®
If any part is found to be defective due to faulty manufacture within
the guarantee period, Husqvarna Australia PTY/Husqvarna New
Zealand Ltd., through its Authorised Service Repairers will effect the
repair or replacement to the customer free of charge providing:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty adjustment by
the user.
(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired, taken apart or
tampered with by any person not authorised by Husqvarna Australia
PTY/Husqvarna New Zealand Ltd.
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used commercially.
* This guarantee is additional to, and in no way diminishes the
customers statutory rights.
Failures due to the following are not covered, therefore it is important
that you read the instructions contained in this Operator’s Manual and
understand how to operate and maintain your machine:
Failures not covered by guarantee
* Replacing Nylon Line.
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in accordance with the
instructions and recommendations contained in this Operator‘s
Manual.
* Machines used for hire are not covered by this guarantee.
* The following items listed are considered as wearing parts and their
life is dependent on regular maintenance and are, therefore not
normally subject to a valid warranty claim: Nylon Line, Spool and
Line, Electric Mains Cable
* Caution!
Husqvarna Australia PTY/Husqvarna New Zealand Ltd. does not
accept liability under the warranty for defects caused in whole
or part, directly or indirectly by the fitting of replacement parts or
additional parts that are not either manufactured or approved by
Husqvarna Australia PTY/Husqvarna New Zealand Ltd., or by the
machine having been modified in any way.
Guarantee & Guarantee Policy
Original Instructions
5857342-02 06/2015
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
Copyright © 2015 Flymo S.A. All rights reserved. Flymo
®
and other product and feature names are registered or
unregistered trademarks of Flymo S.A.
Technical data
IMPORTANT INFORMATION
Read before use
& retain for future reference
Contour
500E/580E/650E
• Awareness of the environment must be considered when disposing
of ‘end-of-life’ product.
• If necessary, contact your local authority for disposal information.
The symbol
on the product or on its packaging indicates that
this product may not be treated as household waste. Instead it shall
be handed over to the applicable collection point for the recycling of
electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste
handling of this product.
For more detailed information about recycling of this product, please
contact your local council office, your household waste disposal service
or the shop where you purchased the product.
Environmental Information
Husqvarna AB
S-561 82 Huskvarna
Sweden
Replacement Parts
Spool and Line
Reference: 500E FLY021
580E 650E FLY061
Part no.: 513937190
Part no.: 510245990
1
Carton Contents
IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product.
IF ANY PARTS ARE MISSING CONTACT:-
Husqvarna Australia PTY. Ltd., Customer Service Department direct, Telephone: 024352 7400
Husqvarna New Zealand Ltd., Customer Service Department direct, Telephone: 99202410
Safety
General
1. This product is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
the use of the product by a person responsible for their
safety. Children should be supervised to ensure that they
do not play with the product. Local regulations may restrict
the age of the operator.
2. Never allow children or people unfamiliar with the
instructions to use the machine.
3. Stop using the machine while people, especially children,
or pets are nearby.
4. Only use the trimmer in the manner and for the functions
described in these instructions.
5. Never operate the trimmer when you are tired, ill or under
the influence of alcohol, drugs or medicine.
6. The operator or user is responsible for accidents or
hazards occurring to other people or their property.
Electrical
AVOID ACCIDENTAL STARTING. REMOVE PLUG FROM
MAINS AND KEEP FEET AWAY FROM THE SWITCH
LEVER WHEN:- CLEANING AROUND THE INSIDE OF
THE SAFETY GUARD, REMOVING OR REFITTING SPOOL
CAP, MANUALLY FEEDING OR REPLACING NYLON
LINE.
1. We recommend the use of a Residual Current Device
(R.C.D.) with a tripping current of not more than 30mA.
Even with a R.C.D. installed 100% safety cannot be
guaranteed and safe working practice must be followed at
all times. Check your R.C.D . every time you use it.
2. Before use, examine cable for damage. If the cable is
found to be defective, take the product to an Authorised
Service Centre and have the cable replaced.
3. Do not use the trimmer if the electric cables are damaged
or worn.
4. Immediately disconnect from the mains electricity supply
if the cable is cut, or the insulation is damaged. Do not
touch the electric cable until the electrical supply has been
disconnected. Do not repair a cut or damaged cable.
Replace it with a new one.
5. Your extension cable must be uncoiled, coiled cables can
overheat and reduce the efficiency of your trimmer.
6. Keep the cable clear of the cutting area and obstacles at
all times.
7. Do not pull cable around sharp objects.
8. Always switch off at the mains before disconnecting any
plug, cable connector or extension cable.
9. Never pull on the cable to disconnect any of the plugs.
10. Switch off, remove plug from mains and examine electric
supply cable for damage or ageing before winding cable
for storage. Do not repair a damaged cable, replace it with
WARNING. When using the product the safety rules must be followed. For your own safety and that of bystanders
please read these instructions before operating the product. Please keep the instructions safe for later use.
Explanation of Symbols on the product
360º
10m
12m Electric Cable
with moulded on plug
Instruction Manual
Guard
2
a new one. Use only Flymo replacement cable.
11. Always wind cable carefully, avoiding kinking.
12. Never carry the product by the cable.
13. Use only on AC mains supply voltage shown on the
product rating label.
14. Our products are double insulated to EN60335.
Under no circumstance should an earth be connected to
any part of the trimmer.
Preparation
1. While using your product always wear eye protection,
substantial footwear and long trousers. Do not operate the
equipment when barefoot or wearing open sandals.
2. Before using the machine and after any impact, check for
signs of wear or damage and repair as necessary.
3. Inspect the area to be cut before each use. Remove all
objects such as stones, broken glass, nails, wire, string
etc, which can be thrown or become entangled in the
trimmer head.
4 .
Before use, inspect the area for wildlife, especially hedgehogs.
5. Check that the cutting head is fitted correctly.
Use
1. Use the trimmer only in daylight or good artificial light.
2. Avoid operating your trimmer in wet grass, where feasible.
3. Take care in wet grass, you may lose your footing.
4. On slopes, be extra careful of your footing and wear
non-slip footwear.
5. Do not walk backwards when trimming, you could trip.
Walk never run.
6. Keep cutting head below waist level.
7. Switch off before pushing the trimmer over surfaces other
than grass.
8. Never operate the trimmer with damaged guards or
without guards in place.
9. Never fit metal cutting elements.
10. Keep hands and feet away from the cutting means at all
times and especially when switching on the motor.
11. Never pick up or carry a trimmer by the cable.
12. Do not lean over the trimmer guard - objects may be
thrown by the cutting line.
13. Beware of cut-off pieces of nylon line ejected during use.
14. Remove the plug from the mains :
- before leaving the trimmer unattended for any period;
- before clearing a blockage;
- before checking, cleaning or working on the appliance;
- if you hit an object. Do not use your trimmer until you are
sure that the entire trimmer is in a safe operating condition;
- if the trimmer starts to vibrate abnormally. Check
immediately. Excessive vibration can cause injury.
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be sure the
trimmer is in safe working condition.
2. Replace worn or damaged parts for safety.
3. Only use the replacement cutting line specified for this
product.
4. Only use replacement parts and accessories
recommended by Husqvarna Australia PTY/Husqvarna
New Zealand Ltd.
5. After any maintenance in dealing with the cutting line,
always return the product to its normal operating position
before switching on.
6. Clean unit with a dry cloth. Never use metal objects to
clean the unit.
7. Inspect and maintain the trimmer regularly. Any repairs
must be carried out by an authorised repairer.
8. Store in a cool dry place and out of reach of children.
Do not store outdoors.
9. Allow the product to cool for at least 30 minutes before
storing.
Cables
IMPORTANT If you want to use an extension cable when
operating your product, only the following cable dimensions
should be used.
- 1.0 mm
2
: max length 40 m
- 1.5 mm
2
: max length 60 m
- 2.5 mm
2
: max length 100 m
Minimum rating :
1.00 mm
2
size cable, 10 amps 250 volts AC.
1. YOUR PRODUCT IS SUPPLIED WITH AN ELECTRIC
MAINS CABLE WIRED DIRECTLY INTO THE
PRODUCT.
1. If the supply cord is damaged, it must be replaced by
your local Husqvarna Approved Service Centre or similarly
qualified persons in order to avoid a hazard.
2. Flymo Extension Cables are available from your local
Husqvarna Approved Service Centre.
3. Do not wire an extension cable directly to your product
yourself. Please contact your local Husqvarna Approved
Service Centre for further information on the connectors
and kits available.
4. Only use extension cables specifically designed for
outdoor use and which conform to one of the following
specifications: Ordinary rubber (60245 IEC 53), Ordinary
PVC (60227 IEC 53) or Ordinary PCP (60245 IEC 57)
CONNECTORS Flymo connectors are suitable for use
with 2 core cable only. Under no circumstances should
these connectors be used for earthed products. All Flymo
connectors and cables are of splashproof construction. They
are not waterproof and must not be left outside permanently
nor should they be submerged or immersed in water. Do not
let cable lay or trail through pools of water or splashed with
water from hose pipes.
MAINS PLUG REPLACEMENT
• If the plug supplied is cut off it should be destroyed.
There is an electric shock hazard if a cut off plug is
inserted into a 13 amp socket.
1. No earth required. Flymo products are double insulated to
EN60335 and under no circumstances should an earth be
connected to any part of the product.
2. Ensure the mains voltage suits your product.
3. IMPORTANT!
The wires in the mains lead are coloured in accordance with
the following code:
BLUE - NEUTRAL BROWN - LIVE
The wire which is coloured BLUE must be connected to the
Terminal which is marked with the letter ‘N’ or coloured BLACK.
The wire which is coloured BROWN must be connected to the
Terminal which is marked with the letter ‘L’ or coloured RED.
4. It is important that the outer sheath is clamped correctly into
the 3-pin plug.
5. If in doubt consult your local Service Repairer or qualified
electrician before the machine is used.
6. A 13 Amp fuse must be fitted to the Mains Plug.
7. The normal plug fuse and household fuse only protect
the electrical equipment and are not a safeguard against
electrocution.
If your product is hard wired i.e. non-detachable mains
electric cable, a conversion kit and extension cable is
available from all Approved Service Centres which can be
found in your local Yellow Pages.
Wheel
Trimmer Head
Assembly Instructions
A1 A2
Assembly of Switch Handle to Tube (A1)
• Ensure that the internal cable is not twisted.
1. Insert the tube into the switch handle.
2. Push until it clicks into position.
• ENSURE THAT THE TUBE IS FULLY LOCATED BY
ATTEMPTING TO REMOVE IT.
Assembly of Trimmer Head to Tube (A2)
• Ensure that the internal cable is not twisted.
1. Insert the tube into the trimmer head.
2. Push until it clicks into position.
• ENSURE THAT THE TUBE IS FULLY LOCATED BY
ATTEMPTING TO REMOVE IT.
Plant Guard
CLICK!
CLICK!
Steady Handle
Warning
Read the user instructions carefully to make sure
youunderstand all the controls and what they do.
Keep bystanders away. Do not operate whilst
people especially children or pets are in the
area.
Wear eye protection
Do not operate in the rain or leave the product
outdoors while it is raining.
Switch off! Remove plug from mains before
adjusting, cleaning or if cable is entangled or
damaged.
Warning: The cutting line continues to rotate after the
machine has been switched off.
Type CTE25 CTE27 CTE30
Width of Cut (cm) 25 27 30
Speed of Rotation of Cutting Device (rpm) 11,500 9,800 8,500
Measured Sound Power L
WA
(dB(A)) 92 91 90
Guaranteed Sound Power L
WA
(dB(A)) 96 96 96
Sound pressure L
pA
(dB(A)) 80.3 79.3 80.1
Uncertainty K
pA
(dB(A)) 2.5 2.5 2.5
Hand / arm vibration a
h
(m/s2) 2.0 3.6 3.0
Uncertainty K
ah
(m/s2) 1.5 1.5 1.5
Weight (kg) 3.1 3.2 3.4
Safety Lock-off Switch
Upper Shaft
Lower Shaft
Switch lever
5857342-02 Contour 500E-580E-650E AU/NZ.indd 1 14.06.15 11:25
3
Assembly Instructions cont’
C2
E
C1
D
B1
B3
B2
B4
4
Double Auto Feed System
• WARNING
• The use of eye protection is recommended.
Do not lean over the trimmer whilst trimming or edging,
objects may be thrown by the cutting line.
Do not allow cutting head to rest on the ground.
Do not overload your trimmer.
Overloading can be avoided by making sure the motor
speed does not drop unduly.
Disconnect from the mains electricity supply before
attempting any maintenance or adjustment.
• BEFORE USE
• Make sure that both lines are fed out.
• Make sure motor is up to full speed before trimming or
edging.
How to trim
PRODUCTS 580E & 650E CONTAIN AN AUTOMATIC
ELECTRONIC SENSOR WHICH INCREASE THE SPEED
OF THE MOTOR AS THE LOAD INCREASES (i.e. CUTTING
GRASS).
UNDER LIGHTER LOAD CONDITIONS OR NO LOAD THE
SPEED DECREASES AUTOMATICALLY.
THIS WILL OPTIMISE THE CUTTING SPEED IN ALL
CONDITIONS AND ENSURES THE CORRECT SPEED FOR
EACH TYPE OF GRASS.
1. Hold as illustrated in fig. H.
2. To start, squeeze the safety lock off (H1) and then the switch
lever (H2).
3. Cut with nylon line at an angle using the tip. See fig. J1.
4. Swing trimmer in and out of the cutting area taking small
cuts (J2).
5. Line is fed out automatically every time the trimmer head
stops rotating and returns to operating speed.
• Extra line can be fed out manually as described in Manual
line feed
6. To stop your trimmer release the switch lever.
Using the Plant & Tree Guard
The Plant and Tree guard allows the trimming of grass close to
plants and trees without damaging them with the cutting line.
1. Rotate the guard into it’s forward position as illustrated in K1.
2. Uste the trimmer around trees (K2) and near plants.
How to edge
1. Ensure the plant guard is in the PARK position.
2. To convert to edging mode, press button (L1) and
twist head (L2). An audible “click” will confirm that the
head is locked.
3. Hold as illustrated in Fig H.
4. To start, squeeze the safety lock-off (H1) and then the
switch lever (H2).
5. Rest edger on wheel for extra stability and line up the
edge of the lawn. Edge in direction indicated in Fig M.
6. To stop your trimmer release the switch lever.
7. To return to trimming mode, press button and twist
head back the opposite way. An audible “click” will
confirm that the head is locked.
• When edging, ensure that the edging wheel is
always resting on the grass (and not on the path/
driveway).
Using the Shrubbing position
1. By pressing the lever (N1) with your foot, the handle can be
lowered into three different positions to enable the use of the
product under shrubs and low obstacles (P).
J1
L
H
J2
How to use
How the automatic line feed works (G)
1. When initially switching on the trimmer, a small length of line
is fed out.
2. A ‘clattering’ noise will be heard when the two nylon lines hit
the line cutter. DO NOT BE ALARMED this is quite normal.
After approximately 5 seconds the line will be cut to the
correct length and the noise will reduce as the motor reaches
full speed.
• Make sure the motor is up to full speed before trimming
or edging.
3. If the noise of the nylon line being cut cannot be heard, more
line will need to be fed out.
4. To feed more line, it is first necessary to to allow the motor
to stop completely, then re-start, allowing the motor to reach
full speed.
5. Repeat step 4. until you hear the lines hitting against the
cutter. (Do not repeat this procedure more than 6 times)
6. If problems are experienced with the automatic line feed refer
to Fault Finding Chart.
G
line cutter
To manually feed the nylon line (Q)
1. If required line can be fed out manually.
2. To operate, press and release manual line feed button, whilst
gently pulling on one of the lines until the line reaches the
line cutter.
3. When the required amount of line is fed out, gently pull on
the second line (there is no need to press the manual line
feed button again).
4. If the line extends past the line cutter, too much line has
been fed out.
5. If too much line is fed out, remove the spool cap and click
spool anti-clockwise until the line is at the desired length.
• Always return the product to its normal operating
position before switching on.
Manual line feed
To remove spool cap
1. Press and hold in the two cap release latches. (R).
2. Pull cap away from the spoolholder. (R).
When refitting the spool cap
1. Keep all areas of the cap and spoolholder clean. Failure to
do so may prevent the cap being securely located in the
spoolholder.
2. Replace the cap, pressing firmly DOWN towards the
spoolholder to ensure cap is fully located.
3. Check that the cap is correctly fitted by trying to remove it
without depressing the two latches.
To replace nylon line.
For your convenience it is recommended you buy spool and
line complete. Nylon line only is also available.
Both are available from Husqvarna Australia PTY/
Husqvarna New Zealand Ltd. stockists.
To fit spool and line complete:
1. Remove the cap.
2. Remove old spool.
3. Place spool into spoolholder.
4. Release one line from cleat (T1).
5. Secure line into slot (S1).
6. Repeat for second line.
• Ensure spool is fully located by gently rotating it during
fitment, whilst keeping the spoolholder steady.
7. Refit the cap.
To fit nylon line only:
• Remember! Your Flymo Trimmer 500 E is designed
to use only nylon line with a diameter of 1.5 mm,
Trimmer 580 E and 650 E are designed to use nylon
line with a diameter of 2.0 mm.
Use only genuine Flymo nylon line.
1. IMPORTANT - Always wind the line onto the upper
section of the spool first.
Take approximately 5 metres of line. Insert 15 mm of line
into one of the holes in the upper section of the spool (T)
and wind line in the direction of the arrows on the top of the
spool. Leave approximately 100mm of line unwound and
place into cleat as illustrated in figure T1. Repeat on lower
section of spool.
2. Care should be taken to ensure that the line is neatly coiled
on the spool. Failure to do so will impair the efficiency of the
automatic line feed.
3. Then fit spool as described in ‘To fit spool and line
complete’, section above.
Always return the product to its normal operating
position before switching on.
Q
manual line
feed button
Y
Cap
Cap release
latch
Spool
Spoolholder
Slot
R
S
T
Cleat
1
M
Maintenance
W
V
Caring for your product
After you have finished using your product follow the procedure
below:
AVOID ACCIDENTAL STARTING. REMOVE PLUG FROM
MAINS AND KEEP FEET AWAY FROM THE SWITCH
LEVER WHEN: CLEANING AROUND THE INSIDE OF THE
SAFETY GUARD, REMOVING OR REFITTING SPOOL CAP,
MANUALLY FEEDING OR REPLACING NYLON LINE.
1. Disconnect from the mains electricity supply.
2. Never clean your trimmer with water, cleaning fluids, or
solvents, just remove debris with a suitable tool, a soft brush
or dry cloth.
3. Using a soft brush, clean around the inside of the safety
guard, the cutting head (V) and the motor housing air vents.
(W).
4. Remove the wheel by pressing one of the buttons. Clean the
wheel and groove on trimmer head with a soft brush (X & Y).
5. Attach wheel as described in Wheel Assembly.
6. Inspect the trimmer carefully, especially the parts of the
cutting head.
7. If your trimmer is damaged in any way contact your local
approved service centre.
• Never use a damaged trimmer.
8. Store in a cool, dry place and out of reach of children.
Cable Storage
1. Your mains cable can be stored on the product as illustrated
in fig. Z1.
2. Wind cable carefully to avoid kinking.
3. To release the cable press the button and the hook will drop
down (Z2).
4. Push cable hook fully back into position.
T1
Fault Finding Chart
WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment.
FAULT CHECK ACTION
Is the automatic line feed
working?
Manually feed out line.
SEE “MANUAL LINE FEED”
Is the line fed out and visible?
Has line been removed from
cleat?
Remove cap and spool, free line
and re-fit spool and cap. SEE
“CUTTING HEAD”
The line may be jammed on the
spool. Rewind line to remove
crossed loops. Check that line is
in correct section of spool.
Is the manual line feed working?
Has too much line been fed out? SEE “MANUAL LINE FEED”
Contact your local approved
Service Centre.
Is the line cutter missing from
the safety guard?
No
No
No
Yes
Yes
LINE NOT FEEDING
OR
LINE TOO SHORT
OR
TRIMMER VIBRATES
CONTINUOUS
CLATTERING NOISE
LINE SNAPS
CONTINUOUSLY
Contact Husqvarna Australia PTY. Ltd, Customer Service Department direct,
Telephone: 024352 7400
Husqvarna New Zealand Ltd., Customer Service Department direct,
Telephone: 9920 2410
IF NONE OF THE ABOVE
OR IF FAULT PERSISTS
Has the motor reached full
speed before use?
No
Allow the motor to reach full
speed before use.
Are you using the trimmer
correctly?
?
Only use tip of nylon line to trim.
SEE “How to trim and edge”.
Is the line jamming on the spool?
Yes
Rewind the line on the spool,
if symptoms still persist, change
spool and line.
Clean wheel and groove on trimmer head. SEE “MAINTENANCE”
WHEEL STOPS TURNING
F1 F2
Z1
S1
Cutting Head
K1
K2
N P
1
Plant Guard Assembly (B3) & (B4)
1. Open the plant guard as illustrated in fig. B3 and place into
the TOP groove on the trimmer head. Rotate the plant guard
clockwise until it CLICKS into its parked position (B4).
Safety Guard Assembly (C1) & (C2)
1. Locate the safety guard over the cutting head. Ensure the
nylon line is fed through the hole in the safety guard as
illustrated in fig. C1.
2. Push into location and turn safety guard in the direction
illustrated in fig. C2, until a click is heard and the safety guard
is securely locked in position.
• ENSURE THE SAFETY GUARD IS SECURELY IN PLACE
BY ATTEMPTING TO TWIST GUARD.
Steady Handle Assembly (D)
1. Pull the steady handle release lever towards the handle grip.
2. Depress the two buttons on the side of the steady handle.
3. Locate the buttons into the main handle and release the
lever.
4. Adjust the steady handle to the most comfortable operating
position by pulling the release lever and moving the handle.
Height Adjustment (E)
1. Turn height adjuster (E1) in the direction indicated to un-lock
(E2).
2. Adjust the length of the tube to the most comfortable
operating position.
3. Turn height adjuster in the opposite direction to lock (E3).
• ENSURE THAT THE TUBE IS FULLY SECURED.
Cable Restraint (F1) & (F2) (optional)
1. Form loop in mains cable and push the loop through the slot
as illustrated in picture (F1).
2. To secure, position loop over the hook and pull the cable
back through the slot as illustrated in picture (F2).
Wheel assembly (B1) & (B2)
1. Attach the wheel to the trimmer making sure that it is located
into the BOTTOM groove on the trimmer head as illustrated
in fig. B1.
2. Clip the wheel together on each side making sure it is secure.
(B2).
3. The wheel should turn freely.
• WARNING
Disconnect from the mains electricity supply, before
attempting any maintenance or adjustment. Cutting head
continues to rotate after the trimmer has been switched
off. Keep fingers and hands clear of the line cutter on
leading edge of guard.
Z2
CLICK!
1
3
2
CLICK!
1
2
3
X
2
1
5857342-02 Contour 500E-580E-650E AU/NZ.indd 2 14.06.15 11:25
Loading...