Podpoi = a pair of podlights with owleashes. Each podlight has 10 adjustable modes,
a preset mode with 10 patterns, a nocturnal mode to optimize battery life, and a “favorites”
mode that recalls your last 10 saved patterns (mode+adjustment). Either the speed, color
palette, brightness or preset patterns can be selected or adjusted in each mode. It charges
in 1-2 hours from USB power and most modes last all night or longer!
BUTTON INTERFACE
There is a single recessed button on the bottom of the podlight. To turn on, press the
button – it will enter the pattern it was most recently in.
Select a mode: Press the button briey (short press), the light will blink and enter the
next mode. The last mode is o.
Adjust a mode: Hold the button for over half a second (long press), let go when the
light ashes, before it turns o. The mode will now cycle through its adjustment range.
When you like what you see, press the button once (short press) to select the adjustment. You may also leave the podlight in “adjust” for a constantly changing eect :)
Turn o: There are 2 ways to turn o the podlight:
1. Hold the button until it turns o – about 1.5 sec (long hold) – the podlight will
blink and fade out. This records the last pattern you were in, and the pod will return
to it when you turn it back on. There is also a “favorites” mode that allows you to
select from the last 10 patterns you recorded.
2. You may also cycle through the modes until it turns o. This will reset the light
to mode1, default adjustment. All modes start in the default adjustment when you
change modes.
Micro-USB charging jack:
max. power-draw: 500mA
Flowleash: inverted ultra-slick owleash design
Length: 118mm | Diameter: 66mm | Weight: 128g | Battery: 3.7v, 750 mAh rechargeable Li-ion
Tri-ring: polycarbonate tri-petal ring
closes the top
Leash knot: a knot secures the leash
inside the pod/capsule
Pod: silicone outer shell
Capsule O-ring: thick silicone O-ring
seals the top of the capsule
Capsule: polycarbonate light-unit inside pod
Button: single recessed button
on bottom of pod
podpoi
Capsule C-ring: polycarbonate C-ring
seals the bottom of the capsule and
secures it inside the pod
POWER
Checking your battery charge level: When o, press and hold the button. The light
will blink a color indicating your charge level - ranging from red to green - and then
fade out.
Red = really low, less than 10% left
Orange = OK, about 50% left
Yellow = should last a while, 50-90%
Green = good to go! 90% or more
Note: Colors are approximate. Runtimes vary greatly with dierent modes.
Dead battery indicator: If your podlight blinks red and turns o, the battery is dead.
ASSEMBLY INSTRUCTIONS For video instructions please visit owtoys.com.
Removing and re-inserting the capsule inside the pod:
You should NOT need to remove the capsule, but if you choose to – please BE AWARE!
• DO NOT TEAR the seam between the petals - be gentle here
• DO NOT TWIST when removing the capsule from the pod - this can remove the C-ring
• grip the entire pod and use the leash to pull the capsule out, or push up from the bottom,
through the silicone around the button, get it started and then pull out from the top
ALWAYS BE SURE THE C-RING IS INSTALLED ON THE BOTTOM OF YOUR CAPSULE BEFORE
PUTTING IT BACK IN THE POD. The C-ring is CRITICAL to securing the capsule in the pod and allowing
the button to function properly. If the C-ring is stuck inside the pod, push it up from the bottom until it
can be shed out with a nger from the top, and re-install it on the capsule.
Adjusting the length of your leash:
Podpoi are designed to work with adjustable owleashes for the slickest connection
possible:
• pull the excess cord through the ring near handle to get to your desired leash length
• mark the point where the excess cord meets the small ring (any pen should do)
• pull back some slack on the excess side of the cord, cut at the mark
• melt the end until it makes a substantial disk of melted cord-tip. Tip: practice on the extra cord rst!
• let cool, pull the cord tight and enjoy!
After adjustment, all excess leash-cord should be removed, leaving only a small melted
tip and tiny metal o-ring at the swivel, and internal knot connection at the poi-head.
Visit owtoys.com for detailed video instructions.
• Computers/laptops with built-in USB jacks
• Powered USB hubs
• Solar USB chargers
• Cell phone/mobile device charging stations
commonly found in airports, malls and events
Note: Some smaller USB power supplies, such as bluetooth headset chargers, may provide only 200mA of power or
less. This will take longer to charge or may quit charging shortly after it starts as the power supply shuts down.
Common USB power sources:
mode default pattern adjustment
charge indicator
breathing color indicator (on USB power) brightness
n/a
rainbow
saturated fading rainbow speed of color fade
7
rainbow drops
saturated rainbow blips strobe speed
21
bold
full-on white color, saturated + pastels
6
lantern
warm light - great mood/ashlight brightness
6
re
ying reballs color palette
12
water
watery waves color palette
15
earth
blocky layers color palette
17
air
uy clouds in the sky color palette
16
spirit
ethereal inter-phasing blips color palette
58
strobe
bright white strobe strobe speed
13
presets
10 preset patterns (see below) select pattern
see table
nocturnal
all 20 patterns optimized to run for 15+ hrs select pattern
15+
favorites*
10 most recently saved patterns select pattern*
n/a
Charging the battery: There is a micro-USB jack on the side of the light unit in the
podlight. You do not need to remove the light capsule from the pod to charge them.
Simply press the tip of the pod down to spread the petal-seams and expose the inside of
the pod. Locate the USB-jack and plug in! If the jack is not perfectly aligned with one of
the seams, rotate the capsule until it is.
To charge your podlight, plug it into any USB power source with a standard micro-USB
cable. The pod should turn on and begin “breathing” in its charge-level color. When
charging, the indicator light is not entirely accurate until it’s actually green (which means
it’s done). The pod takes about 2 hours to fully charge, but 90% of the charge happens in
the rst hour!
You can leave your podlight on as it charges! This makes an excellent mood/nightlight.
You can leave it plugged in and running 24/7 and it will always be ready for use. It may
take 3-4 hours to fully charge if running brightly while charging.
*FAVORITES MODE
Favorites has a special kinetic
behavior during adjust. It will cycle
through its patterns for 5 sec. each,
just like presets or nocturnal modes,
but when you start spinning, it will
pause the cycle and remain on the
currently displayed pattern until you
stop. When you stop, the podpoi will
jump to the next pattern and
continue to cycle every 5 sec. This
feature enables you to create a
“playlist” of recorded patterns, and
“cue” them without having to press
the button, just stall!
Visit owtoys.com for more details.
preset pattern description
candy multi-colored candy bracelet 13
petals ethereal multi-colored petals 77
love soft pulsing shades of pink 16
watermelon juicy pink + green 22
freedom bold red, white + blue 12
beads multi-colored beaded necklace 26
microdots inter-phasing dots of rainbow light 46
unicorn pastel fantasy rainbow 14
solar are bright bursts on golden sun surface 77
are-up ickery re with bright bursts during
stalls (sensitivity may vary between poi)
resets all modes to default adjustment - favorites are saved
o
PODPOI MODES/ADJUSTMENTS
approx.
28
approx. owtime (hrs)
owtime (hrs)
ASSEMBLY INSTRUCTIONS For video instructions please visit owtoys.com.
Removing and re-inserting the capsule inside the pod:
You should NOT need to remove the capsule, but if you choose to – please BE AWARE!
• DO NOT TEAR the seam between the petals - be gentle here
• DO NOT TWIST when removing the capsule from the pod - this can remove the C-ring
• grip the entire pod and use the leash to pull the capsule out, or push up from the bottom,
through the silicone around the button, get it started and then pull out from the top
ALWAYS BE SURE THE C-RING IS INSTALLED ON THE BOTTOM OF YOUR CAPSULE BEFORE
PUTTING IT BACK IN THE POD. The C-ring is CRITICAL to securing the capsule in the pod and allowing
the button to function properly. If the C-ring is stuck inside the pod, push it up from the bottom until it
can be shed out with a nger from the top, and re-install it on the capsule.
Adjusting the length of your leash:
Podpoi are designed to work with adjustable owleashes for the slickest connection
possible:
• pull the excess cord through the ring near handle to get to your desired leash length
• mark the point where the excess cord meets the small ring (any pen should do)
• pull back some slack on the excess side of the cord, cut at the mark
• melt the end until it makes a substantial disk of melted cord-tip. Tip: practice on the extra cord rst!
• let cool, pull the cord tight and enjoy!
After adjustment, all excess leash-cord should be removed, leaving only a small melted
tip and tiny metal o-ring at the swivel, and internal knot connection at the poi-head.
Visit owtoys.com for detailed video instructions.
5-7-13
• Computers/laptops with built-in USB jacks
• Powered USB hubs
• Solar USB chargers
• Cell phone/mobile device charging stations
commonly found in airports, malls and events
• Dynamo hand-crank USB power generators
• Wall-power USB adaptors*
• Car-power USB adaptors*
• Portable USB power packs*
*Available on owtoys.com
Note: Some smaller USB power supplies, such as bluetooth headset chargers, may provide only 200mA of power or
less. This will take longer to charge or may quit charging shortly after it starts as the power supply shuts down.
Common USB power sources:
n/a
7
21
6
6
12
15
17
16
58
13
15+
n/a
Charging the battery: There is a micro-USB jack on the side of the light unit in the
podlight. You do not need to remove the light capsule from the pod to charge them.
Simply press the tip of the pod down to spread the petal-seams and expose the inside of
the pod. Locate the USB-jack and plug in! If the jack is not perfectly aligned with one of
the seams, rotate the capsule until it is.
To charge your podlight, plug it into any USB power source with a standard micro-USB
cable. The pod should turn on and begin “breathing” in its charge-level color. When
charging, the indicator light is not entirely accurate until it’s actually green (which means
it’s done). The pod takes about 2 hours to fully charge, but 90% of the charge happens in
the rst hour!
You can leave your podlight on as it charges! This makes an excellent mood/nightlight.
You can leave it plugged in and running 24/7 and it will always be ready for use. It may
take 3-4 hours to fully charge if running brightly while charging.
LIFETIME WARRANTY
We oer free replacement on non-electronic parts and defective electronics,
and 50% credit for products or parts in any condition. If the tips in this guide
do not keep your podpoi working for years to come, please contact us at
returns@owtoys.com.
* Flowtoys reserves the right to refuse coverage to anyone abusing this warranty.
Please do not send us product without rst contacting us. It may be returned to sender.
Podpoi = a pair of podlights with owleashes. Each podlight has 10 adjustable modes,
a preset mode with 10 patterns, a nocturnal mode to optimize battery life, and a “favorites”
mode that recalls your last 10 saved patterns (mode+adjustment). Either the speed, color
palette, brightness or preset patterns can be selected or adjusted in each mode. It charges
in 1-2 hours from USB power and most modes last all night or longer!
Installing the leash:
Your podpoi should come fully assembled. If you need to re-install your leash:
• pull the hard tri-ring o the tip of the pod to access the capsule – do NOT remove capsule from pod
• pull the silicone O-ring o the end of the capsule
• thread the end of your owleash through the tri-ring, then through the O-ring, then through the
hole in the capsule shell
• tie the end of the owleash in an overhand knot, tighten and
cut o excess
• use a lighter to melt the end of the knot, then the side of the lighter
to press the melted end into the knot, so it cannot come undone
• pull the leash tight, close the capsule, and reinstall the O-ring
• install the tri-ring back on the tip of the pod (see instructions below)
Assembling the tri-ring back onto the pod:
The podlight is designed with 3 petals that are held rmly together with the tri-ring.
To install the tri-ring:
• thread the tri-ring onto the leash
• place the leash between 2 of the petal-tips and insert
them all together into the ring
• align the two petals on one side of the ring to make
room for the third, and align the tips of the ring with
the seams between the petals
• pinch the tip of the third petal from the sides and push it inside the ring with the
other two petal tips – this step may seem dicult, but continue to massage the 3rd tip
into the ring. Don’t worry, you can’t break anything!
• all three tips should align perfectly and require signicant force to remove
• there should be no visible gaps and the leash should come out through the hole in the middle
BUTTON INTERFACE
There is a single recessed button on the bottom of the podlight. To turn on, press the
button – it will enter the pattern it was most recently in.
Select a mode: Press the button briey (short press), the light will blink and enter the
next mode. The last mode is o.
Adjust a mode: Hold the button for over half a second (long press), let go when the
light ashes, before it turns o. The mode will now cycle through its adjustment range.
When you like what you see, press the button once (short press) to select the adjust-
ment. You may also leave the podlight in “adjust” for a constantly changing eect :)
Turn o: There are 2 ways to turn o the podlight:
1. Hold the button until it turns o – about 1.5 sec (long hold) – the podlight will
blink and fade out. This records the last pattern you were in, and the pod will return
to it when you turn it back on. There is also a “favorites” mode that allows you to
select from the last 10 patterns you recorded.
2. You may also cycle through the modes until it turns o. This will reset the light
to mode1, default adjustment. All modes start in the default adjustment when you
change modes.
Micro-USB charging jack:
max. power-draw: 500mA
Length: 118mm | Diameter: 66mm | Weight: 128g | Battery: 3.7v, 750 mAh rechargeable Li-ion
Pod: silicone outer shell
Button: single recessed button
on bottom of pod
podpoi
TROUBLESHOOTING
1. The button is hard to press:
• is the c-ring installed properly on the capsule?
• is the capsule installed all the way into the pod?
• please refer to Assembly instructions above!
2. My pod does not charge or turn on, even when plugged in:
• check your power-source: try plugging in another pod or USB device to check the power source
• if you think your power source is good, but your pod still does not turn on, or blinks red when
unplugged and plugged in again, the battery may be deeply discharged. Leave it plugged in for
a few hours, and then unplug it and try again.
• if this doesn’t work, try a reset using the instructions that came with your podpoi (video instructions are
also available at youtube.com/owtoys - search for “podpoi reset”).
Find more podpoi instructional + troubleshooting videos at youtube.com/owtoys
Tip: To hang podpoi from your
belt, bag or hipsack, tie the leashes
together in a slip knot and clip a biner
through the loop! :)
Tip: Podpoi are not waterproof! But if you
drop them in water, it’s sometimes
possible to get them working again.
Open, rinse clean and dry ASAP! View a
video how-to at youtube.com/owtoys.
Loading...