Flymo 500, 420 User Manual

®

EasiCut 420/EasiCut 450/

EasiCut 500/EasiCut 510

EasiCut 600XT

IMPORTANT INFORMATION

Read before use

& retain for future reference

EasiCut 420/450/500/510

EasiCut 600XT

Original Instructions

Carton Contents

IMPORTANT !
Please check the contents of the carton are correct BEFORE assembling your new product.
IF ANY PARTS ARE MISSING CONTACT:­Husqvarna UK Ltd. Customer Service Department direct
Telephone : [phone] UK 1800 882 350 ROI Fax : [phone]

instruction

manual

blade cover

Handguard

belt clip

instruction

manual

blade cover

Handguard

belt clip

EasiCut 420/450/500/510

EasiCut 600XT

If not used properly this product can be dangerous! This product can cause serious injury to the
operator and others, the warnings and safety instructions must be followed to ensure reasonable
safety and efficiency in using this product. The operator is responsible for following the warning
and safety instructions in this manual and on the product.

Explanation of Symbols on your product

Warning.

Read the user instructions carefully to
make sure you understand all the controls
and what they do.

Remove plug from the mains immediately
if the cable is damaged or cut.

Do not expose to rain.
Do not leave the product outdoors while it
is raining.

The use of eye protection is
recommended.

Safety

General Power Tool Safety Warnings

WARNING Read all safety warnings and all
instructions.

Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.

Save all warnings and instructions for future reference.

The term ‘“power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.

1) Work area safety
a) Keep work area clean and well lit.

Cluttered or

dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of
flammable liquids, gases or dust.

Power tools

create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause

you to lose control.

2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do not
use any adaptor plugs with earthed

(grounded) power tools.

Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and
refrigerators.

There is an increased risk of

electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will

increase the risk electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts.

Damaged or entangled

cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use.

Use
of a cord suitable for outdoor use reduces the risk
of electric shock.

f) If operating a power tool in a damp location is

unavoidable, use a residual current device
(RCD) protected supply.

Use of an RCD

reduces the risk of electric shock.

3) Personal safety
a) Stay alert, watch what you are doing and use

common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication.

A moment of inattention while
operating power tools may result in serious
personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such
as dust mask, non-skid safety shoes, hard had, or
hearing protection used for appropriate conditions
will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool.

Carrying power tools
with your finger on the switch or energising power
tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key
left attached to a rotating part of the power tools
may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves
away from moving parts.

Loose clothes,
jewellery or long hair can be caught in moving
parts.

g) If devices are provided for the connection of

dust extraction and collection facilities,
ensure these are connected and properly
used.

Use of dust collection can reduce dust-

related hazards.

4) Power tool use and care
a) Do not force the power tool. Use the correct

power tool for your application.

The correct
power tool will do the job better and safer at the
rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and off.

Any power tool that
cannot be controlled with the switch is dangerous
and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools.

Such
preventive safety measures reduce the risk of
starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.

Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for

misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation. If
damaged, have the power tool repaired before
use.

Many accidents are caused by poorly

maintained power tools.