Fluke 700G User Manual

Safety Information

700G Series

Pressure Gauge

PN 4098606
November 2011

© 2011 Fluke Corporation. All rights reserved. Printed in USA.
All product names are trademarks of their respective companies.

LIMITED WARRANTY AND LIMITATION OF LIABILITY

This Fluke product will be free from defects in material and workmanship for three years from the date of purchase. This
warranty does not cover fuses, disposable batteries, or damage from accident, neglect, misuse, alteration, contamination, or
abnormal conditions of operation or handling. Resellers are not authorized to extend any other warranty on Fluke’s behalf.
To obtain service during the warranty period, contact your nearest Fluke authorized service center to obtain return
authorization information, then send the product to that Service Center with a description of the problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR
PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some states or countries
do not allow the exclusion or limitation of an implied warranty or of incidental or consequential damages, this limitation of
liability may not apply to you.

11/99

Fluke Corporation
P.O. Box 9090
Everett, WA 98206-9090
U.S.A.

Fluke Europe B.V.
P.O. Box 1186
5602 BD Eindhoven
The Netherlands

Safety Information

A Warning identifies conditions and procedures that are
dangerous to the user. A Caution identifies conditions
and procedures that can cause damage to the Product or
the equipment under test.

XWWarning

To prevent possible electrical shock, fire, or
personal injury:

• Use the Product only as specified, or the

protection supplied by the Product can
be compromised.

• The battery door must be closed and

locked before you operate the Product.

• Replace the batteries when the low

battery indicator () shows to prevent
incorrect measurements.

• Do not use and disable the Product if it

is damaged.

• Read all safety Information before you

use the Product.

• Do not use the Product in damp or wet

environments.

• Batteries must only be changed in an

area known to be non-hazardous.
Explosion hazard.

• Do not use the RS-232 interface in

hazardous areas.

WCaution

To avoid possible damage to Product or to
equipment under test:

• If the display reads “OL” the range limit

is exceeded and the pressure source
must immediately be removed.

• Do not exceed the maximum torque

allowed. Maximum torque allowed is
13,5 Nm = 10 ftlbs.

1

700G Series

Safety Information

Hazard Location Information/Approvals

Ex Hazardous Areas

An Ex-hazardous area as used in this manual refers to an
area made hazardous by the potential presence of
flammable or explosive vapors. These areas are also
referred to as hazardous locations, see NFPA 70 Article

500.

) ® LR110460

Class I, Div. 2, Groups A-D

( II 3 G Ex nA IIB T6

KEMA 06ATEX0014 X
Ta=–10 °C... +55 °C

Special Conditions for Safe Use

Misuse

If the Product is exposed to overpressure or sudden
physical shock (such as being dropped) examine it for
any damage that can cause a safety concern. If
necessary, return the Product for evaluation to Fluke.
Refer to the How to Contact Fluke section.

WWarning

To prevent possible fire, or personal injury:

• Do not use the Product with flammable

substances.

• The Product is intended for installation

only in locations providing adequate
protection against the entry of solid
foreign objects or water capable of
impairing safety.

2

Pressure Gauge

Safety Information

Symbols

Symbols used on the Product and in this manual are
explained in Table 1.

Table 1. Symbols

Symbol Meaning Symbol Meaning

W Risk of danger. Important information. See manual. P Conforms to European Union directives.

X Hazardous voltage. Risk of electrical shock. )

f Pressure ~

Conforms to relevant North American
Safety Standards.

Do not dispose of this product as
unsorted municipal waste. Go to Fluke’s
website for recycling information.

 Conforms to relevant Australian standards. ( Conforms to ATEX requirements

3

700G Series

Safety Information

How to Contact Fluke

To contact Fluke, call one of the following telephone numbers:

• Technical Support USA: 1-800-44-FLUKE (1-800-443-5853)

• Calibration/Repair USA: 1-888-99-FLUKE (1-888-993-5853)

• Canada: 1-800-36-FLUKE (1-800-363-5853)

• Europe: [phone]

• Japan: [phone]

• Singapore: [phone]

• Anywhere in the world: [phone]

Or, visit Fluke’s website at www.fluke.com.

To register your product, visit http://register.fluke.com.

To view, print, or download the latest manual supplement, visit http://us.fluke.com/usen/support/manuals.

4