Flymo Contour 650E, Contour 500E, Contour 580E Operation Instructions Manual

Download

Contour 500E CTE25 Contour 580E CTE27 Contour 650E CTE30

GB Operation Instructions

Turbotrimmer

CLICK!

2 3

O10

FLYMO Turbotrimmer Contour 500E / 580E / 650E

Table of Contents:

1. SAFETY ........................................................................ 4

2. ASSEMBLY .................................................................. 5

3. OPERATION ................................................................. 5

4. MAINTENANCE ............................................................ 6

5. STORAGE .................................................................... 7

6. TROUBLESHOOTING ..................................................7

7. TECHNICAL DATA ....................................................... 8

8. ACCESSORIES ............................................................ 9

9. Service / Warranty ......................................................... 9

The initial language of these instructions is English. Other language versions are translations of the initial instructions.

This product may be used under supervision, or if instruction regarding the safe use of the

product has been provided and the resulting dangers have been understood, by children aged 8 and above, as well as by persons with physical, sensory or mental disabilities or a lack of experience and knowledge. Children must not be allowed to play with the product. Cleaning and user maintenance must not be performed by children without super vision. The use of this product by young people under the age of 16 is not recommended. Never operate the product when you are tired, ill or under the influence of alcohol, drugs or medicine.

360°

Intended use:

The FLYMO Turbotrimmer is used to trim and to cut grass and lawns in private house and hobby gardens.

Do not use the product in public facilities, parks, sports grounds, adjacent to roads or in agriculture or forestry.

1. SAFETY

Symbols on the product:

Read operator’s manual.

Keep other persons away. Danger!

Risk of injury to other persons!

v Keep other persons out of the

Wear safety glasses and

ear protection.

Do not let t he product become wet with

rain or othe r moistur e. Do not leave

the product outdoors while it is raining.

Disconnec t the mains cabl e if

the cable becomes damaged or

entangled.

General safety warnings

Important

Read carefully before use. Keep for further reference.

Safe operating practices

Training

a) Read the instructions carefully. Be familiar with the

controls and the correct use of the machine.

b) Never allow children or people unfamiliar with these

instructions to use the machine. Local regulations can restrict the age of operator.

c) Keep in mind that the operator or user is responsible

for accidents or hazards occurring to other people or their property.

Preparation

a) Before use check the supply and extension cord for

signs of damage or aging. If the cord becomes damaged during use, disconnect the cord from the supply immediately. DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE SUPPLY. Do not use the machine if the cord is damaged or worn.

b) Before use, always visually inspect the machine for

damaged, missing or misplaced guards or shields.

c) Never operate the machine while people, especially

children, or pets are nearby.

work area.

DANGER! Risk of injury! Do not use the product to cut hedges, to shred or to make compost.

Operation

a) Keep supply and extension cords away from cutting

means.

b) Wear eye protection and stout shoes at all times while

operating the machine.

c) Avoid using the machine in bad weather conditions

especially when there is a risk of lightning. d) Use the machine only in daylight or good artificial light. e) Never operate the machine with damaged guards or

shields or without guards or shields in place. f) Switch on the motor only when the hands and feet are

away from the cutting means. g) Always disconnect the machine from the power

supply (i.e. remove the plug from the mains, remove

the disabling device or removable battery).

1) whenever the machine is left unattended;

2) before clearing a blockage;

3) before checking, cleaning or working on the machine;

4) after striking a foreign object;

5) whenever the machine starts vibrating abnormally.

h) Take care against injury to feet and hands from the

cutting means. i) Always ensure that the ventilation openings are kept

clear of debris.

Maintenance and storage

a) Disconnect the machine from the power supply

(i. e. remove the plug from the mains, remove the

disabling device or removable battery) before carry-

ingout maintenance or cleaning work. b) Use only the manufacturer’s recommended replace-

ment parts and accessories. c) Inspect and maintain the machine regu larly. Have the

machine repaired only by an authorized repairer. d) When not in use, store the machine out of reach of

children.

Recommendation

The machine should be supplied via a resid ual current device (RCD) with a tripping current of not more than 30 mA.

Cables

Use only permitted extension cables as per HD 516. v Ask your electrical specialist. If the unit got hot during operation, let it cool down before

storage.

Additional Safety warnings

Warning! Keep toddlers away when you assemble the unit. Small parts can be easily swallowed. There is also

a risk that the polybag can suffocate toddlers.

Warning! When wearing hearing protection, and due to the noise produced by the unit, the operator may not notice persons approaching.

If the unit starts unintentionally when the mains plug is connected, disconnect the mains at once. Contact FLYMO Service to check the unit.

Warning! This unit makes an electromagnetic field while it operates. This field may under some con ditions interfere with active or passive medical implants. To decrease the risk of conditions that can possibly injure or kill, we recommend persons with medical implants to speak with their physician and the medical implant manufacturer before operating. If your trimmer is damaged in any way contact your local approved service centre.

v Never use a damaged trimmer. Inspect the area to be cut before each use. Remove all

objects such as stones, broken glass, nails, wire, string etc, which can be thrown or become entangled in the trimmer head.

2. ASSEMBLY

CAUTION! The trimmer may only be operated provided

that the protective cover

To assemble the trimmer:

1. Insert the tube into the switch handle [Fig. A1].

Make sure that the internal cable is not twisted.

2. Push until it clicks into position.

Make sure that the tube is fully located by attempting to remove it.

3. Insert the tube into the trimmer head [Fig. A2].

Make sure that the internal cable is not twisted.

4. Push until it clicks into position.

Make sure that the tube is fully located by attempting to remove it.

5. Pull the lock push in both of the snap-fits

belonging to the additional handle 2,

is assembled.

belonging to the

3. OPERATION

Warning: The cutting line continues to rotate after

the machine has been switched off.

Warning: Beware of finger entrapment while putting the upper and the lower shaft together [Fig. A1].

Unplug the device immediately in case it doesn’t stop anymore.

Do not lean over the trimmer guard – objects may be thrown by the cutting line.

Don’t use the trimmer for pond, river, stream, or creek care. Water in the product could cause a malfunction, or an electrical shock.

Do not operate the trimmer in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Trimmers create sparks which may ignite the dust or fumes.

If the unit starts unintentionally when the mains plug is connected, disconnect the mains at once. Contact FLYMO to check the unit.

additional handle forwards, snap them into the holder

6. Place both halves of the impeller

7. From the front, push the plant guard

8. Place the protective cover

9. Turn the protective cover

10. Rotate the protective cover

of the trimmer head 7 and close until they

groove

audibly engage [Fig. A4].

of the trimmer head 7. In doing so, ensure

groove

that the installed bow can rotate freely (i. e. insert the bow with the kink pointing upwards) [Fig. A5].

[Fig. A6].

head

the trimmer head entirely.

audibly engages [Fig. A7].

and, with the grooves

on top of the trimmer

until it can be pushed over

anti-clockwise until it

pointing

[Fig. A3].

around the lower

into the upper

DANGER! Risk of physical injury!

Cut injury when the product starts accidentally.

v Before you connect, adjust or transport the

product, disconnect the mains cable and transport the product by the bottom handle.

To connect the trimmer [ Fig. O1 ]:

DANGER! Risk of electric shock! To avoid damage to the mains cable

must be inserted into the cable lock

v Before you operate the product insert the mains

into the cable lock w.

cable

1. Loop the mains cable and pull tight.

lock

2. Connect the mains cable

To set the work positions:

CAUTION! Avoid contact between the ground and the trimmer head in working position 1 + 2.

Work position 1 [Fig. O2]:

For standard trimming.

Work position 2 [Fig. O3/O4]:

Trimming beneath obstacles.

1. Push the foot pedal

into the desired working position.

2. Release the foot pedal

, insert the loop into the cable

into a 230 V mains socket.

and lower the shaft downwards

and allow the shaft to engage.

Work position 3 [ Fig. O5 / O6 ]:

Vertical trimming of overhanging lawn edges.

The upright must be in the uppermost position in working position 3.

1. Turn the plant guard

position until it engages.

2. Push the foot pedal uppermost position.

3. Push the button 0° to 90° until it engages.

4. With the impeller, move the trimmer along the lawn edge.

To set the trimmer to the body height [ Fig. O7 ]:

To set the shaft length:

v Loosen the clamping sleeve

to the desired shaft length and re-tighten the clamping

sleeve

The clamping sleeve t must be fastened firmly enough to prevent the shaft from being moved.

To set the additional handle:

v Pull the lock

set the additional handle release the lock

If the trimmer is correctly set to the body height, the posture is upright and the trimmer head in work position 1 is tilted forwards slightly.

v Hold the trimmer by the handle

handle tilted forwards slightly.

To adjust the plant guard [ Fig. O8 / O9 ]:

Working position [ Fig. O8 ] / Parking position [ Fig. O9 ] v Turn plant guard

position until it locks into place.

in such a manner that the trimmer head is

through 90° into the Parking

and move the upright into the

and rotate the trimmer head from

, extend the handle z

belonging to the additional handle 2,

to the desired incline and

and additional

through 90° into the required

To start the trimmer [ Fig. O1 ]:

DANGER! Risk of physical injury! Risk of injury if the product does not stop

when you release the start button.

v Do not bypass the safety devices or switches.

For example do not attach the start lever the handle.

To start:

The product is fitted with a two-handed safety device (start lever uct from being turned on by accident.

1. Push the safety interlock start lever

2. Release the safety interlock

To stop:

v Release the start lever

To extend the cutting filament (double auto feed system) [ Fig. O10 ]:

A clean cut is achieved only with the maximum filament length.

The cutting filament when the filament cassette comes to a standstill after switch off.

As the filament can only be lengthened in small increments, it can be necessary in some cases to repeat the switch-off / switch-on action several times (up to 6 times). Important is that the filament cassette comes to a complete standstill each time.

The cutting filament has been sufficiently lengthened when, after switch-on, it audibly strikes the filament limiter

The filament cassette has to be replaced when the cutting filament has been used up:

FLYMO Filament Cassette and Cutting Filament:

• 500E FLY021 Part.no.: 513937190

• 580E / 650E FLY061 Part.no.: 510245990

with safety interlock u) to prevent the prod-

with one hand and pull the

with the other hand.

is lengthened automatically

4. MAINTENANCE

DANGER! Risk of physical injury! Cut injury when the product starts

accidentally.

v Before you maintain the product, make sure that

the mains cable is disconnected.

To clean the trimmer [ Fig. M1 / M2 ]:

DANGER! Electric shock! Risk of injury and risk of damage to the

product.

v Do not clean the product with water or with a

water jet (in particular high-pressure water jet).

The airflow slots must always be clean.

1. Clean the airflow slots a screwdriver).

with a soft brush (do not use

2. Clean all movable parts after each operation. Especially remove any grass and dirt from the cover

To pull the cutting filament manually out of the filament cassette [ Fig M3 ]:

A cutting filament that is too short or no longer extends automatically when the trimmer is turned on can be pulled out manually.

1. Push and release manual feed button gently pull on one of the filaments reaches the filament limiter.

2. When the required amount of filament is fed out, gently pull on the second filament (There is no need to push the manual feed button

3. If the filament extends past the filament limiter, too much filament has been fed out. Remove the cassette cover

and click filament cassette anti-clockwise until the fil-

ament is at the desired length.

again).

, while you

until the filament

Always return the product to its normal operating position before you start again.

To replace the filament cassette or the cutting filament:

DANGER! Risk of physical injury! Risk of injury from metal cutting par ts! v Do not use metal cutting parts or replacement

parts and accessories not approved by FLYMO.

Only use original FLYMO Filament Cassettes. You can order Replacement Filament Cassettes from

your FLYMO dealer or directly from the FLYMO Customer Service. You can buy either a Replacement Filament Cassette or the Cutting Filament only.

FLYMO Filament Cassette and Cutting Filament:

• 500E FLY021 Part.no.: 513937190

• 580E / 650E FLY061 Part.no.: 510245990

1. Push and hold the two latches

2. Remove the cassette cover

3. Remove the old filament cassette

4. Remove all dirt in the cassette holder

5. Release one filament filament cassette

6. Secure the filament

into one slot j.

from the cleat © of the new

5. STORAGE

7. Pull approximately 10 cm of the filament filament cassette

holder

8. Repeat for the second filament.

9. Put the filament cassette

10. Check that the filament cassette

To replace the cutting filament [ Fig. M3/M5] :

1. Remove the filament cassette

2. Remove all dirt in the cassette holder

3. Take approximately 5 meters of one filament

4. Wind the filament

5. Repeat for the second filament.

6. Replace the filament cassette

Make sure, the filament is not caught and the latches are locked.

locked. (Try to remove the filament cassette without to push the latches

insert it into one of the filament lock holes filament cassette

the direction of the arrows on the top of the filament cassette

of the filament cassette

Make sure, the filament filament cassette

through the slot j in the cassette

into the cassette holder h.

onto the filament cassette g in

. (Wind the first filament on the upper section

is neatly winded on the

out of the

is correctly

in the

and

To put into storage [ Fig. S1 ]:

The product must be stowed away from children.

1. Disconnect the mains cable.

2. Clean the product.

3. Wind the cable around the cable hook

4. Stow the product in a dry area where it has protection

Recommendation:

The product can be hung up by the handle. The cutting head is not put under too much strain if the product is stowed hanging up.

. (To unwind the cable push the button ö and

pedal

turn the cable hook

from frost.

down.)

and the foot

Disposal:

(in accordance with RL2012/19/EC)

The product must not be added to usual household waste. Refer to local environmental laws for discarding.

v Important: Make sure that the product is discarded

through your municipal recycling collection centre.

6. TROUBLESHOOTING

DANGER! Risk of physical injury! Cut injury when the product starts

accidentally.

v Before you troubleshoot the product, make sure

that the mains cable is disconnected.

Problem Possible Causes Remedy

Filament is to short or trimmer vibrates

Filament not fed out and visible. v Pull the filament until it reaches the

filament limiter

Filament not removed from the cleat. v Remove the filament from the cleat.

Problem Possible Causes Remedy

Filament is to short or trimmer vibrates

Filament is jammed on the filament cassette.

v Rewind the filament to remove

crossed loops. Check that the filament is neatly winded. If it does not help change the filament cassette.

Filament is broken inside the filament

v Replace the cutting filament.

cassette.

Continuous clattering noise Motor has not reached full speed

before use.

v Allow the motor to reach full speed

before use.

Too much filament has been fed out. v Rewind the filament.

Filament limiter is missing. v Contact your local approved

Service Center or Husqvarna UK Ltd. Customer Service.

Filament snaps continuously You do not use the correct working

v Use the correct working position.

position.

Filament is jammed on the filament cassette.

v Rewind the filament to remove

crossed loops. Check that the filament is neatly winded. If it does not help change the filament cassette.

Poor performance The cassette holder is dirty. v Clean the cassette holder.

For any other malfunctions please contact the Husqvarna UK Ltd. Customer Service. Repairs must only be done by Husqvarna UK Ltd. service departments or specialist dealers approved by FLYMO.

7. TECHNICAL DATA

Unit Value (CTE25) Value (CTE27) Value (CTE30)

Motor power consumption W 500 580 650

Mains voltage V 230 230 230

Mains frequency Hz 50 50 50

Cutting filament thickness mm 1.5 2.0 2.0

Cutting width cm 25 27 30

Cutting filament supply m 5 5 5

Cutting filament feed Manual filament feed

system

Speed of cutting filament rpm 11,500 9,800 8,500

Weight kg 3.1 3.2 3.4

Sound pressure level L Uncertainty k

Sound power level L measured / guaranteed Uncertainty k

Hand / arm vibration a Uncertainty k

Measuring process complying with: 1) EN 50636-2-91 2) RL 2000/14/EC

vhw

80.4

dB(A)

2.5

dB(A) 92 / 96

X.X

2.0

m/s

1.5

The stated vibration emission value has been measured according to a standardized test

pro cedure and can be used for comparison of one electric power tool with another. It can also be used for preliminary evaluation of exposure. The vibration emission value can vary during actual use of the electric power tool.

Manual filament feed system

79.3

2.5

91 / 96 X.X

3.6

1.5

Manual filament feed system

80.1

2.5

90 / 96 X.X

3.0

1.5

8. ACCESSORIES

FLYMO Filament Cassette and Cutting Filament 500E FLY021 Part.no.: 513937190

FLYMO Filament Cassette and Cutting Filament 580E / 650E FLY061 Part.no.: 510245990

9. Service / Warranty

Service:

Please contact the address on the back page.

Warranty:

In the event of a warranty claim, no charge is levied to you for the services provided.

Husqvarna UK Ltd. offers a two-year warranty (effective as of the date of purchase) for this product. This warranty includes all significant defects of the product that can be proved to be material or manufacturing faults. This warranty is fulfilled by supplying a fully functional replacement product or by repairing the faulty product sent to us free of charge; we reserve the right to choose between these options. This service is subject to the following provisions:

• The product was used for its intended purpose as per the recommendations in the operating instructions.

• Neither the purchaser nor a third party has attempted to repair the product.

This manufacturer’s warranty does not affect warranty entitlements against the dealer / retailer.

If problems arise with this product, please contact our Service department or send the defective product along with a brief description of the fault to Husqvarna UK Ltd., making sure to have sufficiently covered any shipping costs and to have followed the relevant postage and packaging guidelines. A warranty claim must be accompanied by a copy of the proof of purchase.

Consumables:

The cutting filament and the filament cassette are con sumables and are not included in the guarantee.

Product liability

In accordance with the German Product Liability Act, we hereby expressly declare that we accept no liability for damage incurred from our products where said products

have not been properly repaired by a FLYMO-approved service partner or where original FLYMO parts or parts authorised by FLYMO were not used.

EC Declaration of Conformity

The undersigned, Husqvarna AB, 561 82 Huskvarna, Sweden, hereby certifies that, when leaving our factory, the products indicated below are in accordance with

Description of the product: Turbotrimmer

Product type Contour 500E; 580E; 650E

Article-Number CTE25; CTE27; CTE30

CE-Directives 2006/42/EC

Harmonized EN EN 60335-1

Deposited Documentation GARDENA Technical Documentation,

Conformity Assessment according to 2000/14/EC Procedure: ar t. 14 Annex VI

Noise level: measured / guaranteed CTE25 92 dB(A) / 96 dB(A)

Year of CE marking 2017

Ulm xx.xx.2017

Authorized representative: XXXX

the harmonised EU guidelines, EU standards of safety and product specific standards. This certificate becomes void if the products are modified without our approval.

2014/30/EC 2000/14/EC 2011/65/EC

EN 50636-2-91 EN ISO 12100

M. Kugler, 89079 Ulm

CTE27 91 dB(A) / 96 dB(A) CTE30 90 dB(A) / 96 dB(A)

Deutschland /Germany

GARDENA Manufacturing GmbH Central Service

Lorenser-Straße 40

Hans

89079 Ulm

D Produktfragen: (+49) 731 490 Reparaturen: (+49) 731 490 service

Albania

COBALT Sh.p.k. Rr. Siri Kodra 1000 Tirana

Argentina

Husqvarna Argentina S.A. Av.del Libertador 5954 Piso 11–Torre B (C1428ARP) Buenos Aires Phone: (+54) 11 5194 5000 info.gardena ar.husqvarna.com

Armenia

Garden Land Ltd. 61 Tigran Mets 0005 Yerevan

Australia

Husqvarna Australia Pty. Ltd. Locked Bag 5 Central Coast BC NSW 2252 Phone: (+61) (0) 2 43527400 customer.service husqvarna.com.au

Austria /Österreich

Husqvarna Austria GmbH Industriezeile 36 4010 Linz Tel.: (+43) 732 77 0101 service.gardena husqvarnagroup.com

Azerbaijan

Firm Progress a. Aliyev Str. 26A 1052 Baku

Belgium

Husqvarna België nv/ sa Gardena Division Rue Egide Van Ophem 111 1180 Uccle / Ukkel Tel.: (+32) 2 72092 12 info

Bosnia / Herzegovina

SILK TRADE d.o.o. Industrijska zona Bukva bb 74260 Tešanj

Brazil

Husqvarna do Brasil Ltda Av. Francisco Matarazzo, 1400 São Paulo CEP: 05001 Tel: 0800 marketing.br.husqvarna husqvarna.com.br

Bulgaria

AGROLAND България АД бул. 8 Декември, №13 Офис 5 1700 Студентски град София Тел.: (+ 359) 2466 6910 info

Canada /USA

GARDENA Canada Ltd. 100 Summerlea Road Brampton, Ontario L6T 4X3 Phone: (+1) 905 792 9330 info

Chile

Maquinarias Agroforestales Ltda. (Maga Ltda.) Santiago, Chile Avda. Chesterton # 8355 comuna Las Condes Phone: (+56) 2 202 4417 Dalton Zipcode: 7560330

123

290

gardena.com

gardena.be

–

19º andar

–

903

112252

agroland.eu

gardenacanada.com

maga.cl

–

485

Our polic y of continuous impr ovement m eans tha t the specificat ion of pro ducts may be alter ed from time to time wi thout pr ior notice.

China

Husqvarna (Shanghai) Management Co., Ltd.

富世华（上海）管理有限公司

3F, Benq Square B, No207, Song Hong Rd., Chang Ning District, Shanghai, PRC. 200335

上海市长宁区淞虹路207号明基广场B座3楼，邮编：200335

Colombia

Husqvarna Colombia S.A. Calle 18 No. 68 D Industrial de Montevideo Bogotá, Cundinamarca Tel. 571 2922700 ext. 105 jairo.salazar husqvarna.com.co

Costa Rica

Compania Exim Euroiberoamericana S.A. Los Colegios, Moravia, 200 metros al Sur delColegio Saint Francis Phone: (+506) 297 68 83 exim_euro

Croatia

Husqvarna Austria GmbH Industriezeile 36 4010 Linz Tel.: (+43) 732 77 0101 service.gardena husqvarnagroup.com

Cyprus

Med Marketing 17 Digeni Akrita Ave P.O. Box 27017 1641 Nicosia

Czech Republic

Husqvarna Česko s.r.o. Türkova 2319/ 5b 149 00 Praha 4 – Chodov Bezplatná infolinka: 800 100425

servis

Denmark

GARDENA DANMARK Lejrvej 19, st. 3500 Værløse Tlf.: (+45) 70 264770 husqvarna www.gardena.com/ dk

Dominican Republic

BOSQUESA, S.R.L Carretera Santiago Licey Km. 5 ½ Esquina Copal II. Santiago Dominican Republic Phone: (+809 ) 736-0333 joserbosquesa

Ecuador

Husqvarna Ecuador S.A. Arupos E1-181 y 10 de Agosto Tel. (+593) 22800739 francisco.jacome husqvarna.com.ec

Estonia

Husqvarna Eesti OÜ Valdeku 132 EE-11216 Tallinn info

Finland

Oy Husqvarna Ab Gardena Division Lautatarhankatu 8 B/ PL 3 00581 HELSINKI www.gardena.fi

France

Husqvarna France 9/ 11 Allée des pierresmayettes 92635 Gennevilliers Cedex France http: //www.gardena.com/ fr N° AZUR: 0 81000 78 23 (Prix d’un appel local)

Flymo

31, zona

–

San José

racsa.co.cr

cz.husqvarna.com

husqvarna.dk

claro.net.do

Quito, Pichincha

gardena.ee

and other p roduct and featu re names ar e registered or unregistere d tradema rks of F lymo S. A.

Georgia

Transporter LLC 8/ 57 Beliashvili street 0159 Tbilisi, Georgia Phone: (+995) 322 14 71 71

Great Britain

Husqvarna UK Ltd Preston Road Aycliffe Industrial Park Newton Aycliffe County Durham DL5 6UP info.gardena husqvarna.co.uk

Greece

Π.ΠΑΠΑΔΟΠΟΥΛΟΣ ΑΕΒΕ Λεωφ. Αθηνών 92 Αθήνα Τ.Κ.104 42 Ελλάδα Τηλ. (+30) 210 5193100

papadopoulos.com.gr

info

Hungary

Husqvarna Magyarország Kft. Ezred u. 1 1044 Budapest Telefon: (+36) 1 251 vevoszolgalat.husqvarna husqvarna.hu

Iceland

Ó. Johnson & Kaaber

485

Tunguhalsi 1 110 Reykjavik

ojk.is

ooj

Ireland

Husqvarna UK Ltd Preston Road Aycliffe Industrial Park Newton Aycliffe County Durham DL5 6UP info.gardena husqvarna.co.uk

Italy

Husqvarna Italia S.p.A. Via Santa Vecchia 15 23868 VALMADRERA (LC) Phone: (+39) 0341.203.111 assistenza.italia it.husqvarna.com

Japan

KAKUICHI Co. Ltd. Sumitomo Realty & Development Kojimachi BLDG., 8F

1 Nibanncyo

Chiyoda Tokyo 102 Phone: (+81) 33 264 4721 m_ishihara

Kazakhstan

LAMED Ltd. 155/ 1, Tazhibayevoi Str. 050060 Almaty IP Schmidt Abayavenue 3B 110 005 Kostanay

Korea

Kyung Jin Trading CO.,LTD. 107-4, SunDuk Bld., YangJae-dong, Seocho-gu, Seoul, (zipcode: 137-891) Phone: (+82) (0)2 574-6300

Kyrgyzstan

Alye Maki av. Moladaya Guardir J 3 720014 Bishkek

Latvia

Husqvarna Latvija SIA Ulbrokas 19A

LV-1021 Rīga

gardena.lv

info

Lithuania

UAB Husqvarna Lietuva Ateities pl. 77C

52104 Kaunas

gardena.lt

info

0084

kaku-ichi.co.jp

Luxembourg

Magasins Jules Neuberg 39, rue Jacques Stas Luxembourg Case Postale No. 12 Luxembourg 2010 Phone: (+352) 40 14 01 api

Mexico

AFOSA Av. Lopez Mateos Sur # 5019 Col. La Calma 45070 Zapopan, Jalisco Mexico Phone: (+52) 33 3 818 icornejo

Moldova

Convel S.R.L. 290A Muncesti Str. 2002 Chisinau

Netherlands

Husqvarna Nederland B.V. GARDENA Division Postbus 50131 1305 AC ALMERE Phone: (+31) 36 521 00 10

4161

info

Neth. Antilles

Jonka Enterprises N.V. Sta. Rosa Weg 196 P.O. Box 8200 Curaçao Phone: (+599) 9 767 6655 pgm

New Zealand

Husqvarna New Zealand Ltd. PO Box 76 Manukau City 2241 Phone: (+64) (0) 9 9202410 support.nz

Norway

Husqvarna Norge AS Gardena Division Trøskenveien 36 1708 Sarpsborg info

Peru

Husqvarna Perú S.A. Jr. Ramón Cárcamo 710 Lima 1 Tel : (+ 51)1 3320400 ext. 416 juan.remuzgo husqvarna.com

Poland

Husqvarna Poland Spółka z o.o. ul. Wysockiego 15 b 03 Phone: (+ 48) 22330 9600 gardena

Portugal

Husqvarna Portugal, SA Lagoa 2635 Tel.: (+351) 21 922 85 30 Fax : (+351) 21 922 85 36 info

Romania

Madex International Srl Soseaua Odaii 117 RO 013603 Bucure Phone: (+ 40) 21 352.76.03

madex

Russia /Россия

ООО „Хускварна“ 141400, Московская обл., г. Химки, улица Ленинградская, владение 39, стр.6 Бизнес Центр „Химки Бизнес Парк“, помещение ОВ02_04 http://www.gardena.ru

Serbia

Domel d.o.o. Autoput za Novi Sad bb

11273 Belgrade Phone: (+381) 118 4888 12 miroslav.jejina

Gasperich 2549

neuberg.lu

afosa.com.mx

gardena.nl

jonka.com

437

husqvarna.co.nz

gardena.no

371 Warszawa

husqvarna.com.pl

Albarraque

595 Rio de Mouro

gardena.pt

ines.ro

123,

ti, S1

domel.rs

Singapore

Hy-Ray PRIVATE LIMITED 40 Jalan Pemimpin #02

08 Tat Ann Building Singapore 577185 Phone: (+65) 6253 2277 shiying

Slovak Republic

Husqvarna Česko s.r.o. Türkova 2319/ 5b 149 00 Praha 4 – Chodov Bezplatná infolinka: 800 154044

servis

3434

sk.husqvarna.com

Slovenia

Husqvarna Austria GmbH Industriezeile 36 4010 Linz Tel.: (+43) 732 77 0101 service.gardena husqvarnagroup.com

South Africa

Husqvarna South Africa (Pty) Ltd Postnet Suite 250 Private Bag X6, Cascades, 3202 South Africa Phone: (+27) 33 846 9700 info

gardena.co.za

Spain

Husqvarna España S.A. Calle de Rivas nº10 28052 Madrid Phone: (+34) 91 708 0500 atencioncliente

Suriname

Agrofix n.v. Verlengde Hogestraat #22 Phone: (+ 597) 472426 agrofix

Pobox : 2006 Paramaribo Suriname

Sweden

Husqvarna AB Gardena Division S

561 82 Huskvarna

gardenaorder

Switzerland /Schweiz

Husqvarna Schweiz AG Consumer Products Industriestrasse 10 5506 Mägenwil Phone: (+41) (0) 62 88737 90 info

gardena.ch

Turkey

Dost Bahçe Dış Ticaret Mümessillik A.Ş Yunus Mah. Adil Sok. No:3 Ic Kapi No: 1 Kartal 34873 Istanbul

Phone: (+90) 216 38 93939 info

dostbahce.com.tr

Ukraine /Україна

ТОВ «Хускварна Україна» вул. Васильківська, 34, офіс 204 03022, м. Київ Тел. (+38) 044 498 39 02

info

gardena.ua

Uruguay

FELI SA Entre Ríos 1083 CP 11800 Montevideo Tel: (+598) 22 0318 44 info

felisa.com.uy

Venezuela

orporación Casa y Jardín C.A. Av. Caroní, Edif. Trezmen, PB. Colinas de Bello Monte. 1050 Caracas. Tlf: (+ 58) 212 992 33 22 info

casayjardin.net.ve

C500E-20.960.01/0217

0000

20.960.08 /0618

GARDENA

Husqvarna AB

Manufacturing GmbH

S-561 82 Huskvarna

D- 89070 Ulm http: //www.gardena.com

Sweden

hyray.com.sg

gardena.es

sr.net

–

South America

husqvarna.se

–

Uruguay

485

Flymo Contour 650E, Contour 500E, Contour 580E Operation Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual