intel(R)

Graphics Media Accelerator Driver
dialog.

e. Click the “Yes” button on the Intel(R)

Graphics Media Accelerator Driver
dialog.

f. Select “Yes, I want to restart my

computer now” and click the “Finish”
button on the Intel(R) Graphics Media
Accelerator Driver dialog.

12

3-5 Audio Driver Installation

a. Click “Win9X,ME,2K_XP” of the

“Audio” section in the Driver List menu.

c. Double-click “wdm_a371.exe” on the

My Computer window.

b. Double-click “A3.71” on the My

Computer window.

d. Click “Next” button on the Realtek

AC’97 Audio Setup window.

e. Click “Yes” button on the Digital

Signature Not Found window.

f. Click “Finish” button on the Realtek

AC’97 Audio Setup window.

13

3-6 10/100/1000MB LAN Driver Installation

a. In the “Realtek RTL8110” section,

click on Win9X, ME, 2K, XP

c. Double-click Setup.exe d. Click the Finish button on the

b. Double-click “v709”

Maintenance Complete window.

e. Click the OK button and restart your

system.

14

3-7 ELO Touch Driver Installation

a. In the “ELO” section, click on

“Windows”.

b. Click “Install Touch Driver” on “FT

Touch Auto Install V1.0.2.0” window to
detect the touch type in your system.

c. Click “Install Touch Driver”.

e. Click “Browse” button to identify a

location or folder name to save to.
Click “Unzip” button to extract the
files.

d. A “WinZip Self-Extractor” dialog will

pop up. Click “OK”.

f. Finished unzipping. Click “OK”.

15

g. Click “Next”. h. Check the “Install Serial Touchscreen”

Drivers” check box and click “Next”.

i. Click “Yes” to accept the “End User

License Agreement”.

j. Examining serial ports on the

computer

k. Check the box “Auto-detect Elo

devices” and click “Next”.

l. The computer is searching for a

connected to Elo Touchscreen

16

m. Touchscreen found on “COM5”.

Click “Next”.

n. Click “Next” to complete the driver

installation

o. Driver is installing p. The driver installation and setup are

now complete. Click “Finish” to start
the touchscreen calibration.

q. Follow the instructions on the screen

to calibrate the Touchscreen.

r. Verify that the touchscreen is working

correctly by moving your finger on the
screen. The mouse cursor should
follow your finger. Finally, touch the
green checkmark to save the
calibration settings and exit the
program

17

3-8 POSTouch Driver Installation

a. In the “Touch Screen auto…” section,

click “Windows”.

b. Click “Install Touch Driver” on “FT Touch

Auto Install V1.0.2.0” window to detect
the touch type in your system.

c. “FT Touch Auto Install” program will

detect what touch type and interface
being installed on the system.

e. Select ”I agree…” and click ”Next”.

d. Click ”Next”.

f. Select the installation folder for the

touch utility driver and click ”Next”.

18

g. Select the shortcut folder for the touch

h. Click ”Next”.

utility driver and click ”Next”.

i. Click ”Next”.

j. The computer is installing the touch

driver

k. Click ”Continue Anyway” button.

l. The serial ports are scanned for a touch

device. The Touch panel is on COM5.

19

m. Click ”Finish”.

n. Click ”OK” to restart the computer and

finish the touch utility installation.

o. The computer has restarted. Click on

p. Select the Device tab.
the ”Start” button, select “Programs”,
then select ”Touchutility”.

q. Click on the 3 points or the 9 points

calibration button.

r. Follow the instructions on the screen to

do the calibration of the touch panel

20

s. Touch anywhere on the screen to save

the calibration.

21

4 Peripheral Installation

4-1 Phone Set Installation

a. Slide the Phone module into the Phone set holder as the direction of arrow

shows.

b. Connect the phone cable to the connector on the Phone module.

c. Connect the other end of the Phone cable to the connector on the System.

22

4-2 Stand Installation

a. Four M6x10 screw for stand installation.

23

5 Specification

Model Name Bedside Terminal

Motherboard B78 v2.2 B68 v1.0

CPU Supports

Celeron M ULV 1.0GHz,

512kb cache

Chipset Intel 852GM and ICH4 FSB 400Mhz

System Memory 2 x DDR SO-DIMM slot, up to 2 GB 2 x DDRII SO-DIMM slot, up to 2GB
Graphic Memory Share system memory max 64MB Share system memory max 224MB

LCD / Touch Panel

LCD Size 18.5" TFT LCD
Brightness 300nits
Maximal Resolution 1366x 768
Touch Screen Type Resistive touch(USB interface)

Storage

HDD 2.5" Slim HDD bay, SATA HDD

Expansion

mini-PCI Slot 1, support 802.11 b/g,a/b/g WLAN card

External I / O Ports

Intel Atom N270 proce s sor 1.6GHz

L2 512K

Intel 945GSE Express

and ICH7M FSB 533MHz

USB 2.0 3 x USB Type A
Audio Jack 1 x MIC-in, 1 x Line-out

Handset Jact

1 x RJ-11

(Not connected to telecommunication system)

Remote control 1 x SCSI 26pin

Interfaces accessible via secure / hidden arm access panel

RJ48 system

1 x RJ-48

(Not connected to telecommunication system)

Ethernet connection
10/100/1000MB
USB 2.0 2 x USB Type A
Power input

Audio

Speaker 2 x 3W Speaker

Power

Power Adapter DC 19V / 90W

1 x RJ-45

19V DC / 4.74A

24

Environment

EMC & Safety FCC Class B, CE, LVD
Operating Temperature 0°C ~ 35°C (32°F ~ 95°F)
Storage Temperature -20° ~ 60°C (-4°F ~ 140°F)
Operating Humidity 30% - 93% RH non-condensing
Storage Humidity 30% - 93% RH non-condensing
Altitude during operation An atmospheric PRESSURE range of 700 hP a to 1060 hPa.
Dimension (W x D x H)

Weight

9.6 kg including telephone cradle and handset and Stand (max)

Power supplier

462 .5x 336 x 75 (mm) (Without handset)

6.8 kg including telephone cradle and handset (max)

100~240VAC to 19V DC (90W) power brick

Input voltage: 100~240VAC
Input frequency: 47 to 63 Hz
Input current: 1.06 to 0.45 A

Power Brick

Output voltage:19V

Output current: 4.74A

Output power: 90W max

Supply Class I adapter equipment of IPX0 classification continuous

Supplier: CONQUER P/N:MST2.50

Power adapter fuse

OS Support

Optional Additional Features (Note: options which can be retro-fitted to be advised)

Camera (Build in) 1.3M pixels CCD came ra module

Supplier: BEL FUSE P/N:RST2.5

Rate voltage:250V

Rated current: 2.5A

Windows-XP / Linux

Magnetic stripe card
reader(Optional)
Wireless connectivity(Optional) 802.11 b/g, a/b/g WLAN with bulit-in antennas

interface(Optional)

ISO 3 tracks MSR module (side mounting)

Internal USB connection (option) Smart card reader dual

Mifare passive RFID reader below 5cm distance

Application

Access to patient records / Hospital administration system / Bed management

Manufactory information:

Factory：Flytech Technology Co., Ltd.
Address：No. 34, Wu-Cyuan 3rd Road, Wu-Gu Township, Taipei Hsien, Taiwan
Tel No：886-2-2298-2696
Fax No：886-2-2298-2786
Note: Cleaning solution-Wipe with cloth using clean water, 2 times a week.

25

6 Jumper Settings

6-1 B78 motherboard

6-1-1 Motherboard Layout

JP13

JP7

JP14

JP6

JP3

JP9

JP10

JP8

JP4

26

6-1-2 Connectors & Functions

Connector Function

BAT1 CMOS Battery Base ( Use CR2023)
CN1 Audio Line Out
CN2 Audio MIC In
CN3 Internal Power Switch
CN4 Speaker & MIC Connector
CN9 CD-IN Connector
CN11 Power Connector For 3.5" HDD
CN13 COM5 for Touch
CN15 CPU FAN Connector
CN16 Hardware Reset
CN18 USB2
CN19 LCD Interface Connector
CN20 Inverter Connector
CN21 Card Reader Connector
CN22 System FAN Connect or
CN23 IrDA Connector
CN24 FT Status Interface
CN26 Internal Power In Connector
CN27 Internal LPT Connector
CN28 Internal PCI Reset Output Connector
IED1 Secondary IDE Connector (Pitch = 2.0mm)
PRN1 Parallel Port
PWR1 +19V Power Adaptor
RJ11_1 Cash Drawer Connector
RJ45_1 LAN (On Board)
RJ45_2 COM1, COM2, COM3, COM4
SATA1 SATA Connector
USB1 USB3, USB4
USB2 USB5, USB6
JP1 VGA Port
JP2 VGA Power

27

6-1-3 Jumper Setting

LCD ID Setting

LVDS

JP7

Panel # Resolution

Bits Channel

1 1366 x 768 24 Single

(1-2) (3-4) (5-6) (7-8)

1 3 5 7

2 4 6 8

Power Mode Setting

Function JP6 (1-2)

ATX Power

◎AT Power

CMOS Operation Mode

Function JP8 (1-2)

◎CMOS Normal

CMOS Reset

28

USB Path Setting (do not change)

Function JP14 (1-2)

To Docking

◎To Motherboard

System Indicator Function (do not change)

JP13

Function

(1-2) (3-4) (5-6) (7-8)

1 3 5 7

◎Disable

Enable

2 4 6 8
1 3 5 7

2 4 6 8

◎ = Default

Note:

OPEN SHORT

29

6-2 B68 Motherboard

6-2-1 Motherboard Layout

30

6-2-2 Connectors & Functions

Connector Function

BAT1 CMOS Battery Base ( Use CR2023)
CN1 Power On Button
CN2 Touch Sensor
CN3 Power LED
CN4 SATA1 HDD Power Connector
CN5 SATA2 HDD Power Connector
CN6 LCD Interface Connector
CN7 IrDA Connector
CN8 For External Touch Connector
CN9 Inverter Connector
CN10 Card Reader Connector
CN11 Line Out
CN12 LED Power
CN13 MIC In
CN14 Speaker & MIC CONN
CN15 CD-IN CONN
CN17 LAN LED
CN18 USB5
CN19 DC-JACK
CN20 PS2 KEYBOARD
CN21 For Beside Terminal
CN22 LPT Interface for Touch
CN23 For LPT Touch Reset
DDR2_A1 DDR2 SO-DIMM1
DDR2_A2 DDR2 SO-DIMM2
PRN1 Parallel Port
PWR1 +19V Power Adaptor
RJ11_1 Cash Drawer Connector
RJ45_1 COM1, COM2, COM3, COM4
SATA1 SATA Connector
SATA2 SATA Connector
USB1 USB1, USB2
USB2 USB3, USB4
SW1 Power On Bottom
JP1 CRT Connector
JP2 CRT Power/I2C Connector

31

JP7 LCD ID Setting
JP8 RTC Reset
JP9 AT Function
JP12 Hardware Reset

32

6-2-3 Jumper Setting

Power Mode Setting

Function JP9 (1-2)

ATX Power

◎AT Power

CMOS Operation Mode

Function JP8 (1-2)

◎CMOS Normal

CMOS Reset

LCD ID Setting

LVDS

Panel # Resolution

Bits Channel

◎1

2 1440 x 900 24 Dual

4 1920 x 1080 24 Dual

1366 x 768 24 Single

Output

Interface

LVDS

Panel

LVDS

Panel

LVDS

Panel

JP7

(1-2) (3-4)
(5-6) (7-8)

33

Panel # Resolution

LVDS

Bits Channel

Output

JP7

(1-2) (3-4)

Interface

(5-6) (7-8)

5 1024 x 768 24 Single

6 1280 x 1024 24 Dual

7 800 x 600 24 Single

9 1024 x 768 18 Single

LVDS

Panel

LVDS

Panel

LVDS

Panel

LVDS

Panel

11 800 x 600 18 Single

12 800 x 600 18 Single

CRT

Remark:

Panel ID#12 is specialized for Sharp 12.1” LQ121S1LG41/
LQ121S1LG42 panel.
Note:

LVDS

Panel

LVDS

Panel

34

OPEN SHORT

7 BIOS Settings

7-1 BIOS Setup Utility

The BIOS setup defines how the system is configured. You need to run this
program the first time you configure this product. You may need to run it again if
you change the configuration.
You need to connect a PC keyboard to the keyboard connector to run the BIOS
setup utility.

7-2 Starting the BIOS Setup

Turn on or reboot this product.

Press the DEL key immediately after the product is turned on, or press the DEL

key when the following message is displayed during POST (the Power on

Self-Test)

Press DEL to enter SETUP.

The main menu of the BIOS setup is displayed.
If the supervisor password is set, you must enter it here.

7-3 When a Problem Occurs

If, after making and saving system changes with the Setup utility, you find that
this product no longer boots, start the BIOS setup and execute the following

Load Optimized Defaults

7-4 BIOS Main Menu

When the BIOS Main Menu is displayed, the following items can be selected.
Use the arrow keys to select items and the Enter key to accept and enter the
sub-menu.

35

Note: The BIOS setup menus shown in this section are for reference only and
may not exactly match the items of your BIOS version.
.

Standard CMOS Features

Use this menu for basic system configuration.

Advanced BIOS Features

Use this menu to set the Advanced Features available on the system.

Advanced Chipset Features

Use this menu to change the values in the chipset registers and optimize the
system’s performance.

Integrated Peripherals

Use this menu to specify your settings for integrated peripherals.

Power Management setup

Use this menu to specify your settings for power management.

PnP/PCI Configurations

This entry appears if your system supports Plug and Play and PCI

36

Configuration.

PC health status

Displays CPU, System Temperature, Fan Speed, and System Voltages Value.

Load Optimized Defaults

Use this menu to load the BIOS default values, i.e., factory settings for optimal
performance system operations. While A ward has designed the custom BIOS to
maximize performance, the factory has the option to change these defaults to
meet their needs.

Set Supervisor Password

Enables you to change, set, or disable the supervisor or user password.

Set Password

Change, set, or disable the password. It allows you to limit access to the system
and to the setup, or just to the setup.

Save & exit setup

Save CMOS value changes to CMOS and exits setup.

Exit without saving

Ignores all CMOS value changes and exits setup.

37