flir.com/security/pro
MODEL: N243MW2
SERIES
QUICK START GUIDE
English Version 1.0
FLIR Systems, Inc., Copyright © 2016
As our products are subject to continuous improvement, FLIR Systems
Inc. reserves the right to modify product design, specifications and
prices, without notice and without incurring any obligation. E&OE
2MP Micro Vandal
Network Dome Camera
flir.com/security/pro
VISIT
Compatible Accessories
IT’S ALL ON THE WEB!
FCC Notice
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
N243MW2_QSG_EN_R1
This security camera has several mounting options:
Safety Precautions
• Use an appropriate low-voltage power cable to prevent fire
or electrical shock.
• Make sure to install the camera in an area that can support
the camera weight.
• There are no user-serviceable parts inside the camera. Do
not disassemble the camera.
• Do not clean the lens cover with an abrasive cleaning
material. Use a soft cloth to clean the lens cover.
• Camera is rated for outdoor use (IP66), but is not intended
for submersion in water.
• Extend the Ethernet cable run for your camera up to 300ft.
You can use an RJ45 coupler or network switch to connect
male ends of Ethernet cable together. A maximum of 3
connections is recommended.
Weights & Dimensions
0.78lbs / 0.35kg
Weight
Accessories Model Numbers
Junction Box S4JF5G
Wall Mounts S1WA1G
Corner Mounts S4JF5G with S1RA2G
Pole Mounts S1WA1G with S4PA2G or
S4JF5G with S1PA2G
Cap housing
RJ45 plug
Outer seal
Inner
seal
Cap-sealing nut
Ethernet
connector
Using the RJ45 Cap (Optional)
ATTENTION:
The supplied RJ45 cap is weather-resistant. Seal the cap with
silicone if it will be exposed to precipitation regularly.
1
2
3
4
Fit the outer seal over your camera’s Ethernet connector
and insert the inner seal into the cap housing.
Run the stripped end of an Ethernet cable through the
parts of the RJ45 cap, as shown above.
Terminate the Ethernet cable with an RJ45 plug, and plug
the cable into your camera’s Ethernet connector.
5
Screw the cap housing onto the Ethernet connector.
Screw the cap-sealing nut tightly into the cap
housing.
1.4”/35mm
2.0”/50mm
4.0”/
106mm
N243MW2_QSG_EN_R1.indd 1 9/27/2016 11:45:06 AM
Package Contents
• 1× 2MP Micro Vandal Dome Camera
• 4× Mounting Screws & Drywall Anchors
• 1× Allen Key
• 1× Mounting Template
• 1× RJ45 Cap
A
B
C
Connecting the Camera
A
B
Power Input: If not using PoE,
connect the camera to a 12V DC power
source (420mA or higher required).
Ethernet Connector: Connect the
camera to an NVR or a router or
switch on your network using
CAT5e or better Ethernet cable (not
included). PoE supported (802.3af).
NOTE: For instructions on
weatherproofing the Ethernet
connection, see “Using the
RJ45 Cap (Optional)” on reverse.
A B
Disabling Camera Audio
A
B
In Live view, click the camera channel to open in fullscreen. Right-click and then click Main Menu. Enter the
system user name and password if prompted.
Audio is enabled by default. To disable camera audio through
an NVR:
C
Click and select RECORDING.
Uncheck the checkbox to disable audio for Main
Stream.
Click Apply to save your changes.
D
Under Channel, select the camera you would like to
configure.
Configure the following:
1
2
3
4
5
Under Type, select Continuous.
You can also disable audio and video for Sub
Stream. Uncheck the check box to disable audio for
Sub Stream
Uncheck the check box to disable video for Sub
Stream
6
1
2
3
4
5
6
Click OK when finished.
Use the included Allen key to loosen the dome cover
screws (2×). Remove the dome cover.
ATTENTION:
Test the camera prior to selecting a permanent mounting location by
temporarily connecting the camera(s) and cables to the NVR.
Installing the Camera
1
Use the included mounting template to mark holes for
the mounting screws and camera cable.
2
3
4
5
10
Drill holes for the mounting screws and camera cable.
NOTE: Use the included drywall anchors if needed.
Connect cables as shown in the section “Connecting the
Camera”.
Attach the camera base to the mounting surface using
the included mounting screws (4×).
Camera Overview
N243MW2_QSG_EN_R1
C
A. Lens Module Adjustment
Screw
B. Lens Holder
C. Lens Module
D. Camera Base
E. Mounting Screw Holes (4×)
F. Built-in Microphone
G. microSD Card Slot:
Insert a microSD card
(not included) into the
slot. microSD card Class
10 supported.
H. Reset Button: Press
and hold the button
for 5 seconds to reset
the camera to default
settings.
6
Remove the vinyl film from the dome cover when your
installation is complete.
Use a Philips head screwdriver (not included) to loosen
the lens module adjustment screw. Do not loosen all the
way.
7
Adjust the angle of the camera as needed.
A) Turn the lens holder up to 45°
B) Tilt the lens module up to 90°
C) Rotate the lens module 360°
8
Tighten the lens module adjustment screw when
finished.
9
Cover the camera base with the dome cover and tighten
the screws on either side of the dome cover.
Mounting Surface
Mounting Template
Drywall
Anchors
(4×)
Mounting Screws (4×)
Dome Cover
Dome Cover
Screws (2×)
Lens
Holder
Lens
Module
Lens Module
Adjustment
Screw
A
B
E
F
H
Camera
Base
D
G
I
J
I. Dome Cover
J. Dome Cover Screws (2×)
ATTENTION:
Audio recording without consent is illegal in certain jurisdictions. FLIR Systems, Inc.
assumes no liability for use of its products which fails to conform with local laws.
NOTE: Video must be enabled for Sub Stream to
enable/disable audio.
NOTE: You must disable audio for all recording types
under the Type drop-down list. Repeat the above steps
to disable camera audio for all recording types.
N243MW2_QSG_EN_R1.indd 2 9/27/2016 11:45:08 AM
Loading...