Fluid E920 Owner's Manual

Owners Manual

Wheelchair Acces­sible

2

Contents

1. Contents of E920 Box.

2. E920 Assembly Instructions.

3. E920 Control Arm.

4. E920 Slider Arm Kit.

5. Tank Filling and Water Treat­ment.

6. Long Term Water Treatment

and Basic Operation.

7. The E920 Ergometer.

8. Maintenance/Troubleshooting.

9. Tank Belt Drive Adjustment.

10. Parts List and Warranty.

Do not remove hands while crank is in
motion. The crank will continue to rotate
and could cause injury.

As with any piece of fitness equipment,
consult a physician before beginning your
E920 exercise program.

CAUTION

WARNING

3

Box Contents E920

Hex Key
M3x130x25

4x Spring Washers
M8

2x Mainframe Bolts
M10x 25

4x Frame Bolt
Washers
21x11x2

1x Seat and Base

1x Main Frame with Telescoping Tube and
Internal Gas Assist Shock

1x Fill Funnel and
Hose

3x Frame levelers

1x Multi-Tool

2x Mainframe Nylock Nut
M10x2

1x M6
Hex Key

E-920 Slider
arm kit

Slider Arm Kit includes 1x Slider Arm
Assembly Right (includes right han­dle), 1x Slider Arm Assembly Left
(includes left handle), 2x Yellow Ad­justment Knobs with Nylon Spacers.

Owners Manual

2x AA Batteries

8x Chlorine Tablets

1x Blue Dye

Touch Up Paint

4x Telescoping
Tube Attachment
Bolts M8x15

4

E920 Assembly Instructions

Adjuster Knob

Step 1: Remove contents from box. Attach telescoping tube to the underside of the
control arm using 4x M8x15mm bolts and 4x M8 spring washers.

The control arm is heavy and will swing freely during this stage of assembly. The ad­juster knob is pre-tightened from the factory in the optimal position for assembly in rela­tion to the control arm. Do not loosen the Adjuster knob until the telescoping tube has
been safely secured to the underside of the control arm.

Step 1a: Thread the 3x foot levelers into underside of base. Adjust as required.

CAUTION

4x 8x15mm Bolts
and 4x M8 Spring
Washers

3x Foot Leveler

5

E920 Assembly instructions

M10 Nylock Nut

21x11x2 Washer

M10x25mm Bolt

Step 2: Attach base plate to lower mainframe using 2x
M10x25mm bolts, 2x M10 Nylock nuts and 4x 21x11x2 washers.

Step 3: Tilt the seat rearward until transport wheel is engaged. Secure the seat in
any of the 4 adjustment slots, or leave off entirely if wheelchair access is required.

6

The E920 Control Arm

Crank arm bolts: Loosen

all 8 bolts slightly before
adjusting/tightening chain.

Handgrip: Loosen knob
to adjust handle position
from 0-90 degrees.

E920 Slider Arms: Refer to
following assembly page.

Inspection plate: Open to check chain tension.
With a screwdriver or other implement, check
tension just behind front sprocket.

Note: A properly adjusted chain will have 3mm­5mm of slack only. See top of page for adjust­ment details.

Warning: Do not check chain tension by
Hand!

Chain tensioning bolts: Allows for tightening the chain or adjustment from side to side.
Make sure when tightening only to adjust the same amount for both bolts, otherwise the
sprocket will be misaligned.

Note: Tightening the right bolt only (turning clockwise) will pull the right side of the crank
assembly toward you, tightening the left will pull the left side toward you. Use this feature
to realign the rear with the front sprocket if needed or when changing to a new chain.

Adjustment Knob: Loosen to allow
the control arm to travel through 90
degrees of travel. Note the tele­scoping tube is gas assisted.

Tighten securely when desired
workout position is reached.

7

E920 Slider Arm Kit Installation Instructions

Slider Arm Kit includes 1x Slider

Arm Assembly Right (includes right
handle), 1x Slider Arm Assembly
Left (includes left handle), 2x Yellow
Adjustment Knobs with Nylon Spac­ers and 1x 3mm Allen key.

Note: Slider Arms are marked ‘L’
and ‘R’.

Improper installation will result in
uneven Slider Arm adjustment.