Fly Blocks DIY Build N' Fly Drone 4 in 1 User Manual

1.CAUTIONS:

This products is not a toy, it is a precise device which requires accurate assembly
and debugging to avoid potential accidents. It should be operated in accordance with
the User manual. it is the user’s responsibility to fly and operate this drone
responsibly keeping far away from people or property.
(1) Not suitable for children under 14 and without model operating experience and
adult supervision
(2) Please respect any local regulations
(3) We will not be responsible for any damage caused by improper operation
(4) For any technical support and after-sale service, please contact your local
distributor

2.WARNINGS:

The drone can cause harm. Please keep do not operate near people, crowds or
property. Proper assembly of the drone is essential. Improper assembly, poor control
or being unfamiliar with operations, may cause harm. Please be cautious.
(1) Keep away from people, high-rise buildings, high-voltage lines. Avoid flying in high
winds or stormy weather to ensure safety
(2) Keep away from humid conditions to avoid malfunction
(3) Keep away from the blades to avoid danger and damage
(4) Keep away from heat to avoid deformation or damage by high temperature. Store
in a cool, dry area
(5) Safely operate the drone according to your own flying skills.
(6) Ensure the blades are installed correctly, or it will not fly.

3.ATTENTION BEFORE FLIGHT:

(1) Please fly the drone in an open space
(2) Please make sure the battery is fully charged
(3) Please make sure the accelerator stick in the lowest position before turn on the
controller
(4) Please check the connection of the battery and motor parts before flying.

4.BATTERY WARNINGS:

(1) Do not over discharge
(2) Do not overcharge
(3) Please keep the drone with 60% power if you do not play it for a long time.
recharge for every 4 or 5 months
(4) If you notice swelling or significant over heating of the battery please do not use.
(5) Research proper disposal in your area for any old or unwanted batteries.

Product Size: 17.5 x 14.5 x 1.5 cm

Up/down, left / right, forward / backward
Headless mode
6-axis gyro
Battery: 3.7V 900 lithium polymer

Charging time: 30~90 minutes (depending on adaptor)

WARNING: Read the manual thoroughly before flying.

Do not fly without understanding the contents of

this manual.

www.FlyBlocks.com

DIY Build N' Fly Drone
4 in 1!

3

MODEL 1 DRONE ASSEMBLY (4 AXIS)

2

FUNCTION AND DESCRIPTION OF THE CONTROLLER

LIST OF COMPONENTS

Plode honge X1

Building block with 6 holes X14 Rubber band X2

Motor Base X9

Building block with 8 holes X1 Square building block X3

Blade X12

Motor X6 Battery X1

Manual X1

USB Charging Line X1 Rubber Band X2 Controller X1

Building block with 1 holes X20

Receiver box X1

Forward / backward
micro adjust

Right stick
(Forward / backward,
Left / right side-flying)

Left stick
(Up / down,
Turn left /
turn right)

Speed button
(High speed)

Speed button
(Low speed)

Left / right
micro adjust

Headless mode

Power switch

Product Size: 17.5 x 14.5 x 1.5 cm

Up/down, left / right, forward / backward
Headless mode
6-axis gyro
Battery: 3.7V 900 lithium polymer

Charging time: 30~90 minutes (depending on adaptor)

Read the manual thoroughly before flying

Please use the product with knowledge of the contents

5

MODEL 2 DRONE ASSEMBLY (4 AXIS)

4

MODEL 1 DRONE ASSEMBLY (4 AXIS)

Battery base

Install Motor With
Red&Blue Cables

Install Motor With
Red&Blue Cables

Install Motor With
Black&White Cables

Install Motor With
Black&White Cables

ATTENTION:
Must install the motors
correctly. Failure do do
so will result in a crash
or render the drone
inoperable.

L Blade

L Blade

S Blade

S Blade

Bind the battery to the drone with rubber band