Flymo Turbo 400 User Manual

GB
IMPORTANT INFORMATION
Read before use and retain for future reference
D
WICHTIGE INFORMATION
Bitte vor dem Benutzen des Gerätes durchlesen und gut aufbewahren
F
A lire avant usage et à conserver pour référence ultérieure
NL
BELANGRIJKE INFORMATIE
Leest u deze informatie voor het gebruik en bewaar ze voor toekomstige raadpleging
N
VIKTIG INFORMASJON
Les bruksanvisningen nøye før bruk og oppbevar den for senere bruk
S
VIKTIG INFORMATION
Läs anvisningarna före användningen och spara dem för framtida behov
DK
VIGTIGE OPLYSNINGER
Du bør læse brugsanvisningen før brug og gemme til senere henvisning
E
INFORMACIÓN IMPORTANTE
Léase antes de utilizar y consérvela como referencia en el futuro
P
INFORMAÇÕES IMPORTANTES
Leia antes de utilizar e guarde para consulta futura
I
INFORMAZIONI IMPORTANTI
Leggere prima dell’uso e conservare per ulteriore consultazione
SF
TÄRKEÄÄ TIETOA
Lue tämä ennen käyttöä ja säilytä myöhempää tarvetta varten
SK
Záruka na tento produkt nebude uznaná v prípade porúch spôsobených nesprávnou obsluhou alebo používaním výrobku na iný účel alebo iným spôsobom, ako je uvedené. Pred začatím práce si prosím dôkladne prečítajte návod na obsluhu a tento si aj pre prípad potreby uschovajte
SL
Garancija ne velja ob nepravilni uporabi proizvoda in/ali ob uporabi za drugi namen kot je izdelan. Prosimo, da pred uporabo, preverite pazljivo navodila za obratovanje in jih shranite za kasnejšo rabo.
HU
Jótállást vállalni csak rendeltetésszerűen használatba vett gépekre tudunk. Kérjük, hogy a gép használatba vétele elött gondosan olvassa el a kezelési utasításokat.
PL
Gwarancja traci ważność w przypadku używania urządzenia do celów innych niż wymienione w instrukcji obsługi. Prosimy o uważne przeczytanie instrukcji oraz o stosowanie się do zaleceń i wskazówek w niej zawartych
CZ
Záruka se nebude vztahovat na závady způsobené nesprávným používáním, nebo jestliže bude výrobek použit pro jiné účely než pro jaké byl vyroben, nebo také jinak než je uvedeno v návodu k obsluze. Tento návod si přečtěte, prosím, velmi pozorně a uchovejte jej pro možné budoucí odkazy
Turbo Lite 330/350
Turbo 400
E
CH
F
G
D
CH
A B
1
4
3
2
1
3
2
C
5
CH
H
1
J
K
1
2
L
M
Turbo Lite 330
Turbo Lite 350/Turbo 400
3
4
N
GB - CONTENTS
1. Upper handle
2. Cable clip
3. Nut (if applicable)
4. Plastic handle knob
5. Washer
6. Bolt
8. Lower handle
9. Fixing pin
9. Spanner/scraper tool
10. Cutting height spacers (Turbo Lite 330 - 1 fitted to lawnmower & 2 in loose parts pack) (Turbo Lite 350/Turbo Lite 350/Turbo 400 - 1 fitted to lawnmower & 3 in loose parts pack)
11. Instruction Manual
12. Warning Label
13. Product Rating Label
D - INHALT
1. Oberer Griff
2. Kabelhalter
3. Mutter (falls vorhanden)
4. Griffknopf
5. Unterlegscheibe
6. Bolzen
7. Unterer Griff
8. Paßstift
9. Schraubenschlüssel/ Reinigungswerkzeug
10. Schnitthöhen-Distanzscheiben (Turbo Lite 330 - 1 befindet sich am Rasenmäher & 2 werden lose in einem Beutel geliefert), (Turbo Lite 350/Turbo 400 - 1 befindet sich am Rasenmäher & 3 werden lose in einem Beutel geliefert)
11. Bedienungsanweisung
12. Warnetikett
13. Produkttypenschild
F - TABLE DES MATIÈRES
1. Guidon supérieur
2. Attache câble
3. Ecrou (si applicable)
4. Bouton de Guidon
5. Rondelles
6. Boulons
7. Guidon inférieur
8. Chevilles de fixation
9. Raclette
10. Rondelles de réglage (Turbo Lite 330 - 1 montée sur la tondeuse et 2 dans les pièces détachées), (Turbo Lite 350/Turbo 400 - 1 montée sur la tondeuse et 3 dans les pièces détachées)
11. Manuel d’Instructions
12. Etiquette d’avertissement
13. Plaquette des Caractéristiques du Produit
NL - INHOUD
1. Bovenstuk van duwboom
2. Snoerklem
3. Moer (indien van toepassing)
4. Knop voor duwboom
5. Pakkingring
6. Bout
7. Onderstuk van duwboom
8. Bevestigingspin
9. Moersleutel/schraapinstrument
10. Snijhoogte-tussenstukken (Turbo Lite 330 - 1 in grasmaaimachine en 2 in pak met losse onderdelen), (Turbo Lite 350/Turbo 400 - 1 in grasmaaimachine en 3 in pak met losse onderdelen)
11. Handleiding
12. Waarschuwingsetiket
13. Product-informatielabel
N - INNHOLD
1. Øvre håndtak
2. Kabelklemmer
3. Mutter (om relevant)
4. Vingemuttere
5. Skiver
6. Håndtaksbolter
7. Nedre håndtak
8. Festebolt
9. Skrunøkkel/skrape
10. Avstandsstykker for justering av klippehøyden (Turbo Lite 330 – 1 montert på gressklipperen & 2 i pakken med løse deler), (Turbo Lite 350/Turbo 400 – 1 montert på gressklipperen & 3 i pakken med løse deler)
11. Bruksanvisning
12. Advarselsetikett
13. Produktmerking
SF - SISÄLTÖ
1. Ylempi kahva
2. Johdon pidike
3. Mutteri (jos käytössä)
4. Kahvan nuppi
5. Tiivistysrengas
6. Pultti
7. Alempi kahva
8. Kiinnitystappi
9. Ruuviavain/kaavin
10. Leikkauskorkeuden säätölevy (Turbo Lite 330 - 1 asennettu ruohonleikkuriin ja 2 pakkauksessa), (Turbo Lite 350/Turbo 400 - 1 asennettu ruohonleikkuriin ja 3 pakkauksessa)
11. Käyttöopas
12. Varoitusnimike
13. Ruohonleikkurin arvokilpi
S - INNEHÅLL
1. Övre handtag
2. Kabelklämma
3. Mutter (om sådan är monterad)
4. Knopp för handtag
5. Bricka
6. Bult
7. Undre handtag
8. Fästbult
9. Skruvnyckel/Avskrapare
10. Distansbrickor för klipphöjd (Turbo Lite 330 - 1 monterad på gräsklipparen och 2 lösa i förpackning), (Turbo Lite 350/Turbo 400 - 1 monterad på gräsklipparen och 3 lösa i förpackning)
11. Bruksanvisning
12. Varningsetikett
13. Produktmärkning
DK - INDHOLD
1. Øvre håndtag
2. Kabelklemme
3. Møtrik (hvis relevant)
4. Håndtagsknop
5. Spændeskive
6. Bolt
7. Nedre håndtag
8. Håndtagsstift
9. Skruenøgle/skrabeværktøj
10. Afstandsskiver til indstilling af klippehøjde (Turbo Lite 330 - 1 monteret på plæneklipperen og 2 løse i posen) (Turbo Lite 350/Turbo 400 - 1 monteret på plæneklipperen og 3 løse i posen)
11. Brugsvejledning
12. Advarselsmœrkat
13. Produktets mærkeskilt
E - CONTENIDO
1. Empuñadura superior
2. Grapa de cable
3. Tuerca (si fuera aplicable)
4. Manija de empuñadura
5. Arandela
6. Perno
7. Empuñadura inferior
8. Pasador de fijación
9. Herramienta/raspador
10. Espaciadores de altura de corte (Turbo Lite 330 – 1 instalado en el cortacésped y 2 en paquete de piezas sueltas) (Turbo Lite 350/Turbo 400 – 1 instalado en el cortacésped y 3 en paquete de piezas sueltas)
11. Manual de instrucciones
12. Etiqueta de Advertencia
13. Placa de Características del Producto
P - LEGENDA
1. Guiador superior
2. Grampo do cabo
3. Porca (se aplicável)
4. Maçaneta
5. Anilha
6. Cavilha
7. Guiador inferior
8. Parafuso
9. Chave de fendas
10. Espaçadores da altura de corte (Turbo Lite 330 – 1 instalado na máquina de cortar relva e 2 no pacote de peças soltas), (Turbo Lite 350/Turbo 400 – 1 instalado na máquina de cortar relva e 3 no pacote de peças soltas)
11. Manual de Instrucções
12. Etiqueta de Aviso
13. Rótulo de Avaliação do Produto
I - INDICE CONTENUTI
1. Impugnatura superiore
2. Morsetto per il cavo
3. Dado (se pertinente)
4. Manopola
5. Rondella
6. Bullone
7. Impugnatura inferiore
8. Perno di fissaggio
9. Chiave/raschietto
10. Distanziali altezza di taglio (Turbo Lite 330 - 1 montato sul tosaerba e 2 sfusi nel sacchettino dei ricambi), (Turbo Lite 350/Turbo 400 - 1 montato sul tosaerba e 3 sfusi nel sacchettino dei ricambi)
11. Manuale di istruzioni
12. Etichetta di pericolo
13. Etichetta dati del prodotto
HU - TARTALOMJEGYZÉK
1. Felső tolókar
2. Kábelrögzítő
3. Anya (ha van)
4. Rögzítőgomb
5. Alátét
6. Csavar
7. Alsó tolókar
8. Rögzítőcsap
9. Csavarkulcs/térközbeállító szerszám
10. Vágómagasság-beállítók (Turbo Lite 330 - 1 db be van szerelve, 2 db a külön alkatrész-csomagolásban található), (Turbo Lite 350/Turbo 400 - 1 db be van szerelve, 3 db a külön alkatrész-csomagolásban található)
11. Kezelési útmutatő
12. Figyelmeztető címke
13. Termékminősítő címke
PL - ZAWARTOSC KARTONU
1. Górny uchwyt
2. Zaczep kabla
3. Nakrętka (jeżeli jest)
4. Gałka mocująca
5. Podkładka
6. Śruba
7. Dolny uchwyt
8. Sworzeń mocujący
9. Klucz/skrobak
10. Rozpórki ustalające wysokość koszenia. (model Turbo Lite 330 - jedna rozpórka jest zamontowana w kosiarce natomiast dwie znajdują się w pakiecie z luźnymi częściami). (model Turbo Lite 350/Turbo 400 - jedna rozpórka jest zamontowana w kosiarce natomiast trzy rozpórki znajdują się w pakiecie z luźnymi częściami)
11. Instrukcja Obsługi
12. Znaki bezpieczeństwa
13. Tabliczka znamionowa
CZ - POPIS STROJE
1. Horní rukoje
2. Úchytka kabelu
3. Matice (pokud se používá)
4. Otočný knoflík na rukojeti
5. Podložka
6. Šroub
7. Spodní rukoje
8. Spojovací kolík
9. Klíč/nástroj pro čištění
10. Distanční tělíska výšky sekání (Turbo Lite 330 - 1 instalováno na sekačce a 2 v balíku s náhradními díly), (Turbo Lite 350/Turbo 400 ­1 instalováno na sekačce a 3 v balíku s náhradními díly)
11. Návod k obsluze
12. Výstražný štítek
13. Typový štítek výrobku
SK - OBSAH
1. Vrchná rukovä
2. Svorka na kábel
3. Matka (ak aplikovate?né)
4. Kĺb rukoväte
5. Podložka
6. Skrutka
7. Spodná rukovä
8. Upevňovací kolík
9. K?úč/škrabka
10. Sekacie medzerníky výšky (Turbo Lite 330 - 1 upevnený ku kosačke a 2 v balíčku vo?ných častí), (Turbo Lite 350/Turbo 400 - 1 upevnený ku kosačke a 3 v balíčku vo?ných častí)
11. Príručka
12. Varovný štítok
13. Prístrojový štítok
SL - VSEBINA
1. Zgornje držalo
2. Sponka za kabel
3. Matica (če je priložena)
4. Pritrdilna matica
5. Podložka
6. Vijak
7. Spodnje držalo
8. Pritrdilni trn
9. Ključ/strgalo
10. distančniki za višino reza (Turbo Lite 330 - 1 montiran v kosilnici in 2 v zavitku z rezervnimi deli), (Turbo Lite 350/Turbo 400 - 1 montiran v kosilnici in 3 v zavitku z rezervnimi deli)
11. Priročnik
12. Opozorilna oznaka
13. Tipna tablica
1
(GB) CARTON CONTENTS (D) KARTONINHALT (F) CONTENU DU CARTON (NL) INHOUD (N) KARTONGEN
INNEHOLDER
(SF) PAKETIN SISÄLTÖ
(S) FÖRPACKNINGENS
INNEHÅLL (DK) KARTONINDHOLD (E) CONTENIDO DEL
CARTON (P) LEGENDAS DOS
DESENHOS
(I) CONTENUTO
(HU) A DOBOZ TARTALMA (PL) ZAWARTOŚĆ KARTONU (CZ) OBSAH KRABICE (SK) OBSAH BALENIA (SL) VSEBINA ŠKATLE
1
2
6
5
4
7
8
9
10
13
12
11
3
SAFETY PRECAUTIONS
Explanation of Symbols on the Turbo Lite 330/350/Turbo 400
Warning
Read the user instructions carefully to make sure you understand all the controls and what they do.
Always keep the lawnmower on the ground when mowing. Tilting or lifting the lawnmower may cause stones to be thrown out
Keep bystanders away. Do not mow whilst people especially children or pets are in the mowing area
Switch off! Remove plug from mains before adjusting, cleaning or if cable is entangled or damaged. Keep the cable away from the blade.
Beware of severing toes or hands. Do not put hands or feet near a rotating blade.
Blade continues to rotate after the machine is switched off. Wait until all machine components have completely stopped before touching them.
Do not mow in the rain or leave the lawnmower outdoors while raining
General
1. Never allow children or people unfamiliar with these instructions to use the mower. Local regulations may restrict the age of the operator.
2. Only use the lawnmower in the manner and for the functions described in these instructions.
3. Never operate the lawnmower when you are tired, ill or under the influence of alcohol, drugs or medicine.
4. The operator or user is responsible for accidents or hazards occurring to other people or their property.
Electrical
1. The use of a Residual Current Device (R.C.D.) with a tripping current of not more than 30mA is recommended. Even with a R.C.D. installed 100% safety cannot be guaranteed and safe working practice must be followed at all times. Check your R.C.D. every time you use it.
2. Before use, examine cable for damage, replace it if there are signs of damage or ageing.
3. Do not use the lawnmower if the electric cables are damaged or worn
4. Immediately disconnect from the mains electricity supply if the cable is cut, or the insulation is damaged. Do not touch the electric cable until the electrical supply has been disconnected. Do not repair a cut or damaged cable. Replace it with a new one.
5. Your extension cable must be uncoiled, coiled cables can overheat and reduce the efficiency of your mower.
6. Keep cable away from lawnmower, always work away from the power point mowing up and down, never in circles.
7. Do not pull cable around sharp objects.
8. Always switch off at the mains before disconnecting any plug, cable connector or extension cable.
9. Switch off, remove plug from mains and examine electric supply cable for damage or ageing
befor
e winding cable for storage. Do not repair a
damaged cable, replace it with a new one. Use only Flymo replacement cable.
10. Always wind cable carefully, avoiding kinking.
11. Never carry the product by the cable.
12. Never pull on the cable to disconnect any of the plugs.
13. Use only on AC mains supply voltage shown on the product rating label.
14. Our products are double insulated to EN60335. Under no circumstance should an earth be connected to any part of the product.
Cables
Use only 1.00mm
2
size cable up to 30 metres length
maximum.
Maximum rating:
1.00mm
2
size cable 10 amps 250 volts AC
1. Mains cables and extensions are available from your local Electrolux Outdoor Products Approved Service Centre.
2. Only use extension cables specifically designed for outdoor use.
Preparation
1. Do not mow barefoot or in open sandals. Always wear suitable clothing, gloves, and stout shoes.
2. Make sure the lawn is clear of sticks, stones, bones, wire and debris; they could be thrown by the blade.
If not used properly this lawnmower can be dangerous! This lawnmower can cause serious injury to the operator and others, the warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this lawnmower. The operator is responsible for following the warning and safety instructions in this manual and on the lawnmower.
ENGLISH - 1
STOP
SAFETY PRECAUTIONS
3. Before using the machine and after any impact, check for signs of wear or damage and repair as necessary.
4. Replace worn or damaged blades together with their fixings in sets to preserve balance.
Use
1. Use the lawnmower only in daylight or good artificial light.
2. Avoid operating your lawnmower in wet grass, where feasible.
3. Take care in wet grass, you may lose your footing.
4. On slopes, be extra careful of your footing and wear non-slip footwear.
5. Mow across the face of slopes, never up and down.
6. Exercise extreme caution when changing direction on slopes. Walk never run.
7. Mowing on banks and slopes can be dangerous. Do not mow on banks
or steep slopes.
8. Do not walk backwards when mowing, you could trip.
9. Never cut grass by pulling the mower towards you.
10. Switch off before pushing the mower over surfaces other than grass.
11. Never operate the lawnmower with damaged guards or without guards in place.
12. Keep hands and feet away from the cutting means at all times and especially when switching
on the motor.
13. Do not tilt lawnmower when the motor is running, except when starting and stopping. In this case, do not tilt more than absolutely necessary and lift only the part which is away from the operator. Always ensure that both hands are in the operating position before returning the appliance to the ground.
14. Never pick up or carry a mower when it is operating or still connected to the mains supply.
15. Remove the plug from the mains :
- before leaving the mower unattended for any period;
- before clearing a blockage;
- before checking, cleaning or working on the appliance;
- if you hit an object. Do not use your lawnmower until you are sure that the entire lawnmower is in a safe operating condition.;
- if the lawnmower starts to vibrate abnormally. Check immediately. Excessive vibration can cause injury.
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be sure the lawnmower is in safe working condition.
2. Replace worn or damaged parts for safety.
3. Only use the replacement blade, blade bolt, spacer and impeller specified for this product.
4. Be careful during adjustment of the lawnmower to prevent entrapment of the fingers between moving blades and fixed parts of the machine.
ENGLISH - 2
ASSEMBLY
A1 - lower handle A2 - slots A3 - fixing pin Fitting the Lower Handles to Your Lawnmower (A)
1. Place the end of the lower handle into the slots.
2. Secure lower handles to hood by firmly pushing fixing pin through holes in hood and handle.
3. Repeat on the other side.
• NOTE
Should a problem occur when securing handle to hood with the fixing pin, carefully lever fixing pin out of location and repeat steps 1 to 3 above.
B1 - lock off button, B2 - nut (if applicable) B3 - handle knob, B4 - washer, B5 - bolt Fitting Upper Handles to Lower Handles (B)
1. Ensure the upper handle is located correctly with the lock-off button on the switchbox uppermost.
2. Ensure the upper handle and the lower handle are aligned correctly.
3. Insert the nut into the handle knob. (if applicable)
4. Fit the bolts, washers and handle knobs.
5. Fit the cable to the handles with the clips provided. Make sure the cable is not trapped between the upper and lower handles.
HANDLE ADJUSTMENT
• WARNING! STOP THE LAWNMOWER AND WAIT UNTIL THE BLADE HAS STOPPED ROTATING BEFORE ADJUSTING THE HANDLE.
• NOTE! REMOVAL OF LOWER HANDLE FIXING PINS IS NOT REQUIRED
TO ADJUST
THE HANDLE
TO ADJUST THE HANDLE (C)
1. Hold handle as illustrated.
2. Take the weight of the handle with your right hand...
3. ...then grip the lower part of the handle with your
left hand...
4. ...and pull
the lower handle towards you with
your left hand.
5. Move to forward or down position as required.
HANDLE IN FORWARD POSITION
Follow procedure described in "TO ADJUST THE HANDLE" and push handle forward until it stops.
HANDLE IN DOWN POSITION
Follow procedure described in "TO ADJUST THE HANDLE" and move handle downward until it stops..
NOTE - The handle does not rest flat on the ground.
HANDLE IN OPERATING POSITION Adjustment is not required to move the handle to the operating position
Simply pull down from the forward position or
lift up from the down position until the handle is in the most comfortable operating position.
REMOVING AND FITTING THE BLADE AND FAN
K1 - Blade Bolt K2 - Blade K3 - Spacers K4 - Fan Removing the Blade and Fan
1. To remove the blade bolt, hold the fan firmly and with the spanner provided loosen the blade bolt by turning it anti-clockwise (L).
2. Remove the blade bolt, blade, spacers and fan.
3. Inspect for damage and clean as necessary.
• Renew your metal blade after 50 hours mowing or 2 years whichever is the sooner ­regardless of condition.
Fitting the Blade and Fan
• If the blade is cracked or damaged replace it with a new one.
• Never use a blade bolt if the insulated head is damaged cracked or missing.
1. Ensure the fan is located correctly.
2. Place the spacers onto the fan ensuring the pegs have located into the holes.
3. Place the blade onto the spacers ensuring the pegs have located into the holes on the blade and ensuring the blade is positioned as illustrated in Figure M.
4. Place the blade bolt through the centre hole of the blade.(M)
5. Tighten down clockwise by hand.
6. Hold the fan firmly and tighten the blade bolt with the spanner provided.
ENGLISH - 3
HOW TO MOW
1. Start mowing the edge of the lawn nearest to the power point so the cable is laid out on the lawn you have already cut. (J)
2. Cut your grass twice a week during the growing season, your lawn will suffer if more than a third of its length is cut at one time.
Do Not Overload Your Mower
Mowing long thick grass may cause the motor speed to drop, you will hear a change in the motor sound. If the motor speed drops you may overload your lawnmower which may cause damage. When mowing in long thick grass a first cut with the cutting height set higher will help reduce the load. See Adjusting the Cutting Height.
STARTING AND STOPPING
To Start your Lawnmower
1. Connect female extension cable connector to the back of the switchbox (D).
2. Form loop in mains cable and push the loop through the slot as illustrated in picture (E)
3. To secure, position loop over the hook and pull the cable back through the slot as illustrated in picture (F).
4. Connect plug to mains and switch on.
5. To prevent a ring being cut in your lawn and to clear any residual grass in the collection chute, tilt your lawnmower slightly (G).
The switchbox is provided with a lock-off button (H1) to prevent accidental starting.
6. Press and hold the lock-off button (H) on the switchbox, then squeeze one of the Start/Stop levers towards the upper handle (H).
7. Continue to squeeze the start/stop lever towards the upper handle and release the lock­off button.
8. When the lawnmower has reached full speed gently lower it onto the lawn.
• NOTE There are two start/stop levers fitted. Either one can be used for starting the lawnmower.
• IMPORTANT Do not use the start/stop levers intermittently
To Stop your Lawnmower
1. To prevent a ring being cut in your lawn and to clear any residual grass in the collection chute, tilt your lawnmower slightly (G).
2. Release the pressure on the Start/Stop lever.
ADJUSTING THE CUTTING HEIGHT
Always handle the blade with care - sharp edges could cause injury. USE GLOVES. Never use more than 3 Cutting Height Spacers for the Turbo Lite 330 OR 4 Cutting Height Spacers for the Turbo Lite 350/Turbo 400. Spacers must only be fitted between the blade and the fan and NEVER between the blade and the bolt.
1. Remove the blade bolt, and blade as described in Removing the Blade and Fan.
2. For a Lower Cut - Add spacers to a maximum of 3 for Turbo Lite 330, or 4 for Turbo Lite 350/Turbo 400.
3. For a Higher Cut - Take spacers away.
4. Refit the blade as described in Fitting the
Blade and Fan.
SERVICE RECOMMENDATIONS
• Your product is uniquely identified by a silver and black product rating label.
• We strongly recommend that your product is serviced at least every twelve months, more often in a professional application.
ENGLISH - 4
CARING FOR YOUR LAWNMOWER
Cleaning (USE GLOVES) (N) It is very important that you keep your lawnmower clean. Grass clippings left in any of the air intakes or under the hood could become a potential fire hazard.
1. Remove grass from under the hood with a piece of wood or similar.
2. Using a soft brush - remove grass clippings from
all
air intakes.
3. Remove the blade, see Figure L, to gain access to the fan and clean with a soft brush.
4. Wipe over the surface of your lawnmower with a dry cloth.
• IMPORTANT: Never use water for cleaning your lawnmower. Do not clean with chemicals, including petrol, or solvents - some can destroy critical plastic parts.
At the End of the Mowing Season
1. Replace blade, bolts, nuts or screws, if necessary.
2. Clean your lawnmower thoroughly.
3. Ask your local Service Centre to clean the air filter thoroughly and carry out any service or repairs required.
4. Make sure that the electric cable is coiled properly.
Carrying your Lawnmower Ensure the blade is facing away from you.
Storing your Lawnmower
Store in a dry place where your lawnmower is protected from damage.
FAULT FINDING HINTS
Fails to Operate
1. Is the Power Turned On?
2. Check the fuse in the plug, if blown replace.
3. Fuse continues to blow?
Immediately disconnect from the mains electricity supply and consult your local approved Service Centre.
Poor Flotation
1. Disconnect from the mains electricity supply.
2. Clean the underside of the hood and the fan blades.
3. Raise to a higher height of cut. See Adjusting the Height of Cut.
4. If poor flotation persists?
Disconnect from the mains electricity supply and consult your local approved Service Centre.
Excessive Vibration
1. Disconnect from the mains electricity supply.
2. Check that the blade is fitted correctly?
3. If the blade is damaged or worn, replace it with a new one.
4. If vibration persists?
Immediately disconnect from the mains electricity supply and consult your local approved Service Centre.
GUARANTEE AND GUARANTEE POLICY
If any part is found to be defective due to faulty manufacture within the guarantee period, Electrolux Outdoor Products, through its Authorised Service Repairers will effect the repair or replacement to the customer free of charge providing: (a) The fault is reported directly to the Authorised
Repairer. (b) Proof of purchase is provided. (c) The fault is not caused by misuse, neglect or faulty
adjustment by the user. (d) The failure has not occurred through fair wear and
tear. (e) The machine has not been serviced or repaired,
taken apart or tampered with by any person not
authorised by Electrolux Outdoor Products. (f) The machine has not been used for hire. (g) The machine is owned by the original purchaser. (h) The machine has not been used outside of the
country for which it was specified. (i) The machine has not been used commercially. * This guarantee is additional to, and in no way
diminishes the customers statutory rights.
Failures due to the following are not covered, therefore it is important that you read the instructions contained in this Operator's Manual and understand how to operate and maintain your machine:
Failures not covered by guarantee
* Replacing worn or damaged blades * Failures as a result of not reporting an initial fault. * Failures as a result of sudden impact. * Failures as a result of not using the product in
accordance with the instructions and recommendations contained in this Operator's Manual.
* Machines used for hire are not covered by this
guarantee.
* The following items listed are considered as wearing
parts and their life is dependent on regular maintenance and are, therefore not normally subject to a valid warranty claim: Blades, Electric Mains cable.
* Caution! Electrolux Outdoor Products does not
accept liability under the warranty for defects caused in whole or part, directly or indirectly by the fitting of replacement parts or additional parts that are not either manufactured or approved by Electrolux Outdoor Products, or by the machine having been modified in any way.
ENVIRONMENTAL INFORMATION
Electrolux Outdoor Products are manufactured under an Environmental Management System (ISO 14001) using, where practical, components manufactured in the most environmentally responsible manner, according to company procedures, and with the potential for recycling at the end of the products’ life.
Packaging is recyclable and plastic components have been labelled (where practical) for categorised recycling.
Awareness of the environment must be considered when disposing of ‘end-of-life’ product.
If necessary, contact your local authority for disposal information.
BELGIQUE/BELGIË Flymo Belgique/België
Tel: 02 363 0311, Fax: 02 363 0391
ČESKÁ REPUBLIKA Electrolux, spol. s.r.o., oz Electrolux Outdoor Products,
Na Křečku 365, Praha 10 - Horní Měcholupy. Tel: 02/7847 0164, Info-linka: 0800/110 220 Internet: www.partner-flymo.cz E-mail: info@husqvarna.cz
DANMARK Electrolux Outdoor Products, Flymo/Partner A/S,
Lundtoftegaardsvej 93A, DK 2800 Kgs.Lyngby Tel: 45 87 75 77, Fax: 45 93 33 08, www.flymo-partner.dk
DEUTSCHLAND Flymo Deutschland
Tel: 097 21 7640, Fax:097 21 764202
ESTONIA Electrolux Estonia Ltd (Electrolux Eesti AS)
Tel: (372) 6650010
FRANCE Flymo France SNC
Tel 01 46 67 8141, Fax 01 43 34 2491
FINLAND SUOMI Electrolux Outdoor Products Finland
Tel: 00 358 9 39611, Fax: 00 358 9 3961 2644
ITALIA McCulloch Italiana s.r.l. - Via Como 72, 23868 Valmadrera
(LECCO) - ITALIA Tel: 800 017829, Fax: 0341 581671
IRELAND Flymo Ireland
Tel: 01 4565222, Fax: 01 4568551
MAGYARORSZÁG Electrolux Lehel Kft
Tel: 00 36 1 251 41 47
NORGE Flymo/Partner, div. av Electrolux Motor a.s.
Tel: 69 10 47 90
NEDERLAND Flymo Nederland
Tel: 0172-468322, Fax: 0172-468219
ÖSTERREICH Husqvarna-Ges.m.b.H. Nfg. KG, Industriezeile 36, 4010 LINZ,
Tel: 0732 770101-0, Fax: 0732 770101-40, email: office@husqvarna.co.at Internet: www.husqvarna.at
POLSKA Electrolux Poland Sp. z.o.o. Husqvarna, 01-612 Warszawa
Myslowicka 10/2 Tel:- (22) 8332949
SLOVENIJA Husqvarna-Ges.m.b.H. Nfg. KG, Industriezeile 36, 4010 LINZ,
Tel: 0732 770101-0, Fax: 0732 770101-40, email: office@husqvarna.co.at Internet: www.husqvarna.at
SLOVENSKA Electrolux Slovakia s.r.o., Borova Sihot 211, 033 01 Lipt. Hradok
Tel: 044 522 14 19, Fax: 044 522 14 18, www.flymo-partner.sk
SCHWEIZ/SUISSE/SUIZZERA Flymo Schweiz/Suisse/Suizzera
Tel 062 889 93 50 / 889 94 25, Fax 062 889 93 60 / 889 94 35
SVERIGE Electrolux Outdoor Products, Sverige
Tel: 036 – 14 67 00, Fax: 036 – 14 60 70
UNITED KINGDOM Electrolux Outdoor Products United Kingdom
Tel: 01325 300303, Fax: 01325 310339
5119252-02
Electrolux Outdoor Products
Aycliffe Industrial Park
NEWTON AYCLIFFE
Co.Durham DL5 6UP
ENGLAND
Telephone - (00) 44 1325 300303 Fax - (00) 44 1325 310339
UK Telephone - 01325 300303 Fax - 01325 310339
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice. Electrolux Outdoor Products manufacture products for a number of well known brands under various registered patents, designs and
trademarks in several countries.
© Electrolux Outdoor Products Ltd. Registered Office, Electrolux Works, Oakley Road, Luton LU4 9QQ
Registered number 974979 England
The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million
Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are
sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.
The Electrolux Group. The world’s No.1 choice.
Loading...