POS310/312
with B46 M/B
Installation Guide
POS 310(Black/White) POS312(Black/White)
Point-of-Sale
Hardware System
Part no. 48200301
July. 2004 (V2.0)
Safety
IMPORTANT SAFETY INSTRUCTIONS
● Read these instructions carefully. Keep these instructions for future reference.
● Follow all warnings and instructions marked on the product.
● Do not use this product near water.
● Do not place this product on an unstable cart, stand, or table. The product may
fall, causing serious damage to the product.
● Slots and openings in the cabinet and the back or bottom are provided for
ventilation; to ensure reliable operation of the product and to protect it from
overheating, these openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed, sofa, rug, or other
similar surface.This product should never be placed near or over a radiator or
heat register, or in a built-in installation unless proper ventilation is provided.
● This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult your
dealer or local power company.
● Do not allow anything to rest on the power cord. Do not locate this product
where persons will walk on the cord.
● Never push objects of any kind into this product through cabinet slots as they
may touch dangerous voltage points or short out parts that could result in a fire
or electric shock. Never spill liquid of any kind on the product.
FCC
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may
cause undesired operation.
Caution on Lithium Batteries
Danger will explosion if battery is incorrectly replaced. Replace only with the same
or equivalent type recommended by the manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
/ 27
2
Index
1.Accessory
4
2.I/O Function..................................................................................... 5
3. Specification
6
4.Install External Device 7
4.1 Install Programmable Keypad ...................................................... 7
4.2 Install Cash Drawer ......................................................................9
5. Disassemble Procedures
13
6. Jumper Setting 17
6.1 Main Board Jumper Setting........................................................ 17
6.2 Connector Board Jumper Setting ...............................................19
7. Driver Installation
21
7.1 Chipset Driver Installation ..........................................................21
7.2 LAN Driver Installation................................................................ 23
7.3 Audio Driver Installation.............................................................. 24
7.4 Touch.......................................................................................... 25
8.Install touch driver on DOS mode
26
/ 27
3
1.Accessory
AC Adapter Power Cord
Driver Bank Warranty Card
Folder/File File Description
<CD>:\B46\B46.htm B46 Driver list
<CD>:\B46\VIA4IN1 Chipset driver
<CD>:\B46\Audio\V4.50b Audio driver
<CD>:\Common\LAN_drive\ R8139_810x LAN driver
<CD>:\Common\MION_Touch Touch driver
/ 27
4
2.I/O Function
(Note: POS312 without I-button function)
2.1 Front View 2.2 Bottom View
I-button
Brightness Up & Down
Power indicator
Power Button
2.3 I/O Ports
2
1
3
.
# Function # Function # Function # Function
5 8
4
6
7
9
10
11
12
1 DC 19V IN 4 LPT 7 COM4 10 DIO1
2 PS/2 Mouse 5 COM1 8 COM3 11 LAN
3 PS/2 Keyboard 6 COM2 9 DIO2 12 USB 1 & 2
2.4 Side View
Another PS/2 keyboard port
PS/2
Keyboard
/ 27
5
3. Specification
V
V
4
W
A
Item Description
Main Board B46
CPU
Core Logic
POS310 10" DSTN-LCD Anti-glare LCD size
POS312 10.4” TFT LCD
POS310 70~100cd/m2 Brightness
POS312 150 cd/m2
Display Function (built-in) on NS-CS5530
Compact Flash (Secondary/IDE)Type 1, Socket supported
HDD (Primary/IDE)Internal Slim type 44pin header (optional)
RAM On-board 128MB, 1 x S.O.-DIMM up to 256MB
Resolution 800 x 600
Touch Screen
Touch Panel Miontec 4 Wire (COM5)
Serial Port 6, Pin 1/9 with +5V/+12V, COM4 for Card Reader,
Cash Drawer 2(with 12V/24V Output, MAX 24V≤2A)
IA Eden ESP4K/6K/7K
IA VT8606 + VT686B
Wire Resistive type (Miontec )
COM5 for Touch Screen, COM6 for Customer Display
LPT 1
USB 2(V1.1)
PS2 Keyboard x 1, Mouse x 1
LAN 1, (10/100 Base-T), RTL-8100 Chipset
Audio Line Out, System Speaker support (LCD Function Board)
Magnetic Card Reader 3 Tracks, Keyboard or RS232 type (COM4) (Optional)
Customer Display LED type, (COM6) (Optional)
Programmable Keypad 32 keys with key lock, Smart IC Card Reader (Optional)
Dallars Key i-Button Key Reader (Keyboard type, Optional)
Expansion Slot Mini PCI Socket
OS support
Power Supply
Spill-proof Touch Screen Panel
M/B Dimensions 200mm(W) x 185mm(D) x 25mm(H)
Temperature 5°C~ 35°C, operating
indows CE/ 98/ 2000/ XP, Linux
C Adapter: Input 100 ~ 240V, Output 19V/90W
Safety: UL, CUL. TUV, CB, CSA
EMI FCC/CE Class B, VCCI
/ 27
6
4.Install External Device
4.1 Install Programmable Keypad
a. Turn over the system before installing the
keypad.
c. Turn over the keypad and loosen the back
cover four screws.
b. Loosen the two screws at the side of the
system and remove the keypad cover.
d. Take off the back cover.
e. Attach the keypad to the side of the
system.
/ 27
7
f. Tighten the two screws so the keypad can
be fully connected to the system.
g. Recover the back cover of the keypad. h. Attach the keypad to the side of the
system and tighten the four screws
around the back cover.
I. Now the keypad is fully installed.
/ 27
8
4.2 Install Cash Drawer
You can install a cash drawer through the
cash drawer port. Please confirm the pin
assignment before installation.
4.2.1 Cash Drawer Pin Assignment
Pin Signal Pin Signal
1 GND 7 GND
2 DOUT bit0 8 DOUT bit2
3 DIN bit0 9 DIN bit2
4 12V/24V 10 12V/24V
5 DOUT bit1 11 DOUT bit3
6 GND 12 GND
6 1
/ 27
9
7
12
1
4.2.2Cash Drawer Controller register description
The Cash Drawer Controller use two I/O addresses to control Cash Drawer –Cash
Drawer Control Register and Cash Drawer Status Register.
4.2.2.1Cash Drawer Control Register
Register Location: I/O port 206h
Attribute: Write
Size: 8bit
7 6 5 4 3 2 1 0
X X X X X X
Cash Drawer1 “DOUT bit0” pin output control
Reserved
Cash Drawer2 “DOUT bit2” pin output control
Reserved
Bit 7-3: Reserved
Bit 2: Cash Drawer2 “DOUT bit2” pin output control.
= 1: Opening the Cash Drawer 2
= 0: Allow close the Cash Drawer 2
Bit 1: Reserved
Bit 0: Cash Drawer1 “DOUT bit0” pin output control.
= 1: Opening the Cash Drawer 1
= 0: Allow close the Cash Drawer 1
/ 27
10
4.2.2.2Cash Drawer Status Register
Register Location: I/O port 206h
Attribute: Read
Size: 8bit
7 6 5 4 3 2 1 0
X X X X X X
Bit 7-2: Reserved
Bit 1: Cash Drawer2 “DIN bit1” pin input status.
= 1: the Cash Drawer2 opened or not exist.
= 0: the Cash Drawer2 closed.
Bit 0: Cash Drawer1 “DIN bit0” pin input status.
Cash Drawer1 “DIN bit0” pin input status
Cash Drawer2 “DIN bit1” pin input status
Reserved
= 1: the Cash Drawer1 opened or not exist.
= 0: the Cash Drawer1 closed.
/ 27
11
4.2.3Cash Drawer control command example
Use Debug.EXE program under DOS or Windows98
Command Cash Drawer 1
O 206 01 Opening
O 206 00 Allow to close
¾ Set the I/O address 206h bit0 =1 for opening Cash Drawer1 by “DOUT bit0” pin
control.
¾ Set the I/O address 206h bit0 =0 for allow close Cash Drawer1.
Command Cash Drawer 2
O 206 04 Opening
O 206 00 Allow to close
¾ Set the I/O address 206h bit2 =1 for opening Cash Drawer2 by “DOUT bit2” pin
control.
¾ Set the I/O address 206h bit2 =0 for allow close Cash Drawer2.
Command Cash Drawer
I 206 Check status
¾ The I/O address 206h bit0 =1 mean the Cash Drawer1 is opened or not exist.
¾ The I/O address 206h bit0 =0 mean the Cash Drawer1 is closed.
¾ The I/O address 206h bit1 =1 mean the Cash Drawer2 is opened or not exist.
¾ The I/O address 206h bit1 =0 mean the Cash Drawer2 is closed.
/ 27
12
5. Disassemble Procedures
a. Turn over the system and remove the stand by loosening the three screws.
b. Loosen the screw fastening the power
cover and the power bracket.
d. Loosen the screw fastening the power
bracket and the base chassis.
c. Remove the power supply.
e. Remove the power bracket.
f. Loosen the two screws fastening the
keypad cover.
/ 27
the screw fastening the LCD panel rear
cover and LCD panel.
13
g. Remove the keypad cover and loosen
h. Loosen the screw fastening the jumper setting cover and the base chassis to remove it.
i. Loosen the screws fastening the LCD panel rear cover and the panel to remove it.
j. Disconnect the keypad cable
k. Press the button to remove the CF card. l. Lift the base chassis.
/ 27
14
m. Disconnect the connector board cable,
n. Loosen the screws fastening the mother
audio cable and the connector board power
board and the LCD panel.
cable.
o. Loosen the two screws fastening the mother
board and the bridge board.
p. Lift the bridge board and disconnect the
panel signal cable.
q. Press the heat sink clip and lift it.
r. Remove the heatsink. s. Disconnect the card reader cable.
/ 27
15
t. Disconnect the I-button and the LED cable. u. Disconnect the inverter cable.
v. Disconnect the touch panel cable. w. Disconnect the two hexagonal screws.
x. Loosen the screws fastening the mother board and the LCD panel and remove it..
/ 27
16
SKT3
6. Jumper Setting
6.1 Main Board Jumper Setting
6.1.1 I-button Selection
Function JP1
Yes SHORT
No OPEN
6.1.2 Compact Flash Card Selection
Function JP2
SECONDARY SLAVE OPEN
SECONDARY MASTER SHORT
/ 27
17
6.1.3 Panel Type Selection
JP3 Function
1-2 3-4 5-6 7-8
DSTN OPEN SHORT OPEN SHORT
OPEN SHORT SHORT OPEN
TFT
OPEN SHORT SHORT SHORT
TFT LVDS
6.1.4 CMOS Clear Selection * Factory Default Setting
Function JP5 (SHORT)
* Normal 1-2
Clear 2-3
6.1.5 DIO Address Selection * Factory Default Setting
Function JP6
* 206H
386H SHORT
6.1.6 Panel Brightness Selection
Function JP8 (SHORT)
TFT 1-2
DSTN 2-3
6.1.7 PS2 Card Reader Selection(Add-on Card Reader or not)
Function
1-2 3-4
No SHORT SHORT
JP9
OPEN
Yes OPEN OPEN
Note:
OPEN
/ 27
18
SHORT
6.2 Connector Board Jumper Setting
a. This is the POS310 connector Board. Turn over the board…
b. And you will see JP1 and JP2 at the back.
JP1JP2
c. The Connector Board Jumper location of POS 310/312
/ 27
19
6.2.1 JP1
6.2.1.1 Cash drawer
CASH DRAWER
Pin (JP1) 1-2 3-4 5-6 7-8 9-10
Default ● ●
Function NC +24V +24V +12V +12V
6.2.1.2 COM1 and COM2
COM2 COM1
Pin (JP1) 11-12 13-14 15-16 17-18 19-20 21-22 23-24 25-26 27-28 29-30 31-32 33-34
Default ● ● ● ●
Function +12V 5V RI +12V 5V DCD +12V 5V RI +12V 5V DCD
Pin(COM) Pin 9 Pin 1 Pin 9 Pin 1
6.2.2 JP2
COM4 COM3
Pin (JP2) 1-2 3-4 5-6 7-8 9-10 11-12 13-14 15-16 17-18 19-20 21-22 23-24
Default ● ● ● ●
Function +12V 5V RI +12V 5V DCD +12V 5V RI +12V 5V DCD
Pin(COM) Pin 9 Pin 1 Pin 9 Pin 1
Note:
OPEN
/ 27
20
SHORT
7. Driver Installation
The follow procedures are for Windows XP, other platforms are similar.
7.1 Chipset Driver Installation
(Path: <CD>:\B46\VIA_4IN1)
a. Click "4in1443v" on the My Computer
window.
c. Click "Yes" button on the Readme
window.
b. Click "Next" button on the welcome
window.
d. Click "Next" button on the 4in1 Setup
Mode Option window.
e. Click ”Next” button on the Setup
Component window.
/ 27
f. Click “Next” button on the VIA PCI IDE
21
Bus Driver window.
g. Click “Next” button on the VIA_GART
h. Click “OK” button to restart the system.
AGP Driver window.
/ 27
22
7.2 LAN Driver Installation
(Path:<CD> :\Common\Lan_driver\ R8139_810x\9x_ME_2K_XP)
a. Click ”Setup” on the My computer
windows.
c. Click "Next" button on the InstallShield
Wizard complete window.
b. Click "Next" button on the InstallShield
Wizard window.
/ 27
23
7.3 Audio Driver Installation
(Path: <CD>:\B46\Audio\V4.50b)
a. Click ”Setup” on the My computer
windows.
c. Click "Next" button on the Select
Component window.
b. Click "Next" button on the welcome
window.
d. Click ”Finish” button to restart the system.
/ 27
24
7.4 Touch
Driver path in Driver Bank: COMMON\MION_Touch\WINXP\
a. Double-click Setup.exe
c. Select the location then click “Next”
b. Click “Next”
d. Click “Next”
e. Click “Next”
/ 27
25
f. Click “OK” to restart computer
8.Install touch driver on DOS mode
Driver path in Driver Bank: COMMON\MION_Touch\DOS\
a. Input command “install C:” to install the
driver to C
c. Input command “s” to run Touch screen
control panel window.
b. Input Command “m” to install driver
d. Select “Calibration” on Touch screen
control panel window.
e. Select “VGA 3h” and then click “Start”
/ 27
26
f-1. Touch the targets for alignment.
f-2. Touch the targets for alignment.
f-3. Touch the targets for alignment.
f-4. Touch the targets for alignment.
f-5 Touch the targets for alignment.
Note: You also can select other VGA mode you want. Please follow the installation
step e.
For Example: VGA 3h=> Text 80*25 16 color
VGA 4h=> Graph 320*200 4 color
/ 27
27
Loading...