Fluke 960PS-210, 960PS-200 User Manual
Victoreen®
960PS-200 & 960PS-210
Power Supply Modules
March 2005
Manual No. 960PS-200-1 Rev. 2
©2004, 2005 Fluke Corporation, All rights reserved. Printed in U.S.A.
All product names are trademarks of their respective companies
Operators Manual
Fluke Biomedical
Radiation Management Services
6045 Cochran Road
Cleveland, Ohio 44139
440.498.2564
120 Andrews Road
Hicksville, New York 11801
516.870.0100
www.flukebiomedical.com/rms
Table of Contents
Section 1: Introduction................................................................................................ 1-1
1.1 General Description ..................................................................................... 1-1
1.2 Application ................................................................................................... 1-1
1.3 Specifications............................................................................................... 1-1
1.4 Receiving Inspection and Storage ............................................................... 1-2
1.5 Installation.................................................................................................... 1-3
1.6 Procedures, Warnings, and Cautions .......................................................... 1-3
Section 2: Operation.................................................................................................... 2-1
2.1 960PS-200 Power Supply............................................................................ 2-1
2.2 Input Filter.................................................................................................... 2-1
2.3 DC to DC Converter..................................................................................... 2-1
2.4 Voltage Regulation ...................................................................................... 2-1
2.5 960PS-210 Power Supply............................................................................ 2-2
Section 3: Maintenance, Calibration and Troubleshooting...................................... 3-1
3.1 Maintenance ................................................................................................ 3-1
3.2 Calibration.................................................................................................... 3-1
3.3 Troubleshooting ........................................................................................... 3-1
Appendix A: Connector Designations ...........................................................................A-1
A.1 Connector Designations............................................................................... A-1
Appendix B: Applicable Drawings and Bill of Materials ............................................... B-1
B.1 Applicable Drawings ....................................................................................B-1
B.2 Bill of Materials ............................................................................................B-1
i
(Blank Page)
Introduction
General Description
1
Section 1
Introduction
1.1 General Description
The 960PS Power Supply is used to supply power to the modules that are plugged into the
960MB/961MB motherboards.
The power supply is mounted outside of the 960CC Card Cage Module, the wall mounted Local Control
Unit enclosure, or control room cabinet. The input AC voltage is soft started to inhibit current surges when
powered up. EMI protection is also provided as part of the AC voltage protection. The power supply has
remote error sensing and short circuit/overload protection along with input and output over-voltage
protection. See Figure 1-1, the Power Supply Functional Block Diagram.
1.2 Application
The 960PS-200 & 960PS-210 Power Supply Modules are used in VICTOREEN series area monitors,
process monitors, isolators, control rooms, and safety-related display cabinets.
1.3 Specifications
General specifications for the power supply are listed below.
960PS-200
Dimensions (W x H x D) 4.2 x 2.25 x 6.66 in 5.0 x 2.5 x 10.5 in
Operating Temperature 0° to 50°C, Full Rated 0° to 50°C, Full Rated
Relative Humidity 95% Non-Condensing 95% Non-Condensing
Input Voltage 115 VAC ± 15% 90 - 132 VAC/180 - 240 VAC
60 Hz ± 5% selectable) 47 - 440 Hz
Input Power 155 watts 130 watts
Efficiency 71% 75% Minimum
Input Filtering Common Mode Common Mode and Differential
Mode
Output Voltages +5 VDC ± 0.2% @ 10 Amps +5 VDC ± 0.2% @ 15 Amps
+15 VDC ± 5% @ 2 Amps (10% load required for regulation)
-15 VDC ± 5% @ 2 Amps +15 VDC ± 2% @ 3 Amps
-15 VDC ± 2% @ 2 Amps
+24 VDC ± 1.5% @ 2 Amps
960PS-210
(jumper
Remote Error Sensing +5 VDC Sense Provided +5 VDC Sense Provided
Fault Protection Short circuit protected by current Short circuit protected by current
foldback with automatic recovery foldback with automatic recovery
Line Voltage Monitor Not Provided Factory Set to 90 VAC
1-1
Loading...