floorex SATELLITE 970-6 MkII Safety And Operators Manual & Parts Listing
FLOOREX PRODUCTS
1800 FLOOREX
SATELLITE 970-6 MkII
SAFETY & OPERATORS MANUAL AND
PARTS LISTING
22-03-11
Machine Weight Is 360kg including 2 X 15kg weights and 6 disks
SATELLITE 970-6 MkII
1800 FLOOREX
1800 356 673
PAGE 1.
TABLE OF CONTENTS
PAGE 1. TABLE OF CONTENTS
PAGE 2. SAFETY INSTRUCTIONS
PAGE 4. OPERATING INSTRUCTIONS
PAGE 5. AXLE HEIGHT ADJUSTMENT
PAGE 8. TOOLING REMOVAL
PAGE 9. WEIGHTS
PAGE 10. ELECTRICAL SAFETY
PAGE 12. PROBLEM SOLVING
PAGE 13. DIAMOND TOOLING SELECTION GUIDE
PAGE 15. WIRING DIGRAM
PAGE 16. PARTS LISTING
SATELLITE 970-6 MkII
1800 FLOOREX
1800 356 673
PAGE 2.
SAFETY INSTRUCTIONS
1. Read and understand the instructions on the machine and in this
manual and engine manual (if applicable). Different models may
have different parts and controls.
2. Equipment should only be operated by trained personnel, in good
physical condition and mental health (not fatigued). The operator
and maintenance personnel must physically be able to handle the
bulk weight and power of this machine.
3. This is a one person machine. Maintain a safe operating distance to
other personnel. Remember ‘one machine, one operator’.
4. This equipment is intended for commercial use.
5. For the operators’ safety and the safety of others, always keep all
guards and shrouds in place.
6. Never start or run machine when unattended.
7. This machine is intended for use on floor surfaces only.
8. Never start or run machine with handle folded or when disk(s) are
not in contact with the surface.
9. Do not lend or rent machine without the operating instructions for the
machine (and the engine, if applicable).
10. Wear clothing suitable for the job and for the work place including
safety shoes, hard hat, hearing protection, non fogging vented
safety goggles, and dust mask suitable for dust.
11. Keep body parts or any loose clothing away from moving parts.
Failure to comply could result in bodily injury.
SATELLITE 970-6 MkII
1800 FLOOREX
1800 356 673
PAGE 3.
SAFETY INSTRUCTIONS
12. Do not modify machine in any way. Only use genuine SATELLITE
parts and accessories.
13. Repairs should be performed by qualified persons only.
14. Ensure parts have stopped moving and disconnect power or spark
plug when servicing or changing blades or accessories.
15. Never operate machine in rain or if heavy moisture is present.
16. Petrol is extremely flammable and poisonous. Petrol should only be
dispensed in well ventilated areas, and only when engine is cool.
17. WARNING! POISONOUS EXHAUST GASES. Do not operate
petrol powered equipment without adequate ventilation. Carbon
monoxide is and invisible odorless gas that can harm or can kill you.
SATELLITE 970-6 MkII
1800 FLOOREX
1800 356 673
PAGE 4.
OPERATING INSTRUCTIONS
1. Wear clothes suitable for the job and for the work place including,
safety shoes, hard hat, hearing protection, non-fogging vented
safety goggles, and dust respirator suitable for dust.
2. WARNING! POISONOUS EXHAUST GASES. Do not operate
petrol powered equipment without adequate ventilation. Carbon
monoxide is an invisible odorless gas that can harm or can kill you.
3. Be sure all equipment is tested and tagged prior to use on any job.
4. Inspect entire area to be ground before grinding and remove any
bolts or concrete nails (etc) that could damage diamond tooling or
machine which could cause a hazardous situation.
5. Ensure there are no obstacles or existing structures that could
present a hazard to the operator. If so, take necessary action to
eliminate the hazard.
6. Fold handle into upright position (See ‘storage & diamond removal’,
following page) then tilt machine back so handle is resting on the
floor. (See figure 1c).
7. The machine takes a set of six (6) tools. Be sure the tools are of
even height.
8. Install appropriate diamond tooling or other available tooling into the
machine. Only use genuine SATELLITE tooling. Failure to comply
could result in bodily injury.
9. Tilt machine back onto the disk and unfold handle. (See operation
mode previous page)
SATELLITE 970-6 MkII
1800 FLOOREX
1800 356 673
PAGE 5.
AXLE HEIGHT ADJUSTMENT…
1. Axle Height should be set so that the level eye on the grinder is
centered when the machine is on a flat floor (not on a slope)
Loading...