FLYMO 280 User Manual

Husqvarna AB
S-561 82 Huskvarna
Sweden
IMPORTANT INFORMATION
Read before use
& retain for future reference
Carton Contents
IMPORTANT !
Please check the contents of the carton are correct BEFORE assembling your new Flymo product.
IF ANY PARTS ARE MISSING CONTACT:-
Husqvarna UK Ltd. Customer Service Department direct
Telephone : 0844 844 4558 UK 1800 882 350 ROI Fax : 01325 302530
electric cable
with moulded
on plug
instruction
manual
Safety
If not used properly this lawnmower can be dangerous! This lawnmower can cause serious
injury to the operator and others. Read the instructions carefully. Be familiar with the controls
and the proper use of the lawnmower. The operator is responsible for following the warning
and safety instructions in this manual and on the lawnmower. Never use the lawnmower
unless the grassbox or guards provided by the manufacturer are in the correct position.
Explanation of Symbols on your product.
Warning
Read the user instructions carefully
to make sure you understand all the
controls and what they do.
Always keep the lawnmower on the
ground when mowing. Tilting or lifting
the lawnmower may cause stones to be
thrown out
Keep bystanders away. Do not mow
whilst people especially children or pets
are in the mowing area
Beware of sharp blades - remove plug
from mains before maintenance or if
cable is damaged.
Blades continue to rotate after the
machine is switched off.
Keep the cable away from the blade.
switchbox
start/stop lever
General
1. This product is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning the use of
the product by a person responsible for their
safety. Children should be supervised to ensure
that they do not play with the product. Local
regulations may restrict the age of the operator.
2. Never allow children or people unfamiliar with
the instructions to use the machine.
3. Stop using the machine while people,
especially children, or pets are nearby.
4. Only use the lawnmower in the manner and for
the functions described in these instructions.
5.
Never operate the lawnmower when you are tired, ill
or under the influence of alcohol, drugs or medicine.
6.
The operator or user is responsible for accidents or
hazards occurring to other people or their property.
7. Read the user instructions carefully to make sure
you understand all the controls and what they do.
Electrical
1. We recommend the use of a Residual Current
Device (R.C.D.) with a tripping current of not
more than 30mA. Even with a R.C.D. installed
100% safety cannot be guaranteed and safe
working practice must be followed at all times.
Check your R.C.D. every time you use it.
2. Before use, examine the cable for signs of
damage or ageing. If the cable is found to be
defective, take the product to an Authorised
Service Centre and have the cable replaced.
3. Do not use the lawnmower if the electric cables
are damaged or worn.
4. Immediately disconnect from the mains
electricity supply if the cable is cut, or the
insulation is damaged. Do not touch the
electric cable until the electrical supply has
been disconnected. Do not repair a cut or
damaged cable. Replace it with a new one.
5. Your extension cable must be uncoiled, coiled
cables can overheat and reduce the efficiency
of your mower.
6. Keep cable away from the blades, the blades can
cause damage to the cables and lead to contact
with live parts. Always work away from the power
point mowing up and down, never in circles.
7. Do not pull cable around sharp objects.
8. Always switch off at the mains before disconnecting
any plug, cable connector or extension cable.
9. Switch off, remove plug from mains and examine
electric supply cable for damage or ageing before
winding cable for storage. Do not repair a
damaged cable, have it replaced with a new one.
10. Always wind cable carefully, avoiding kinking.
11. Never carry the product by the cable.
12.
Never pull on the cable to disconnect any of the plugs.
13. Use only on AC mains supply voltage shown on
the product rating label.
14. Our products are double insulated to EN60335.
Under no circumstance should an earth be
connected to any part of the product.
Preparation
1. While using your product always wear
substantial footwear and long trousers. Do not
operate when barefoot or wearing open sandals.
2.
Make sure the lawn is clear of sticks, stones, bones,
wire and debris; they could be thrown by the blade.
3.
Before using the machine and after any impact, check
for signs of wear or damage and repair as necessary.
4. Replace worn or damaged blades together with
their fixings in sets to preserve balance.
Use
1. Use the lawnmower only in daylight or good
artificial light.
2. Avoid operating your lawnmower in wet grass,
where feasible.
3. On slopes, be extra careful of your footing and
wear non-slip footwear.
4.
Mow across the face of slopes, never up and down.
5. Exercise extreme caution when changing
direction on slopes. Walk never run.
6. Do not mow excessively steep slopes.
7.
Do not walk backwards when mowing, you could trip.
8.
Never cut grass by pulling the mower towards you.
9. Switch off if the product has to be tilted for
transportation, when crossing surfaces other
than grass and when transporting the product
to and from the area to be mowed.
10. Never operate the lawnmower with damaged
guards or without guards in place.
11. Switch on the motor according to instructions
and with feet well away from the blade(s).
12. Do not put hands or feet near or under rotating
parts.
13. Do not tilt lawnmower when the motor is running.
14. Never pick up or carry a mower when it is
operating or still connected to the mains supply.
15. Remove the plug from the mains :
before leaving the mower unattended for any period;
– before clearing a blockage;
– before checking, cleaning or working on the mower;
– if you hit an object. Do not use your
lawnmower until you are sure that the entire
lawnmower is in a safe operating condition.;
– if the lawnmower starts to vibrate abnormally.
Check immediately. Excessive vibration can
cause injury.
Maintenance and storage
1. Caution: Do not touch rotating blade.
2. Keep all nuts, bolts and screws tight to be sure
the lawnmower is in safe working condition.
3. Check the grassbox/grassbag frequently for
wear or deterioration.
4. Replace worn or damaged parts for safety.
5. Only use the replacement blade, blade bolt,
spacer and impeller specified for this product.
6. Be careful during adjustment of the lawnmower
to prevent entrapment of the fingers between
moving blades and fixed parts of the machine.
7. If during the life of the product, the belt begins
to slip. Return the product to an Authorised
Service Dealer for maintenance.
8. Store in a cool dry place and out of reach of
children. Do not store outdoors.
9. Allow the product to cool for at least 30
minutes before storing.
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
Copyright © 2013 Flymo S.A. All rights reserved. Flymo
®
and other product and feature names are
registered or unregistered trademarks of Flymo S.A.
Husqvarna UK Ltd. are manufactured under an Environmental Management System (ISO 14001) using, where practical, components manufactured in the most environmentally responsible manner, according to company procedures, and with the potential for recycling at the end of the products’ life.
• Packaging is recyclable and plastic components have been labelled (where practical) for categorised recycling.
• Awareness of the environment must be considered when disposing of ‘end-of-life’ product.
• If necessary, contact your local authority for disposal information.
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council office, your household waste disposal service or the shop where you purchased the product.
Environmental Information
EC Declaration of Conformity
Husqvarna AB, S-561 82, Huskvarna, Sweden Declare under our sole responsibility that the product(s);
Designation .................................... Lawnmower
Designation of Type(s) ....................EG 280
Identification of Series ....................See Product Rating Label
Year of Construction ......................See Product Rating Label
Complies with the essential requirements & provisions of the following EC Directives:
2006/42/EC, 2006/95/EC, 2004/108/EC, 2000/14/EC, 2011/65/EU
based on the following EU harmonized standards applied: EN 60335-1, EN 60335-2-77, EN 55014-1, EN 61000-3-2, EN 61000-3-3, EN 62233, The maximum A weighted sound pressure level L
pA
at the operator’s position, measured according to EN60335-2-77,
is given in the table.
The maximum hand / arm vibration weighted value a
h
measured according to EN ISO 20643 on a sample of the
above product(s) is given in the table.
2000/14/EC: The Measured Sound Power L
WA
& Guaranteed Sound Power L
WA
values are according to the tabulated figures.
Conformity Assessment Procedure.................. Annex VI
Notified Body.................................................... Intertek, Cleeve Road
Leatherhead, Surrey KT22 7SB, England Huskvarna, 19 July 2013 P. Lameli Chief Technical Officer Keeper of technical documentation
Original Instructions
Hover Vac 280
5856188-01
Replacement Parts
Blade : EG280
Reference no.: FLY004
Part no.: 512762990
spanner
spacers
Type
Width of Cut (cm) Speed of Rotation of Cutting Device (RPM) Power (kW) Measured Sound Power L
WA
(dB(A))
Guaranteed Sound Power L
WA
(dB(A))
Sound pressure L
pA
(dB(A))
Uncertainty K
pA
(dB(A))
Hand / arm vibration
a
h
(m/s2)
Uncertainty Ka
h
(m/s2) Weight (kg) Rated voltage/Rated frequency/Rated input
EG280
30
4,300
1.30 89 91 80
2.5
3.56
1.5
8.5
230 V (AC)/50 Hz/1.3 kW
®
5856188-01 Hover Vac 280 UK.indd 15856188-01 Hover Vac 280 UK.indd 1 11.10.13 08:3411.10.13 08:34
A
Assembly
Fault Finding Hints
CABLES – IMPORTANT
If you want to use an extension cable when operating your product, only the following cable dimensions should be used: – 1.0 mm
2
: max length 40 m
– 1.5 mm
2
: max length 60 m
– 2.5 mm
2
: max length 100 m
Minimum rating:
1.00 mm
2
size cable, 10 amps 250 volts AC.
YOUR PRODUCT IS SUPPLIED WITH CABLE
WIRED DIRECTLY INTO THE PRODUCT.
1. If the supply cord is damaged, it must be replaced by your local Husqvarna UK Ltd. Approved Service Centre or similarly qualified persons in order to
avoid a hazard.
2. Flymo Extension Cables are available from your local Husqvarna UK Ltd. Approved Service Centre.
3. Do not wire an extension cable directly to your product yourself. Please contact your local Husqvarna UK Ltd. Approved Service Centre for further information on the connectors and kits available.
4. Only use extension cables specifically designed for out door use and which conform to one of the fol­lowing specifications: Ordinary rubber (60245 IEC
53), Ordinary PVC (60227 IEC 53) or Ordinary PCP (60245 IEC 57).
CONNECTORS – IMPORTANT
• Flymo connectors are suitable for use with 2 core cable only. Under no circumstances should these connectors be used for earthed products.
• All Flymo connectors and cables are of splashproof construction. They are not waterproof and must not
be left outside permanently nor should they be submerged or immersed in water. Do not let cable lay or trail through pools of water or splashed with water from hose pipes.
MAINS PLUG REPLACEMENT – IMPORTANT
• If the plug supplied is cut off it should be destroyed. There is an electric shock hazard if a cut off plug is inserted into a 13 amp socket.
1. No earth required. Flymo products are double
insulated to EN60335 and under no circumstances should an earth be connected to any part of the product.
2. Ensure the mains voltage suits your product
3. IMPORTANT! The wires in the mains lead are coloured in accordance with the following code: BLUE – NEUTRAL BROWN – LIVE
The wire which is coloured BLUE must be
connected to the Terminal which is marked with the letter 'N' or coloured BLACK.
The wire which is coloured BROWN must be
connected to the Terminal which is marked with the letter 'L' or coloured RED.
4. It is important that the outer sheath is clamped correctly into the 3-pin plug.
5. If in doubt consult your local Service Repairer or qualified electrician before the machine is used.
6. A 13 Amp fuse must be fitted to the Mains Plug.
7. The normal plug fuse and household fuse only protect the electrical equipment and are not a safeguard against electrocution.
Preparing your lawnmower for use
• Your lawnmower is supplied with the upper handle folded over the machine for packing and transportation.
Handle in Operating Position
1. Lift handle as illustrated in figure A.
• Do not drop the handle.
• Make sure that the cable does not become trapped between the handles.
To Start your Lawnmower
1. Connect plug to mains and switch on.
The switchbox is provided with a lock-off button (B1) to prevent accidental starting.
2. Press and hold the lock-off button (B1) on the
switchbox, then squeeze the Start/Stop levers towards the upper handle (C).
3. Continue to squeeze the start/stop lever towards the
upper handle and release the lock-off button.(D)
IMPORTANT: Do not use the start/stop lever
intermittently.
To Stop your Lawnmower
1. Release the pressure on the Start/Stop lever.
Starting and Stopping
B
D
1
Caring for your Lawnmower
Cleaning
IMPORTANT: It is very important that you keep
your lawnmower clean. Grass clippings left in any of the air intakes or under the deck could become a potential fire hazard.
USE GLOVES
Switch off and remove the plug from the mains before cleaning. It is recommended that you clean your lawnmower straight after mowing while the grass is still wet.
1. Remove grass from under the deck with the spanner/
scraper tool. (N)
2. Using a soft brush - remove grass clippings from all air intakes, the grassbox and the grassbox vision window. (P & Q)
3. Clean the impeller inlet with a soft brush. (R)
4. If jammed lever the roller out of position and clean with a soft brush.(S).
5. Wipe over the surface of your lawnmower with a dry cloth. (T)
IMPORTANT: Never use water for cleaning your lawnmower. Do not clean with chemicals, including petrol, or solvents - some can destroy critical plastic parts.
Storing the lawnmower
The handles can be folded to take up the minimum of space.
1. Hold onto the lower handle with your left hand (V).
2. Hold the upper handle with your right hand and push in the direction of the arrow.
3. Move the handle slowly forward to rest it on the lawnmower. Do not drop the handle.
• Ensure the switchbox cable is not trapped.
• Store in a dry place where your lawnmower is protected from damage.
Transporting the lawnmower.
The lawnmower may be transported on its roller (W).
At the End of the Mowing Season
1. Replace blade and blade bolt, if necessary.
2. Clean your lawnmower thoroughly.
3. Ask your local Service Centre to clean the air filter thoroughly and carry out any service or repairs required.
N
R
P
Fails to Operate
1. Is the correct Starting procedure being followed?
See ‘To Start your Lawnmower’
2. Is the Power Turned On?
3. Check the fuse in the plug, if blown replace.
4. Fuse continues to blow?
Immediately disconnect from the mains electricity
supply and consult your local approved Service Centre.
Poor Flotation
1. Disconnect from the mains electricity supply.
2. Clean the underside of the deck and the fan blades.
3. Raise to a higher height of cut. See ‘Adjusting the
Cutting Height’.
4. If poor flotation persists?
Disconnect from the mains electricity supply and
consult your local approved Service Centre.
Poor Collection
1. Is the grassbox lid firmly closed?
2. Is the grassbox fitted correctly?
3. See “How to Mow”.
4. Check all air vents and openings are not obstructed.
5. Raise to a higher height of cut. See ‘Adjusting the Cutting Height’.
6. If poor collection persists?
Disconnect from the mains electricity supply and
consult your local approved Service Centre.
Excessive Vibration
1. Disconnect from the mains electricity supply.
2. Check that the blade is fitted correctly?
3. If the blade is damaged or worn, replace it with a new one.
4. If vibration persists?
Immediately disconnect from the mains electricity supply and consult your local approved Service Centre.
If any part is found to be defective due to faulty manufacture within the guarantee period, Husqvarna UK Ltd., through its Authorised Service Repairers will effect the repair or replacement to the customer free of charge providing: (a) The fault is reported directly to the Authorised
Repairer. (b) Proof of purchase is provided. (c) The fault is not caused by misuse, neglect or faulty
adjustment by the user. (d) The failure has not occurred through fair wear and
tear. (e) The machine has not been serviced or repaired,
taken apart or tampered with by any person not
authorised by Husqvarna UK Ltd.. (f) The machine has not been used for hire. (g) The machine is owned by the original
purchaser. (h) The machine has not been used commercially. * This guarantee is additional to, and in no way
diminishes the customers statutory rights. Failures due to the following are not covered, therefore it is important that you read the instructions contained
in this Operator's Manual and understand how to operate and maintain your machine:
Failures not covered by guarantee
* Replacing worn or damaged blades * Failures as a result of not reporting an initial fault. * Failures as a result of sudden impact. * Failures as a result of not using the product in
accordance with the instructions and recom­mendations contained in this Operator's Manual.
* Machines used for hire are not covered by this
guarantee.
* The following items listed are considered as wearing
parts and their life is dependent on regular maintenance and are, therefore not normally subject to a valid warranty claim: Blades, Belt, Electric Mains cable.
* Caution!
Husqvarna UK Ltd. does not accept liability under the warranty for defects caused in whole or part, directly or indirectly by the fitting of replacement parts or additional parts that are not either manufactured or approved by Husqvarna UK Ltd., or by the machine having been modified in any way
Guarantee & Guarantee Policy
Service Recommendations
1. We strongly recommend that your product is serviced at least every twelve months, more often in a professional application.
2. Always use genuine Flymo Spare Parts.
3. Prepacked spares are available from most Husqvarna Outdoor Products stockists.
4. Your product is uniquely identified by a silver and black product rating label
5. If you have a problem with your machine contact your local Approved Service Centre ensuring you have full details of your product as described on the product rating label.
6. Should it be necessary for work to be carried out
by your Service Centre, it is important to take your complete machine including cable and any extension cables used.
A network of specialist dealers can be found in your local Yellow Pages. To obtain service on your Flymo product simply telephone or visit your local Service Centre. Should you require service under the terms of our guarantee the Service Centre will require proof of purchase.
All of the centres listed stock genuine Flymo Spare Parts. NOTE: Our Service Repairers act on their own behalf and are not empowered to commit or legally bind Husqvarna UK Ltd. in any manner whatsoever.
C
Cables
Removing, Emptying and Refitting the Grassbox
How to Mow
Adjusting the Cutting Height
Always handle the blade with care - sharp edges could cause injury. USE GLOVES. Never use more than 3 Cutting Height Spacers. Spacers must only be fitted between the blade and the fan and NEVER between the blade and the bolt.
1. Remove the blade bolt, and blade as described in
Removing the Blade and Fan.
2. For a Lower Cut – Add spacers to a maximum of 3.
3. For a Higher Cut – Take spacers away.
4. Refit the blade as described in Fitting the Blade
and Fan.
5. For a healthy lawn, we recommend that you do not cut below 25mm (Use more than 2 spacers).
6. Always ensure the text ‘GRASS SIDE’ will be facing the grass when the product is in the mowing position (L).
L
Removing and fitting the Blade and Fan
Switch off and remove the plug from the mains. Removing the Blade and Fan. USE GLOVES.
1. To remove the blade bolt, hold the fan firmly and with the spanner provided loosen the blade bolt by turning it anti-clockwise (L).
2. Remove the blade bolt, blade, spacers and fan (M).
3. Inspect for damage and clean as necessary.
Renew your metal blade after 50 hours mowing or
2 years whichever is the sooner – regardless of condition. If the blade is cracked or damaged replace it with a new one. Never use a blade bolt if the insulated head is damaged cracked or missing.
Fitting the Blade and Fan. USE GLOVES.
1. Ensure the fan (M4) is located correctly.
2. Place the spacers (M3) onto the fan ensuring the pegs have located into the holes.
3. Place the blade (M2) onto the spacers ensuring the text ‘GRASS SIDE’ (M5) will be facing the grass when the product is in the mowing position. Ensure the pegs have located into the holes on the blade and that the blade is positioned as illustrated in Figure M.
4. Place the blade bolt (M1) through the centre hole of the blade.
5. Tighten down clockwise by hand.
6. Hold the fan firmly and tighten the blade bolt with the spanner provided.
1
2
4
3
M
5
T
W
S
V
Grassbox Full Indicator (if fitted)
Your lawnmower may be fitted with a vision window.
• IMPORTANT
When the window is full it is time to empty the
grassbox.
Emptying the Grassbox
• Stop the lawnmower, as described in ‘To Stop your Lawnmower’ and wait until the blade has stopped rotating, BEFORE lifting the grassbox lid.
1. Lift the grassbox lid and rest it against the motor cover (J).
2. Remove the grassbox using the moulded handle recesses at the front and rear of the grassbox. (K).
3. Empty grassbox.
4 Replace grassbox and lid carefully.
Failure to fit the grassbox and grassbox lid
correctly will cause poor collection of grass clippings.
Q
H
1
2
G
1. For the best results mow the outside edge of the lawn in a clockwise direction first. (G1)
2. Then start mowing the edge of the lawn nearest to the power point so the cable is laid out on the lawn you
have already cut. (G2)
3. For best grass collection always mow in a straight line (E), do not swing the lawnmower from side to side (F)
Do Not Overload Your Mower
Mowing long thick grass may cause the motor speed to drop, you will hear a change in the motor sound. If the motor speed drops you may overload your lawnmower which may cause damage. When mowing in long thick grass a first cut with the cutting height set higher will help reduce the load. See Adjusting the Cutting Height.
Mow twice a week during the growing season, your lawn will suffer if more than a third of its length is cut at one time and this may also result in poor collection.
E
F
ü
x
K
1
5856188-01 Hover Vac 280 UK.indd 25856188-01 Hover Vac 280 UK.indd 2 11.10.13 08:3411.10.13 08:34
Loading...