Page 1
KPC2 KPC3 KPC4
with B42 M/B
Installation Guide
48201070
Dec 2004 V1.0
Page 2
Safety
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions carefully. Save these instructions for future reference.
2. Follow all warnings and instructions marked on the product.
3. Do not use this product near water.
4. Do not place this product on an unstable cart, stand, or table. The product may fall,
causing serious damage to the product.
5. Slots and openings in the cabinet and the back or bottom are provided for ventilation; to
ensure reliable operation of the product and to protect it from overheating, these openings
must not be blocked or covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This product should never be placed
near or over a radiator or heat register, or in a built-in installation unless proper ventilation
is provided.
6. This product should be operated from the type of power indicated on the marking label. If
you are not sure of the type of power available, consult your dealer or local power
company.
7. Do not allow anything to rest on the power cord. Do not locate this product where
persons will walk on the cord.
8. Never push objects of any kind into this product through cabinet slots as they may touch
dangerous voltage points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
FCC
This device complies with part 15 of the FCC rules. Operation is subject to the following two
condition: (1)This device may not cause harmful interference and (2) This device must accept
any interference received, including interference that may cause undesired operation.
CD-ROM Safety Warning
DANGER
INVISIBLE RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM
Caution on Lithium Batteries
Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer. Discard used batteries according to the
manufacturer’s instructions.
/ 19 2
Page 3
Index
1. Accessory....................................................................................................... 4
2. I/O Function.................................................................................................... 6
2.1 KPC2 Front View..................................................................................... 6
2.2 KPC2 Rear View...................................................................................... 6
2.3 KPC3 Front View..................................................................................... 7
2.4 KPC3 Rear View...................................................................................... 7
2.5 KPC4 Front View..................................................................................... 8
2.6 KPC4 Rear View...................................................................................... 8
3. Specification................................................................................................... 9
3.1 B42 .......................................................................................................... 9
3.2 System Memory Combination................................................................ 10
4. Jumper Setting............................................................................................. 11
4.1 B42 M/B..................................................................................................11
4.1.1 CMOS Clear Selection................................................................ 12
4.1.2 Power Mode Selection................................................................ 12
4.1.3 COM2 RS232/485/422 Selection................................................ 12
5. Driver Installation.......................................................................................... 13
5.1 B42 M/B................................................................................................. 13
5.1.1 Chipset Driver Installation........................................................... 13
5.1.2 VGA Driver installation................................................................ 15
5.1.3 LAN Driver Installation ................................................................ 16
5.1.4 Audio Driver Installation.............................................................. 17
5.1.5 USB 2.0 Driver Installation.......................................................... 18
6. Notices ......................................................................................................... 19
6.1 Maximum dimension of PCI Add-on card............................................... 19
/ 19 3
Page 4
1. Accessory
a. Warranty Card b. Power Cord
c. Wall mount bracket d. Adapter
e. Drivers Bank f. System robber pads
g. Y Cable (Keyboard & Mouse, only for
KPC4)
h. Installation Guide
/ 19 4
Page 5
i. Screw (38000161)
The following drivers in the folders of Driver Bank are necessary for driver installation.
B42 Mainboard
Folder/File File Description
<CD>:\B42\B42.htm B42 Driver list
<CD>:\Common\VIA\Chipset
Chipset driver
<CD>:\Common\VIA\VGA\CLE266 VGA driver
<CD>:\Common\LAN_driver\R8139_810x LAN driver
<CD>:\Common\Ac97_codec\Realtek\ALC202A Audio driver
<CD>:\Common\VIA\USB2.0 USB2.0 driver
/ 19 5
Page 6
2. I/O Function
2.1 KPC2 Front View
2.2 KPC2 Rear View
5
1
2 3
4
15
8
6 7
# Function # Function
1 Power Button 9 USB 1& 2
2 Line In 10 VGA
3 Line out 11 LPT
4 USB 3 & 4 12 COM2
5 Slim CD-ROM 13 COM1
9
10 11 12 13
16
14
6 19V DC Jack 14 LAN
7 PS/2 Keyboard 15 PCI slot 1
8 PS/2 Mouse 16 PCI slot 2
/ 19 6
Page 7
2.3 KPC3 Front View
5
1
2 3
2.4 KPC3 Rear View
8
6 7
# Function # Function
1 Power Button 9 USB 1& 2
9
21 15
10 11 12
4
13 14
2 Line In 10 VGA
3 Line out 11 LPT
4 USB 3 & 4 12 COM2
5 Slim CD-ROM 13 COM1
6 19V DC Jack 14 LAN
7 PS/2 Keyboard 15 PCI slot
8 PS/2 Mouse
/ 19 7
Page 8
2.5 KPC4 Front View
1
2 3
4
2.6 KPC4 Rear View
5
# Function # Function
1 Power Button 7 USB 1& 2
2 Line In 8 VGA
3 Line out 9 LPT
6 7
8 10 11 12
9
4 USB 3 & 4 10 COM2
5 19V DC Jack 11 COM1
6 PS/2 Keyboard/Mouse
(Using Y cable)
12 LAN
/ 19 8
Page 9
V
T
3. Specification
3.1 B42
Model
M/B
Core Logic
CPU
System Memory
BIOS
ideo Display
Video Memory
I/O Controller
LAN controller
KPC2 KPC3 KPC4
B42
VIA CLE266 (VT8623CE) North Bridge
VIA VT8235CD South Bridge
VIA Eden / C3 EBGA Processors
133/100/66MHZ CPU Front Side BUS (FSB)
C3 EBGA 733 / 800 / 1.0G / 1.2G or High (Optional)
C3 EBGA 733 Standard to Use
1 x DDR266/200 SO-DIMM up to 1G byte memory size
Award PnP BIOS
Integrated ProSavage8 2D/3D Video Accelerator
MPEG-2 video textures
2D/3D resolutions up to 1920 x 1440
16/32/64 MB frame buffer using system memory
Winbond 83697HFx1
Realtek RT8100BL 10/100Mb fast Ethernet controller
V – Out (Option)
HDD connector
USB Controller
Audio controller
Expansion Slot
M/B dimension
Power Input
Support Wake-On-LAN and boot from LAN
PAL / NTSC multi system support
VIA VT1622A TV Out (TV Encoder)
1 x 10 pin-header support RCA interface
Primary: 1x 40-pin 2.54 pitch (IDE1 connector) or
1x 44pin 2.0 pitch (IDE2 connector) either one
Secondary: 1x 44pin 2.0 pitch (IDE3 connector)
IDE connector location please refer chap 4.1
VT8235 Integrated support USB2.0
AC’97 Realtek ALC202A (2ch)
2 x PCI slot 1 x PCI slot N/A
207 mm (W) x 230 mm (D)
AC Adapter(FT809010)
Input requirement:
AC 90Vac ~ 264Vac / 47Hz ~ 63Hz single phase
Output requirement: DC input 19V/90W
EMC
Safety
CE Class B
FCC Class B
LVD,EN60950
/ 19 9
Page 10
I/O port
Rear Panel (KPC2,KPC3):
1 x 19V DC jack
1 x PS/2 Keyboard
1 x PS/2 Mouse
2 x USB 2.0 ports
1 x DB-15F VGA port
1 x DB-25F Parallel port
2 x DB-9M RS-232 Serial port
1 x RJ-45 LAN port
Rear Panel (KPC4):
1 x 19V DC jack
1 x PS/2 Keyboard & Mouse (Using Y cable)
2 x USB 2.0 ports
1 x DB-15F VGA port
1 x DB-25F Parallel port
2 x DB-9M RS-232 Serial port
1 x RJ-45 LAN port
Front Panel:
2 x USB 2.0 ports
2 x Audio jacks: line-out, line-in
Temperature
OS Support
Operation :5°C to 35°C (41°F to 95 °F)
Storage :0°C to 40 °C (32°F to 104 °F)
Windows 9x/ME/NT 4.0/2000/XP
Windows CE 4.X
Linux
3.2 System Memory Combination
3.2.1 KPC2/KPC3/KPC4 B42 M/B
RAM Size
Slot
DIMM1 128 MB 256 MB 512 MB 1024 MB
128MB 256MB 512MB 1024MB
/ 19 10
Page 11
4. Jumper Setting
4.1 B42 M/B
/ 19 11
Page 12
4.1.1 CMOS Clear Selection
* Default Setting
Function JP1 (SHORT)
* Normal
Clear 2-3
1-2
4.1.2 Power Mode Selection
Function JP4 (SHORT)
* ATX
AT 1-2
2-3
4.1.3 COM2 RS232/485/422 Selection
Function JP5 (SHORT) JP6 (SHORT)
* RS232
RS485 4-6
RS422
1-2
3-4
5-7
7-8
1-2
3-4
5-6
Note:
OPEN
9-10
7-8
9-10
11-12
SHORT
/ 19 12
Page 13
5. Driver Installation
5.1 B42 M/B
The following procedures are for Windows XP, other platforms are similar.
5.1.1 Chipset Driver Installation
Driver path: <CD>:\Common\VIA\Chipset)
a. Click “VIAHyperion4in1453v.exe” on the
My computer window.
b. Click “Next” button on the Welcome
window.
c. Click “Yes” button on the ReadME
window.
d. Click “Next” button on the 4in1 Setup
Mode Option window.
/ 19 13
Page 14
e. Click “Next” button on the Setup
Component window.
f. Click “Next” button on the VIA PCI IDE
Bus Driver window.
g. Click “Next” button on the VIA_GART
h. Click “OK” button to restart the system.
AGP Driver window.
/ 19 14
Page 15
5.1.2 VGA Driver installation
Driver path: <CD>:\Common\VIA\VGA\CLE266)
a. Click “Setup.exe” on the My computer
window.
b. Click “Next” button on the Welcome
window.
c. Click “Next” button on the Start Copying
Files window.
d. Click “Continue Anyway” button on the
Hardware Installation window.
e. Click “Finish” button to restart the system.
/ 19 15
Page 16
5.1.3 LAN Driver Installation
Driver path: <CD>:\Common\LAN_driver\R8139_810x)
a. Click “Setup.exe” on the My computer
window.
b. Click “Next” button on the LanSetup
window.
c. Click “Finish” button on the LanSetup
window..
/ 19 16
Page 17
5.1.4 Audio Driver Installation
Driver path: <CD>:\Common\Ac97_codec\Realtek\ALC202A)
a. Click “wdm_a3631.exe” on the My
computer window .
b. Click “Next” button on the Welcome
window.
c. Click “Continue Anyway” button on the
d. Click ”Finish” button to restart system.
Hardware Installation window.
/ 19 17
Page 18
5.1.5 USB 2.0 Driver Installation
Driver path: <CD>:\Common\VIA\USB2.0)
a. Click “Setup.exe” on the My computer
window.
b. Click “Next” button on the Welcome
window.
c. Click “Next” button on the Setup
d. Click ”Yes” button to restart system.
Component window.
/ 19 18
Page 19
6. Notices
6.1 Maximum dimension of PCI Add-on card
(Maximum dimension of Interface card: 125.5 mm x 81 mm)
125.5 mm
81mm
/ 19 19
Loading...