Version 1.0 February, 2015
K738/K746/747
Panel PC
Hardware System
User Manual
i
Copyright 2015
All Rights Reserved
Manual Version 1.0
The information contained in this document is subject to change without notice.
We make no warranty of any kind with regard to this material, including, but not
limited to, the implied warranties of merchantability and fitness for a particular
purpose. We shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of
this material.
This document contains proprietary information that is protected by copyright. All
rights are reserved. No part of this document may be photocopied, reproduced or
translated to another language without the prior written consent of the
manufacturer.
TRADEMARK
Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation.
Other trademarks mentioned herein are the property of their respective owners.
ii
Safety
IMPORTANT SAFETY INSTRUCTIONS
1. To disconnect the machine from the electrical Power Supply, turn off the power
switch and remove the power cord plug from the wall socket. The wall socket
must be easily accessible and in close proximity to the machine.
2. Read these instructions carefully. Save these instructions for future reference.
3. Follow all warnings and instructions marked on the product.
4. Do not place this product on an unstable cart, stand, or table. The product may
fall, causing serious damage to the product.
5. This product should be operated from the type of power indicated on the marking
label. If you are not sure of the type of power available, consult your dealer or
local power company.
6. Do not allow anything to rest on the power cord. Do not locate this product where
persons will walk on the cord.
CE MARK
This device complies with the requirements of the EEC directive 2004/108/EC
with regard to “Electromagnetic compatibility” and 2006/95/EC “Low Voltage
Directive”
FCC
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that
may cause undesired operation
CAUTION ON LITHIUM BATTERIES
There is a danger of explosion if the battery is replaced incorrectly. Replace only with
the same or equivalent type recommended by the manufacturer. Discard used
batteries according to the manufacturer’s instructions.
Battery Caution
Risk of explosion if battery is replaced by an incorrectly type.
Dispose of used battery according to the local disposal instructions.
Safety Caution
Note: To comply with IEC60950-1 Clause 2.5 (limited power sources, L.P.S) related
legislation, peripherals shall be 4.7.3.2 "Materials for fire enclosure" compliant.
4.7.3.2 Materials for fire enclosures
For MOVABLE EQUIPMENT having a total mass not exceeding
18kg.the material of a FIRE ENCLOSURE, in the thinnest significant
wall thickness used, shall be of V-1 CLASS MATERIAL or shall pass
the test of Clause A.2.
For MOVABLE EQUIPMENT having a total mass exceeding 18kg
iii
and for all STATIONARY EQUIPMENT, the material of a FIRE
ENCLOSURE, in the thinnest significant wall thickness used, shall
be of 5VB CLASS MATERIAL or shall pass the test of Clause A.1
LEGISLATION AND WEEE SYMBOL
2012/19/EU Waste Electrical and Electronic Equipment Directive on the treatment,
collection, recycling and disposal of electric and electronic devices and their
components.
The crossed dustbin symbol on the device means that it should not be disposed of
with other household wastes at the end of its working life. Instead, the device
should be taken to the waste collection centers for activation of the treatment,
collection, recycling and disposal procedure.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can take
this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of
the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
iv
Revision History
Revision Date Description
V1.0 February, 2015 Release
v
Table of Content
1 Item Checklist ......................................................... 1
1-1 Standard Items ............................................................................... 1
2 Specification ........................................................... 2
3 System View ............................................................ 4
3-1 Front View & Side View .................................................................. 4
3-2 Rear View & Side View ................................................................... 5
3-3 Top View .......................................................................................... 5
3-4 Dimension ....................................................................................... 6
3-5 I/O View ........................................................................................... 9
3-6 Connector PIN Definition ............................................................. 10
4 Install the Panel Mount ...................................... 11
5 Configuration ....................................................... 13
Appendix: Driver Installation ................................. 14
1
1 Item Checklist
1-1 Standard Items
a. System x 1 b. Power connector x 1
c. RS-232 connector x 2 d. GPIO/RS-232/422/485 connector x2
e. Ground cable x 1 f. Mounting bracket kit x 10
g. Key x 2 h. Rubber strip x 1
i. Driver CD x1 j. Cable tie x 2
2
2 Specification
Model K738 K746 K747
Motherboard D35
Processor Celeron J1900 2.0GHz L2 2M (10W)
Core Logic Built-in SoC
System Memory
1 x DDR3L SO-DIMM slot, FSB 1066/1333MHz
Default 4GB RAM (Max 8GB)
Graphic Memory Intel Graphic DX11.1
LAN1 Controller Intel WG I211AT
LAN2 Controller Intel WG I211AT
Audio Controller Realtek ALC662VDO-GR
I/O Controller Winbond NCT6106D
LVDS Controller Realtek RTN2136R
BIOS Phoenix UEFI
Touch Controller ETTI (USB)
TPM Contoller NUVOTON TPM NPCT420
Watch Dog Timer Hardware WDT
MB Dimension 185 x 120 mm
IO Board Dimension 248 x 64 mm
Expansion
Mini PCIe 1 x miniPCIe half size
LCD Touch Display
LCD Display 18.5" LED Panel (16:9)
12.1" LED Panel (4:3) 15" LED Panel (4:3)
Resolution 1366 x 768 1024 x 768 1024 x 768
Brightness 250 nits 500 nits 450 nits
Touch
True Flat Resistive
True Flat P-CAP
True Flat Resistive
True Flat P-CAP
True Flat P-CAP
Storage
m-SATA 32GB PCIe full length slot for mSATA only
HDD 7-pin SATA connector
Power
Power Input 12-48Vdc (Polarity Reverse Protection)
Front I/O
USB 2.0 1
Power Button 1
3
NFC 1(option)
RFID 1(option)
Rear I/O
Power Switch 1
Power in "+" , "GND" , "Chassis GND" (3 pin pitch 5mm Terminal Block)
VGA 1
DVI-D 1
RS-232 2 (8x2 pitch 3.81mmTerminal Block w/ screw)
GPIO
9(8+1GND) (9x2 pitch 3.81mm Terminal Block w/ screw)
4ch Digital input ; 4ch Digital output
RS-232/422/485 9(8+1NC) (9x2 pitch 3.81mm Terminal Block w/ screw)
LAN 2 x Gigabit Ethernet (RJ-45)
USB2.0 4 (type A)
Audio Mic-in / Line-out
I/O Board Internal
Mini PCI-E 2 (1 x Full-size, 1 x Half-size)
m-SATA 1
I/O Board Component
Isolation 2kV
RS-232 x 2
1 x RS-232/422/485 (8 pins)
GPIO (4ch Digital input ; 4ch Digital output )
Surge 3kV 2 x LAN
Polarity Reverse Protection Power in
Environmental
Operating Temperature 0 oC ~ 50 oC (32 oF ~ 122 oF) (Still Air)
Operating Humidity 10 ~ 95%@40°C (non-condensing)
Operating Vibration 1Grms, 5 ~ 500Hz
Operating Shock 20G
Waterproof Front IPX6/Rear IP20
Certificate / Safety
Certificate FCC Class B, CE, LVD
ESD
Criteria B: 4KV/8KV
Criteria C: 8KV/15KV
Weight 6.5kg 4.8kg 5.8 kg
OS Support
WES7 Pro 32&64 bit / Windows 7 Pro 32&64 bit / WES8 Pro 32&64 bit /
Windows 8 Pro 32 & 64 bit / Linux
Option Kits
NFC (interface i2C) Windows 8.1 only
Wi-Fi 802.11b/g/n RFID
* This specification is subject to change without prior notice.
4
3 System View
3-1 Front View & Side View
No. Description
1 Touch screen
2 WIFI/RFID/NFC Antenna (option)
3 Key lock
4 USB 2.0
5 Power switch
5
3-2 Rear View & Side View
No. Description
6 Cable clamp
7 Groove for mounting clip
3-3 Top View
No. Description
8 WIFI antenna (option)
6
3-4 Dimensions
K746 (12.1’)
300mm (cut-out dimension)
280mm
(
cut-out dimension
)
7
K747 (15’)
375mm (cut-out dimension)
333mm
(
cut-out dimension
)
8
K738 (18.5’)
474mm (cut-out dimension)
336mm
(
cut-out dimension
)
9
3-5 I/O View
Number Description
a Power switch
b Power input
c VGA
d DVI-D
e COM6 (RS-232/422/485)
f 4 x DI, 4 x DO
g COM1 (RS-232)
h COM2 (RS-232)
i LAN
j USB
k Line-out
l Mic-in
10
3-6 Connector PIN Definition
RS-232/422/485 mode changed by BIOS setting
RS-232 Pin Define
1 DCD
2 DSR
3 RxD
4 RTS
5 TxD
6 CTS
7 DTR
8 GND
RS-232/422/485 Pin Define
RS-232 RS-422 RS-485
1 DCD TX- DATA-
2 DSR
3 RxD TX+ DATA+
4 RTS
5 TxD RX+
6 CTS
7 DTR RX-
8 GND
11
4 Install the Panel Mount
Mounting method that mounts product into an opening of mounting wall from the front
and secured from the rear. The installation steps are as follow:
1. Assemble the mounting bracket kits.
2. Put the rubber strip on the rear side of the panel mount product as shown
in the picture above.
.
12
3. Put the panel mount product in the cut-out (dimension: 375mm x 333mm) from the front
side of mounting wall, with the sides of the front bezel shown on the outside.
4. Use provided mounting bracket kits (x10) to attach and tighten the panel mount product to
the mounting wall as picture shown above.
* Screw Torque Value: 8kg-cm
13
5 Configuration
RS-232/422/485 Setting
1. Power on the system, and press
the <DEL> key when the system is
booting up to enter the BIOS Setup
utility.
2. Select the Advanced tab.
3. Select VGA/COM Power
Configuration Ports and press
<Enter> to go to display the
available options.
4. To enable the power, select RS232
Power setting and press <Enter>.
Select Power and press <Enter>.
Save the change by pressing F10.
14
Appendix: Driver Installation
The shipping package includes a Driver CD. You can find every individual driver and
utility that enables you to install the drivers in the Driver CD.
Please insert the Driver CD into the drive and double click on the “index.htm” to
pick the models. You can refer to the drivers installation guide for each driver in the
“Driver/Manual List”.
Loading...