Page 1
.
USER’S MANUAL
B63 MAIN BOARD
482B6302
Page 2
Printed in Taiwan 2000
- -
.
Page 3
.
INDEX
This user’s manual describes the jumper setting of B63 Main Board. For
detailed technical information, please refer to CDs attached with PC system
unit.
Table of Contents Page
Technical details
1. Jumpers location diagram for B63 main board 1
2. Memory configuration 2
3. Jumper setting 3-7
All other registered and unregistered trademarks are trademarks of their respective
holders
Page 4
1. Jumpers Location Diagram for "B63 V1.X " main board
1
Page 5
2.Memory configuration for “B63 V1.X” main board
Capacity DIMM 1 DIMM 2
16MB
16MB
32MB
32MB
32MB
80MB
80MB
64MB
64MB
128MB
128MB
128MB
256MB
16MB none
none 16MB
16MB 16MB
32MB none
none 32MB
16MB 64MB
64MB 16MB
64MB none
none 64MB
64MB 64MB
128MB None
None 128MB
128MB 128MB
l VGA Memory Configuration.
Capacity U24 U25 Video DRAM Type
4MB
close close 512KB X 32 SOP package
2
Page 6
3. Jumper Setting
=CPU type selection :
CPU
Intel Celeron 300MHz 4.5x 66MHz Open Close Open Close Close
Intel Celeron 333MHz 5.0x 66MHz Open Open Close Close Close
Intel Celeron 366MHz 5.5x 66MHz Open Open Open Close Close
Intel Celeron 400Mhz 6.0x 66MHz Close Close Close Open Close
Intel Celeron 433Mhz 6.5x 66MHz Close Close Open Open Close
Intel Celeron 466MHz 7.0x 66MHz Close Open Close Open Close
Intel Celeron 500Mhz 7.5x 66MHz Close Open Open Open Close
(Remark: All Intel CPU will defect jumper setting automatically)
=M-System Disk On Chip: JP20, JP19
Freq. Ratio Externa
l
Clock
JP21
1-2
JP21
3-4
JP21
5-6
JP20 JP19 USER ADDRESS
1-2 1-2 0C800-0C9FF (Default)
1-2 3-4
3-4 1-2
3-4 3-4
5-6 1-2
6-5 3-4
0CC00-0CDFF
0D000-0D1FF
0D400-0D5FF
0D800-0D9FF
0DC00-0DDFF
JP21
7-8
JP21
9-10
=
CMOS Operation mode: J12
Function
CMOS Normal
CMOS Reset
=
ATX / AT power mode: JP18, J3
Function
4000 Series
2-3 (Default)
J12
1-2
JP18 J3
Close
1-2
4001 FT-8050 AT Internal power supply
(default)
3
Page 7
1000 Series
FT-8075 AT Internal Power Supply
ATX power supply Open
=COM Port Jumper Setting
Close
1-2
2-3
COM1
JP1
COM2
JP2
COM3
JP7
COM4
JP6
JP4
(Default)
JP3 1-2 Data Line
JP9 1-2 Data Line
JP5 1-2 Data Line
1-2 Data Line
3-4 +5V
5-6 +12V
3-4 +5V
5-6 +12V
3-4 +5V
5-6 +12V
3-4 +5V
5-6 +12V
4
Page 8
=
Fan Connector : J13, J14 (default to use +12V Power )
Pin Assignment J13, J14
1 +12V
2 Ground
3 VCC
Figure
=COMPACT FLASH POWER : JP29
(default to use +5V Power)
Pin Assignment JP29
Pin 1 +5V
Pin 2 Ground
=
Power Push Button: JP12
5
Page 9
=
GND
OUT3
OUT1
OUT2
OUT0
VDC+12V
Digital I/O (4 Output & 4 Input) : J11
This main board provide the basic digital I/O signal
controller, user can develop the program and extra
controller to open and sense of the cash drawer based on the
digital I/O function on this main board.
PIN ASSIGNMENT
1 GND 6 Out 1
2 VDC +12V 7 IN 2
3 IN 0 8 Out 2
4 Out 0 9 IN 3
5 IN 1 10 Out 3
IN3 IN2
9
IN1
IN0
3
5
7
1
8
10
6
2
4
ν Digital output programming
The output is TTL Level. The output signal must be TTL
compatible.
Output Address Bit
Out 0 206 0
Out 1 206 1
Out 2 206 2
6
Page 10
Out 3 206 3
Example : ( “0” = off “1” =on )
Data 00 = Out 0 and Out 1 = “0”
Data 01 = Out 0 = “1”
Data 02 = Out 1 = “1”
Data 03 = Out 0 and Out 1 = “1”
ν Digital input programming
The input signal must be TTL compatible.
Input Address Bit
IN 0 206 0
IN 1 206 1
IN 2 206 2
IN 3 206 3
Example : If input 206 is [ 0111], then input 3 is “0”
If input 206 is [0011], then input 3 & 4
are “0”
7
Loading...