Page 1
SIDE 1
Quick Start Guide
In-Home Pelvic Floor Treatment Model MTI-1
Please review the Instructions for Use, included with
the Flyte™ system, for complete information.
Check it out.
1
Visually inspect the
device before use for
anything unusual (cracks,
tears, exposed wires).
Choose place &
position.
4
Choose a private
area where you will
be able to concentrate
solely on the exercise for 5
continuous minutes.
Choose either a standing
or sitting position to use
the device for the duration
of the 5-minute therapy.
For best results, you
should remain still in the
same position for the full 5
minutes.
Charge it.
2 3
Before use, charge the device by plugging the USB
cable into the receptacle on the biofeedback unit.
Plug it into the wall. You will know Flyte™ is charging when
the charging light is yellow.
When the charging light turns o, the device is fully
charged and you should disconnect and store the charging
cable and unit. A full charge will take at least 2.5 hours.
Pelvital recommends that you recharge the battery weekly.
Insert the device.
5 6
Apply a small
amount of water-
based vaginal lubricant
to the wand or apply a
lubricated probe cover.
Get into position and fully
insert the wand into your
vagina, with the longer
wing facing the front of
your body. If you encounter
excessive discomfort,
remove the wand and
contact our customer care
team at 1-866-PELVITAL
or [email protected].
Plug in & turn on.
Once the wand is
inserted in your
vagina, plug the USB cable
on the end of the wand into
the biofeedback unit.
Turn Flyte™ on by pressing
the On/O button on
the bottom center of the
device for one second. The
product is on when the
green “On” indicator light is
displayed.
Clean & disinfect it.
Clean and disinfect the wand before its first use,
after each use, and again before each subsequent
use. Unplug the wand from the biofeedback unit prior to
cleaning the product.
To clean and disinfect the wand and biofeedback unit:
• Wash your hands.
• Use a clean, damp cloth to remove any obvious residue
from the wand.
• Use a Dispatch® Cleaner Disinfectant Towel (or
equivalent disinfecting wipe that contains no more than
1% sodium hypochlorite) to remove any residue from the
outside of the wand. Discard the wipe.
• Use a clean, damp cloth to remove residual cleaning
agent from the wand’s surface. NOTE: Use only a soft
cloth or wipe to clean the wand. Abrasive materials can
damage the wand.
• Use a second disinfecting wipe to disinfect the wand and
biofeedback unit, wiping all outside surfaces thoroughly.
Discard the wipe and allow the wand’s surface to remain
wet for 5 minutes.
WARNING: Do not submerge the biofeedback
unit, the charging cable, the wall charger, or the
wand in water.
• Apply mild soap to the wand and rinse thoroughly with
water to remove residue. Please ensure that all of the
soap is rinsed o. Wipe with a clean cloth, and then air
dr y.
USING THE DEVICE (SIDE 2)
Page 2
SIDE 2
Quick Start Guide
In-Home Pelvic Floor Treatment Model MTI-1
Questions? Visit us at www.pelvital.com or contact
Pelvital Customer Care at 1-866-PELVITAL or info@
pelvital.com.
Watch the center indicator light to guide you during the 5-minute therapy.
7
Do not squeeze (2 seconds) Squeeze & hold! (5 seconds) Rest (8 seconds)
With the product on and the wand inserted, it’s time to use Flyte™. The “Contract” light in the middle of the device will
tell you when to relax your pelvic floor muscles and when to contract (squeeze or tighten).
• Hold the biofeedback unit and look at the Contract light in the middle of the device.
• Rest until the Contract light turns green. Squeeze and hold your pelvic floor muscles for 5 seconds while the light is green.
You should also feel a vibration from the wand. When the Contract light turns o, rest your muscles. The rest period lasts
8 seconds, and the cycle begins again when the Contract light is orange. (Do not squeeze when the light is orange.)
• The cycle repeats 20 times during the 5-minute session and you’ll continue the process of squeezing and resting by
following along.
Observe the Contraction Indicator lights.
8
While you are repeating the relaxation and contraction, observe the Contraction Indicator
lights. These lights indicate the strength your pelvic floor muscle contractions. With each
contraction, try to activate all eight Contraction Indicator lights. Do not be discouraged if
you cannot activate all eight lights: Muscle tone and strength should improve over time.
End the day’s session.
9
After 5 minutes of
training, your therapy
is complete for the day and
Flyte™ will power down
automatically. You’ll know
the device is turned o
because the green light will
stop lighting up, and no
other indicator lights will be
displayed.
To end the day’s session,
complete the following
steps:
• Disconnect the
wand cable from the
biofeedback unit.
• Remove the wand from
your vagina.
• Clean the wand by
following the instructions
• Store the Flyte™ system
in the box until the next
session.
• Charge the device once
a week and you’re good
to go!
Part # LBL-0004-01
Loading...