Flotec E75STVT Owner's Manual

OWNER’S MANUAL

Submersible Solids
Handling Pumps

NOTICE D’UTILISATION

Pompes submersibles
pour les matières solides

MANUAL DEL USUARIO

Bombas submergibles para el
manejo de líquidos con sólidos

Installation/Operation/Parts

For further operating, installation,
or maintenance assistance:

Call 1-800-365-6832

English . . . . . . . . . . . . . . . Pages 2-6

Installation/Fonctionnement/Pièces

Pour plus de renseignements
concernant l’utilisation,
l’installation ou l’entretien,

Composer le

1 [phone]

Français . . . . . . . . . . . . Pages 7-11

Instalación/Operación/Piezas

Para mayor información sobre el
funcionamiento, instalación o
mantenimiento de la bomba:

Llame al 1-800-365-6832

Español . . . . . . . . . .Páginas 12-16

P.O. Box 342, Delavan, WI 53115

Phone:

1-800-365-6832

Fax:

1-800-526-3757

E-Mail:

[e-mail]

Web Site:

http://www.flotecwater.com

©2010 FP893 (Rev. 7/8/10)

Model E75STVT

5794 0308

Safety / Specifications / Performance / Installation 2

READ AND FOLLOW

SAFETY INSTRUCTIONS!

This is the safety alert symbol. When you see this

symbol on your pump or in this manual, look for
one of the following signal words and be alert to the
potential for personal injury:

warns about hazards that will cause serious

personal injury, death or major property damage if
ignored.

warns about hazards that can cause serious

personal injury, death or major property damage if
ignored.

warns about hazards that will or can cause

minor personal injury or property damage if ignored.
The label NOTICE indicates special instructions which

are important but not related to hazards.

Carefully read and follow all safety instructions in this
manual and on pump.

Keep safety labels in good condition.
Replace missing or damaged safety labels.

1. Read this manual carefully. Failure to follow these

instructions could cause serious bodily injury and/or
property damage.

2. Check your local codes before installing. You must

comply with their rules.

3. Vent sewage or septic tank according to local codes.

4. Do not install pump in any location classified as

hazardous by National Electrical Code, ANSI/NFPA
70-1990.

Hazardous voltage. Can shock, burn or

cause death. During operation, the pump is in water.

To avoid fatal shocks, proceed as follows if pump needs
servicing:

5A. Disconnect power to outlet box before unplugging

pump.

5B. Take extreme care when changing fuses or resetting

circuit breakers. Do not stand in water or put your
finger in fuse socket.

5C. Do not modify cord and plug. When using cord and

plug, plug into a grounded outlet only. When wiring
to a system control, connect pump ground lead to
system ground.

6. Do not run pump dry. Dry running can overheat
pump, (causing burns to anyone handling it) and will
void warranty.

7. Pump normally runs hot. To avoid burns when ser­vicing pump, allow it to cool for 20 minutes after
shut-down before handling it.

8. Motor has been filled at the factory with a special oil.
In normal service, motor should not need oiling.

This pump is designed for use in a residential sewage or
septic system only. Use only within design parameters.

NOTICE: This unit is not designed for use in a recirculat­ing system (such as a waterfall or fountain), or for appli­cations involving salt water or brine! Use with waterfalls,
fountains, ponds, salt water, or brine will void warranty.

Pump water only with this pump.
Do not use where water recirculates.
Not designed for use as a swimming pool drainer.

Read this owner’s manual for installation, operation, and
safety information.

INSTALLATION

(See Figure 1 for Typical Installation instructions.)

Pump must be level when operating. If

motor is tilted, internal start/run switch may overheat and
damage motor.

Risk of electrical shock. Can burn or kill.

Do not lift pump by power cord. See “Cord Lift Warning”
on Page 4. Do not hang pump from discharge pipe or
power cord.

1. Install the pump on a solid, level foundation, or in a
sump pit constructed of tile, concrete, steel or plas­tic. The recommended minimum diameter of the
sump pit is 18" (46cm) diameter and the minimum
recommended depth is 30" (76cm). Check local
codes for approved materials.

NOTICE: Pump should not be installed on clay, earth
or sand surfaces. Clean the area around the pump of
small stones and gravel which could clog the pump.
Keep the pump inlet screen clear.

GPH (LITERS) AT DISCHARGE FT. OF HEAD

5 (1.5m) 10 (3m) 15 (4.6m) 20 (6.1m) 24 (7.3m)

E75STVT 9200 (34,826) 7500 (28,391) 6300 (23,848) 2400 (9,085) 0 (0)

PERFORMANCE

FPSE Full Load Individual Branch Circuit Dual Element Time

Model H.P. Voltage Amps Required (Amps) Delay Fuse Amps

E75STVT 3/4 115 9.0 15 15

SPECIFICATIONS

For parts or assistance, call Flotec Customer Service at 1-800-365-6832