FlowCon FT.0.3, FT.0.2, FT.0.4 Installation And Operation Instruction Manual
INSTALLATION AND OPERATION INSTRUCTION
1B95050 - P100006323
Brasil Singapore .
03/2014
FlowCon International assumes no responsibility for mistakes, if any, in any printed material.
Denmark Dubai USA
THERMAL ACTUA T ORSFlowCon FT actuators
- 1 -
FlowCon FT.0.2, FT.0.3 and FT.0.4 actuators
360º
Figure 2
Figure 1
A20625-00
FT.0.3
1403
MadeinGermany
230 V NC 1,2 W
A20625-00
FT.0.3
1403
MadeinGermany
230 V NC 1,2 W
A20625-00
FT.0.3
1403
MadeinGermany
230 V NC 1,2 W
A20625-00
FT.0.3
1403
MadeinGermany
230 V NC 1,2 W
A20625-00
FT.0.3
1403
MadeinGermany
230 V NC 1,2 W
>click<
The actuator type FlowCon FT.0.2 is a thermal mo-
dulating actuator, NC. FlowCon FT .0.3 and FT.0.4
are
thermal ON/OFF actuators, NC.
Fitting the FlowCon FT actuator:
Actuators are supplied with a separate black colored
adaptor ring. First, screw on the adaptor ring finger
tight to the connection thread at the top of the insert.
Do not use additional tools (figure 1,
and ). For
FlowCon FT.0.2 connect the cable before fitting the
actuator on to the adaptor ring. FlowCon FT.0.3 and
FT.0.4 comes with fixed cable and can be fitted immediately onto the adaptor ring (
). A click noise will
indicate that the actuator is fitted correctly (
).
Removing the FlowCon FT actuator:
Actuators are equipped with a front push button to
activate the release mechanism. When pushed, the
actuator is released and can be removed from the
adaptor ring. A special feature on the FlowCon FT.0.2
will allow the actuator to become tamper proof as the
bush button can be removed for protection.
Installation of the FlowCon FT actuator:
To ensure that the valve is in an open position during
commissioning of the system, all mentioned actuators
will be delivered in a Normally Open position and remain in this position until they are electrically operated first time. FIRST TIME POWERING requires operating voltage applied for approximately 6 minutes.
Upside down installation is allowed for all FT-actuators along with the standard horizontal and vertical
installation (figure 2).
Denmark Dubai USA
1B95050 - P100006323
Brasil Singapore .
03/2014
FlowCon International assumes no responsibility for mistakes, if any, in any printed material.
THERMAL ACTUA T ORSFlowCon FT actuators
- 2 -
Blue
Black
Red
FT .0.2 Actuator
Power 24V AC
Ground/common
0-10V DC
Blue
Brown
FT.0.3 / FT.0.4 Actuator
Power
Ground/common
24V AC/DC
230V AC
Open
Close
Figure 3
Connection and actuator wiring:
For power supply, use safety isolating transformer
according to EN 61558-2-6 (Europe) or class II
(North America) and for FlowCon FT.0.2 also with a
maximum power output of 100VA.
Wiring diagram for actuator type FT.0.2 (24V AC),
FT.0.3 (230V AC) and FT.0.4 (24V AC/DC) are shown
in figure 3.
Warranty obligation:
Failure to abide by all recommendations as per
this installation and operation instruction will void
warranty.
Loading...