Butterfly Valve
Product Training Presentation
Danfoss Flomatic Corporation
REV:082303
Butterfly Valve
SYLAX™
SERIES 149G BUTTERFLY VALVES
Wafer and Lug Type Butterfly Valve 2” trough 24”
Note: Other type and styles available 2” (50 mm) through 24” (600 mm)
SYLAX™
SERIES 149G BUTTERFLY VALVES
Technical Features:
MaterialDescription
Valve Body
Valve Disc
Valve Seat
Valve Shaft
Shaft Bushings
Top Flange
Face to face
Pressure rating
Temperature
rating
(EPDM Seat)
Cast Iron ASTM A126 Class GG25
Stainless Steel AISI 316 or Ductile Iron GGG40, Epoxy Coating
EPDM Standard or Buna-N and other seat material available
Stainless Steel AISI 420
PTFE lubricated plated steel
ISO 5211 standards
API 609 table1
(ISO 5752 class 20, DIN 3202 part 3 K1 BS 5155 table6 col.4)
200 PSI / 16 bar for ANSI 125/150 Flange
Working temp: Min +46°F (+8°C) Max +230°F (+110° C)
Design temperature rating: Min –4°F (-20°C) Max + 248°F (+120° C)
SYLAX™
SERIES 149G BUTTERFLY VALVES
SYLAX™
SERIES 149G BUTTERFLY VALVES
INSTALLATION
• The SYLAX butterfly valve is designed to be installed with ANSI 125#
or 150# flanges (flat faced or raised face flanges).
No gasket shall be used, SYLAX incorporates two “O”-ring seals on
the flange face.
• Before installing insure clean flange surfaces and proper pipe alignment.
• Center valve body within flange with bolts hand-tightened only.
Open valve disc slowly to insure free disc movement without restriction
from Internal diameters on both flange connections.
• Tighten bolts according to instructions and torque specifications.
Butterfly Valve
General installation in a pipe line
Butterfly Valve
Installation
Axial flow pumps – Pump shaft and valve stem are vertical.
Flow direction
Incorrect installation!
Butterfly Valve
Installation
Pipe Flange Connections
Misaligned
Pipe Flanges
Incorrect installation!
Pipe flanges are misaligned.
Butterfly disc edge will hit pipe flange
Resulting in valve damage and leakage.
Correct Installation
Pipe flanges are aligned and centered.
Butterfly Valve
Installation
Follow Flange Bolt Tightening Sequence
Start here and go 180°
NO GASKETS!
Butterfly Valve
Installation
Simple pipe flange connection
Incorrect installation!
This will result in seat distortion causing
high unseating torque problems.
Correct Installation
Butterfly “O” –ring seals centered
within pipe flanges.
Butterfly Valve
Installation
Locate butterfly valve stem vertical downstream of a pipe bend.
Flow down direction
Incorrect installation!
SYLAX™
SERIES 149G BUTTERFLY VALVES
O&M (Operating & Maintenance)
• Butterfly valves are pre-lubricated during manufacturing and no routine
lubrication is required.
• All butterfly valve parts are field replaceable and require no field
adjustments.
DISSASSEMBLY (and assembly)
• After pipe line have been depressurized and drained, remove butterfly
from line.
• Follow detailed Danfoss Flomatic instructions.
STORAGE
• It is good practice to store the SYLAX butterfly valve open with the handle
in the first position or a disc opening of about 10°.
Torque for NBRTorque for EPDM
SYLAX
BUTTERFLY
VALVE TORQUE
EPDM and NBR seat liner
Valve
Size
ANSI 125/150
PN6
(in pounds)
ANSI 250
PN16
(in pounds)
ANSI 125/150
PN6
(in pounds)
ANSI 250
PN16
(in pounds)
888888881
1331331331331 1/4
1331331331331 1/2
2121592121592
3102043102042 1/2
3542663542663
5844435844434
7616207616205
9747979747976
19471328194713288
300922573009225710
442533634425336312
637349566373495614
1106397368851796616
1593114161123911106318
2301219472159311416120
3097826552221271947224
Butterfly Valve
Installation
Booster System
Model C101
Automatic Control Valve
Full Lug Type
Butterfly Valve
Full Lug Type
Butterfly Valve
Butterfly Valve
Installation
Package Filter System
Model C101
Automatic Control Valve
Full Lug Type
Butterfly Valve
Full Lug Type
Butterfly Valve
Butterfly Valve
Operators and Actuators
Ten (10) position
Lockable handle
Is standard (2”-6”).
Top flange (ISO) allowing
Easy changing of operators.
Larger sizes are
Gear operated.
Butterfly Valve
Operators and Actuators
Gear operated butterfly valve
(Standard 8” and larger sizes)
Electric operated butterfly valve
(Several different Models and types)
Thank you.
Suggested Specifications AWWA Butterfly valves
Rubber Seated Butterfly Valve, Sizes 3 through 20 Inches:
General
Butterfly valves shall be manufactured in accordance with the latest revision of
AWWA C504, Class 150B and conform to NSF Standard 61. The manufacturer
shall have produced AWWA butterfly valves for a minimum of five years. All
valves shall be ______________ and comply with the following details.
Valve Bodies
Valve bodies shall be constructed of ASTM A126, Class B cast iron for flanged
valves or ASTM A48, Class 40 for wafer style. Flanged valves shall be fully
faced and drilled in accordance with ANSI Standard B16.1, Class 125.
Valve Seats
Rubber body seats shall be of one-piece construction, simultaneously molded
and bonded into a recessed cavity in the valve body. Seats may not be located
on the disc or be retained by segments and/or screws. For wafer style valves,
the seat shall cover the entire inner surface of the valve body and extend over
the outside face of the valve body to form a flange gasket.
Valve Bearings
Valve bearings shall be of a self-lubricating, nonmetallic material to effectively
isolate the disc-shaft assembly from the valve body. Metal-to-metal thrust
bearings in the flow stream are not allowed.
Suggested Specifications AWWA Butterfly valves
Valve Disc
The disc shall be a lens-shaped design to afford minimal pressure drop and line
turbulence. Materials of construction shall be:
· ASTM A126, Class B cast iron disc with a stainless steel type 316 edge
Discs shall be retained by stainless steel pins, which extend through the full
diameter of the shaft to withstand the specified line pressure up to valve rating and
the torque required to operate the valve. Disc stops located in the flow stream are
not allowed.
Valve Shafts
Valve shafts shall be of stainless steel type 304. At the operator end of the valve
shaft, a packing gland utilizing "V" type chevron packing shall be utilized. "O" ring
and "U" cup packing is not allowed.
Painting
All surfaces of the valve interior shall be clean, dry and free from grease before
painting. The valve surfaces except for disc edge, rubber seat and finished portions
shall be evenly coated with asphalt varnish in accordance with Federal Specification
TT-C-494 and AWWA Standard C504. The exterior valve surfaces and actuator
shall be evenly coated with a suitable primer to match field coatings.
Suggested Specifications AWWA Butterfly valves
Testing
Hydrostatic and seat leakage tests shall be conducted in strict accordance with
AWWA Standard C504.
Proof of Design
The manufacturer furnishing valves under the specification shall be prepared to
provide Proof of Design Test reports to illustrate that the valves supplied meet the
design requirements of AWWA C504.
Manual Actuators: Manual actuators shall be of the traveling nut, self-locking type
and shall be designed to hold the valve in any intermediate position between fully
open and fully closed without creeping or fluttering. Actuators shall be equipped
with mechanical stop-limiting devices to prevent overtravel of the disc in the open
and closed positions. Actuators shall be fully enclosed and designed to produce the
specified torque with a maximum pull of 80 lbs. on the handwheel or chainwheel.
Actuator components shall withstand an input of 450 ft. lbs. at extreme operator
position without damage. Manual actuators shall conform to AWWA C504 and shall
be Pratt MDT or an approved equal.
Power Actuators: Refer to Cylinder suggested specifications and detailed
information regarding cylinder actuators. For electric actuators, see electric
actuator specification.
Loading...