How it Works
Flir Displays
Loading...
VS70
Brochure
11 pgs3.04 Mb0
Data Sheet
2 pgs220.32 Kb0
Users Manual
36 pgs556.02 Kb0
Table of contents
Loading...

Flir Displays VS70 Users Manual

Download
User’s manual
FLIR VS70
High definition videoscope inspection camera
User’s manual
FLIR VS70
#T559827; r. AC/ 9135/9135; en-US
Table of contents
1 Disclaimers. . ... ... . .. . .. . .. . ... ... . .. . .. . ... ... . .. . .. . ... ... ... . .. . .. . .. 1
2 Safety information . ... ... ... . .. . .. . ... ... . .. . .. . ... ... ... . .. . .. . ... ... . . 4
3 Introduction . . ... ... . .. . .. . ... ... ... . .. . .. . ... ... . .. . .. . ... ... ... . .. . .. . . 6
4 Description . .. . ... ... . .. . .. . ... ... . .. . .. . ... ... ... . .. . .. . ... ... . .. . .. . ... 7
4.2 Articulating probe . ... . .. . .. . ... ... ... . .. . .. . ... ... . .. . .. . ... ..10
4.3 Wireless transmitter ... ... ... . .. . .. . ... ... . .. . .. . ... ... ... . .. .11
4.4 Probe accessories ... . .. . ... ... ... . .. . .. . ... ... . .. . .. . ... ... . .11
4.5 Probe. ... ... . .. . .. . ... ... . .. . .. . ... ... . .. . .. . ... ... . .. . .. . ... ..12
5 Operation ... . .. . .. . ... ... . .. . .. . ... ... . .. . .. . ... ... ... . .. . .. . ... ... . .. . .13
5.1 Basic operation . .. . .. . ... ... . .. . .. . ... ... ... . .. . .. . ... ... . .. . .13
5.2 Setup menu . ... . .. . .. . ... ... . .. . .. . ... ... ... . .. . .. . ... ... . .. . .14
5.3 Installing probe accessories. ... . .. . .. . ... ... . .. . .. . ... ... . .. .15
5.4 Articulating probe . ... . .. . .. . ... ... ... . .. . .. . ... ... . .. . .. . ... ..15
5.5 Wireless transmitter ... ... ... . .. . .. . ... ... . .. . .. . ... ... ... . .. .17
5.6 Managing stored pictures and videos.. ... ... . .. . ... ... ... . .. 19
5.7 Video output to a TV or external monitor ... . .. . .. . ... ... . .. . .21
5.8 Reset.. ... ... . .. . .. . ... ... . .. . .. . ... ... . .. . .. . ... ... ... . .. . .. . .21
5.9 Rear stand . .. . ... ... . .. . .. . ... ... . .. . .. . ... ... . .. . .. . ... ... ... 21
6 Maintenance. .. . .. . ... ... . .. . .. . ... ... . .. . .. . ... ... ... . .. . .. . ... ... . .. . .22
6.1 Cleaning . . .. . ... ... ... . .. . .. . ... ... . .. . .. . ... ... ... . .. . .. . ... .22
6.2 Battery recharging . . ... ... ... . .. . .. . ... ... . .. . .. . ... ... ... . .. .22
7 Technical specifications . ... ... . .. . .. . ... ... . .. . .. . .. . ... . .. . .. . .. . ...23
7.1 Monitor ... ... ... . .. . .. . ... ... . .. . .. . ... ... . .. . .. . ... ... ... . .. . .23
7.2 Transmitter . ... ... . .. . .. . ... ... ... . .. . .. . ... ... . .. . .. . ... ... ... 24
7.3 Camera . . .. . .. . ... ... . .. . .. . ... ... ... . .. . .. . ... ... . .. . .. . ... ..24
7.4 Probes and cameras . . .. . ... ... . .. . .. . ... ... . .. . .. . ... ... ... .25
7.5 Earphone . . ... ... . .. . .. . ... ... ... . .. . .. . ... ... . .. . .. . ... ... . .. 25
#T559827; r. AC/ 9135/9135; en-US v
Table of contents
7.6 Part numbers .. ... . .. . .. . ... ... . .. . .. . ... ... ... . .. . ... ... ... . .25
8 Technical support ... ... . .. . .. . ... ... . .. . .. . ... ... ... . .. . .. . ... ... . .. . .27
9 FLIR Test and Measurement Limited 2 Year Warranty .. . .. . ... ... .28
#T559827; r. AC/ 9135/9135; en-US vi

1 Disclaimers

1.1 Copyright

© 2013, FLIR Systems, Inc. All rights reserved worldwide. No parts of the soft­ware including source code may be reproduced, transmitted, transcribed or translated into any language or computer language in any form or by any means, electronic, magnetic, optical, manual or otherwise, without the prior written per­mission of FLIR Systems.
The documentation must not, in whole or part, be copied, photocopied, repro­duced, translated or transmitted to any electronic medium or machine readable form without prior consent, in writing, from FLIR Systems.
Names and marks appearing on the products herein are either registered trade­marks or trademarks of FLIR Systems and/or its subsidiaries. All other trade­marks, trade names or company names referenced herein are used for identification only and are the property of their respective owners.

1.2 Quality assurance

The Quality Management System under which these products are developed and manufactured has been certified in accordance with the ISO 9001 standard.
FLIR Systems is committed to a policy of continuous development; therefore we reserve the right to make changes and improvements on any of the products without prior notice.

1.3 Documentation updates

Our manuals are updated several times per year, and we also issue product-crit­ical notifications of changes on a regular basis.
To access the latest manuals and notifications, go to the Download tab at:
http://support.flir.com
It only takes a few minutes to register online. In the download area you will also find the latest releases of manuals for our other products, as well as manuals for our historical and obsolete products.
#T559827; r. AC/ 9135/9135; en-US 1
1 Disclaimers

1.4 Disposal of electronic waste

As with most electronic products, this equipment must be disposed of in an envi­ronmentally friendly way, and in accordance with existing regulations for elec­tronic waste.
Please contact your FLIR Systems representative for more details.

1.5 FCC Complicance

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal­lation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter­mined by turning the equipment off and on, the user is encouraged to try to cor­rect the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
#T559827; r. AC/ 9135/9135; en-US 2
1 Disclaimers
WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

1.6 Industry Canada compliance

This device complies with Industry Canada licence-exempt RSS standard(s). Op­eration is subjectto the following two conditions: (1) this device may not cause in­terference, and (2) this devicemust accept any interference, including interference that may cause undesired operation of thedevice.
#T559827; r. AC/ 9135/9135; en-US 3

2 Safety information

Note
Before operating the device, you must read, understand, and follow all in­structions, dangers, warnings, cautions, and notes.
Note
FLIR Systems reserves the right to discontinue models, parts or accessories, and other items, or to change specifications at any time without prior notice.
Note
Remove the batteries if the device is not used for an extended period of time.
WARNING
Make sure that children cannot touch the device. The device contains danger­ous objects and small parts that children can swallow. If a child swallows an object or a part, speak with a physician immediately. Injury to persons can occur.
WARNING
Do not let children play with the batteries and/or the packing material. These can be dangerous for children if they use them as toys.
WARNING
Do not touch expired or damaged batteries without gloves. Injury to persons can occur.
WARNING
Do not cause a short-circuit of the batteries. This can cause damage to the in­strument and can cause injury to persons.
#T559827; r. AC/ 9135/9135; en-US 4
2 Safety information
WARNING
Do not put the batteries into a fire. Injury to persons can occur.
CAUTION
For the Articulating Probe, do not operate the articulation knob with the probe in a coiled configuration. This will cause damage to the articulation controls.
This symbol, adjacent to another symbol or terminal, indicates that the user must refer to the manual for further information.
This symbol, adjacent to a terminal, indicates that, under normal use, hazardous voltages may be present.
Double insulation.
#T559827; r. AC/ 9135/9135; en-US 5

3 Introduction

Congratulations on your purchase of this FLIR VS70 video boroscope.
This instrument is designed for use as a remote inspection device. It can be used to peer into tight spots, and record and playback real-time video and images. Typical applications include HVAC inspection, cable routing, and automotive/ boat/aircraft inspection. The monitor is designed with dual left- or right-handed controls for maximum flexibility, and is available with a full line of accessories.
This boroscope is shipped fully tested and, with proper use, will provide years of reliable service.
#T559827; r. AC/ 9135/9135; en-US 6

4 Description

4.1 Monitor

Figure 4.1 Monitor front view
1. Function buttons, see section 4.1.1 Function buttons, page 9.
2. Display.
#T559827; r. AC/ 9135/9135; en-US 7
4 Description
Figure 4.2 Monitor rear view
1. Probe connector.
2. Rear stand.
Figure 4.3 Monitor bottom view, with access cover removed
1. USB connector.
2. Reset button.
3. SD card slot.
4. Video output jack.
5. Earphone jack.
6. AC adapter connector.
#T559827; r. AC/ 9135/9135; en-US 8
4 Description
4.1.1 Function buttons
For two-camera probes, press the button to toggle between the side view and the front view camera lens.
• Press the button to take a picture.
• Press and hold down the button for 3 seconds to start/stop re­cording a video.
Press the button to rotate the display 90°.
Press the buttons to increase/decrease the display resolution.
Press the buttons to increase/decrease the camera LED light intensity.
Press and hold down the button for 5 seconds to switch on/off the monitor.
• Press the buttons to navigate up/down in the setup menu.
• Press the
• Press the button to open the setup menu.
• Press the button to select the highlighted menu item.
Press the button to exit the setup menu.
button to access the picture/video memory.
4.1.2 Display icons
Indicates that a picture is being taken.
Indicates that a video is being recorded.
Indicates the battery voltage status.
#T559827; r. AC/ 9135/9135; en-US 9
4 Description
Indicates that a stored picture is being displayed.
Indicates that a stored video is being displayed.
Indicates playback of a stored video.
Indicates paused playback of a stored video.

4.2 Articulating probe

Figure 4.4 Articulating probe
1. Articulation knob (up/down).
2. Articulation knob (left/right).
3. Tension knob (left/right).
4. Articulating camera.
5. Tension knob (up/down).
6. Light intensity buttons.
7. Power button.
8. AC adaptor and extension cable sockets.
#T559827; r. AC/ 9135/9135; en-US 10
4 Description

4.3 Wireless transmitter

Figure 4.5 Wireless transmitter
1. Probe connector.
2. Light intensity buttons.
3. Power button.
4. AC adaptor and extension cable sockets.

4.4 Probe accessories

Figure 4.6 Probe accessories
1. Anti-snag tip.
2. Magnet.
3. 45° mirror.
#T559827; r. AC/ 9135/9135; en-US 11
4 Description

4.5 Probe

Figure 4.7 Probe
1. Camera.
2. Shaft.
3. Monitor connector.
#T559827; r. AC/ 9135/9135; en-US 12

5 Operation

5.1 Basic operation

1. Insert an SD card into the SD card slot, located on the bottom of the monitor.
2. Connect the probe to the monitor.
3. Press and hold down the
monitor.
4. If the battery indicator monitor does not power on, replace the battery. See section 6.2 Battery re- charging, page 22.
5. Maneuver the probe into position to view the area to be examined. The probe can be bent into the shape of the area to be examined. The optimum focus distance is probe dependent: typically 2–6 cm (0.79–2.3″).
6. For two-camera probes, press the view and the front view camera lens.
7. Use the
5.1.1 Controlling the camera LED light intensity
Note
The camera LEDs become warm when set to maximum intensity.
1. In wireless mode, use the light intensity buttons on the articulating probe (see Figure 4.4 Articulating probe, page 10) or wireless transmitter (see Fig­ure 4.5 Wireless transmitter, page 11) to increase/decrease the light intensity.
2. In direct mode, use the light intensity.
5.1.2 Taking a picture
1. Press the icon is briefly displayed.
5.1.3 Recording a video
1. Audio can be recorded on the video via the microphone, located on the bot­tom of the monitor. For audio recording, remove the bottom access cover.
and buttons to zoom in and out.
button to take a picture and store it in the memory. The
button for 5 seconds to switch on the
shows that the battery voltage is low or if the
button to toggle between the side
and buttons to increase/decrease the
#T559827; r. AC/ 9135/9135; en-US 13
5 Operation
2. Press and hold down the button for 3 seconds (long press) to start the
video recording. The
3. While recording, you can take a picture by pressing the
icon is displayed.
button (short
press).
4. Press and hold down the
button for 3 seconds (long press) to stop the
video recording.

5.2 Setup menu

Monitor settings are adjusted in the setup menu.
DELETE ALL Delete all stored pictures and videos.
VIDEO OUTPUT For two-camera probes, select the front view or the
side view camera.
DATE/TIME SETUP Select the date and time format, set the date and
time, and select display on/off (when on, the date and time are shown on the display and on the pic­tures/videos).
LANGUAGE Select the menu display language.
VIDEO FORMAT Set the video output to NTSC or PAL format.
AUTO POWER OFF Set auto power off to 5, 10, 15, or 30 minutes or
DISABLE.
INPUT SOURCE Set the input source to DIRECT or WIRELESS.
1. Press the
2. Press the
3. Press the
4. Press the
button to open the setup menu.
or button to navigate to the desired menu item.
button to select the highlighted menu item.
or button to scroll through the options in an open menu
item.
5. Press the
#T559827; r. AC/ 9135/9135; en-US 14
or button to increase/decrease the selected value.
5 Operation
6. After a change, do one of the following:
• Press the
• Press the
button to save the changed value.
button to exit without saving.
Note
After 10 seconds of inactivity, the setup menu will exit without saving any changes.
7. Press the
button to move up one step in the menu hierarchy and to exit
the setup menu.

5.3 Installing probe accessories

Three accessories (mirror, anti-snag tip, and magnet) are supplied with each probe.
Figure 5.1 Installing probe accessories
1. Unscrew the probe ring.
2. Screw on the accessory.

5.4 Articulating probe

The articulating probe, with an adjustable tip angle, is used for improved viewing angles and optimum inspection when the probe is inserted into the area to be ex­amined. The articulating probe is available in a direct (wired) or wireless version.
Turn the articulation knobs to adjust the camera tip. The tension of an articulation knob is adjusted by turning the corresponding tension knob. Refer to Figure 4.4 Articulating probe, page 10.
#T559827; r. AC/ 9135/9135; en-US 15
5 Operation
Note
Do not operate the articulation knobs (see Figure 4.4 Articulating probe, page
10) with the probe in a coiled configuration. This will damage the articulation controls.
5.4.1 Articulating probe—wireless version
Note
The articulating probe battery must be fully charged for wireless operation. A weak battery may result in shut down of the articulating probe.
1. Connect the AC adaptor to the articulating probe and charge the battery.
2. On the monitor, press and hold down the
button for 5 seconds to
switch on the monitor.
3. In the setup menu under INPUT SOURCE, select WIRELESS. Refer to sec­tion 5.2 Setup menu, page 14.
4. On the articulating probe, press and hold down the
button for 5 sec­onds to switch on the articulating probe. The camera video is displayed on the monitor display.
#T559827; r. AC/ 9135/9135; en-US 16
5 Operation
5. Insert the probe into the area to be examined. Adjust the camera tip to the re­quired viewing angle.
5.4.2 Articulating probe—direct version
1. Connect the articulating probe to the probe connector on the monitor, using the supplied patch cable.
2. On the articulating probe, press and hold down the
button for 5 sec­onds to switch on both the articulating probe and the monitor. The camera video is displayed on the monitor display.
3. In the setup menu under INPUT SOURCE, select DIRECT. Refer to section
5.2 Setup menu, page 14.
4. Insert the probe into the area to be examined. Adjust the camera tip to the re­quired viewing angle.

5.5 Wireless transmitter

The wireless transmitter is intended for use in areas that are difficult to access or in situations where it is hard to maneuver the probe with the display attached. The wireless transmitter can also be connected directly to the monitor using the patch cord.
#T559827; r. AC/ 9135/9135; en-US 17
5 Operation
5.5.1 Wireless transmitter—wireless version
Note
The wireless transmitter battery must be fully charged for wireless operation. A weak battery may result in shut down of the transmitter.
1. Connect the AC adaptor to the wireless transmitter and charge the battery.
2. Attach the probe to the wireless transmitter.
3. On the monitor, press and hold down the
button for 5 seconds to
switch on the monitor.
4. In the setup menu under INPUT SOURCE, select WIRELESS. Refer to sec­tion 5.2 Setup menu, page 14.
5. On the wireless transmitter, press and hold down the
button for 5 sec­onds to switch on the transmitter. The camera video is displayed on the mon­itor display.
#T559827; r. AC/ 9135/9135; en-US 18
5 Operation
5.5.2 Wireless transmitter—direct version
1. Attach the probe to the wireless transmitter.
2. Connect the wireless transmitter to the probe connector on the monitor, us­ing the supplied patch cable.
3. On the wireless transmitter, press and hold down the
button for 5 sec­onds to switch on both the transmitter and the monitor. The camera video is displayed on the monitor display.
4. In the setup menu under INPUT SOURCE, select DIRECT. Refer to section
5.2 Setup menu, page 14.

5.6 Managing stored pictures and videos

5.6.1 Viewing pictures and videos on the monitor display
1. Press the
2. Thumbnails of the pictures and videos are displayed. The
button to access the pictures and videos in the memory.
icon is dis-
played on video thumbnails.
3. Use the
and buttons to navigate through the picture/video thumb-
nails. The selected picture/video is framed.
#T559827; r. AC/ 9135/9135; en-US 19
5 Operation
4. To open the selected picture/video file, press the
The file number (e.g., IMG00005) and the
button.
icon (for pictures) or the
icon (for videos) are displayed.
5. To start playback of an open video file, press the
button. The icon
is displayed.
6. To pause the playback of a video, press the
button. The icon is
displayed.
7. To exit an open picture/video, press the
8. To exit the picture/video file memory, press the
button.
button.
5.6.2 Transferring files to a PC
There a two methods for transferring stored picture/video files to a PC:
• Remove the SD card from the monitor and insert it into the PC.
• Connect the monitor to the PC with a USB cable.
Pictures are saved in *.JPG format and videos in *.AVI format.
5.6.3 Deleting the picture/video memory
1. In the setup menu, select DELETE ALL. Refer to section 5.2 Setup menu,
page 14.
The ERASE YES/NO box appears.
2. Press the
button to select YES. Press the button to delete all files
in the memory.
Press the
#T559827; r. AC/ 9135/9135; en-US 20
button to exit without deleting the file.
5 Operation

5.7 Video output to a TV or external monitor

The monitor can be set to output the high-quality video to a TV or other external video monitor.
1. In the setup menu under VIDEO FORMAT, select PAL or NTSC to match the TV/external monitor to be used. Refer to section 5.2 Setup menu, page 14.
2. Connect the video cable to the video output jack, located on the bottom of the monitor. Connect the other end of the cable to the video input jack of the TV or other external monitor.
The high-quality video image is displayed on the TV/external monitor.

5.8 Reset

If the monitor becomes unresponsive due to electromagnetic interference or oth­er magnetic event, use a paper clip or other narrow object to press the Reset but­ton, located on the bottom of the monitor.

5.9 Rear stand

The rear stand can be set to three positions: lower position (stored), middle posi­tion for bench viewing, and upper position for hanging.
#T559827; r. AC/ 9135/9135; en-US 21

6 Maintenance

6.1 Cleaning

Clean the monitor, articulating probe, wireless transmitter, and accessories with a damp cloth and mild detergent; do not use abrasives or solvents.

6.2 Battery recharging

1. Ensure that the monitor is switched off.
2. Connect the AC adaptor to the monitor.
3. After several hours, press the
The battery voltage status is indicated on the display:
• The battery is fully charged:
• The battery charging is still in process:
4. If the battery is fully charged, remove the AC adaptor and observe that the
fully charged four-bar indicator appears:
5. If the battery is not fully charged, press the monitor and continue charging.
Note
The battery will not charge properly if the monitor is switched on during the charging cycle.
button to switch on the monitor.
.
.
.
button to switch off the
#T559827; r. AC/ 9135/9135; en-US 22

7 Technical specifications

7.1 Monitor

LCD screen 145 mm (5.7″); viewable: 135 mm
Interface Mini USB 1.1 and AV out
Recording medium SD card
SD memory 4 GB standard (32 GB maximum)
Compression format MPEG4
Still image format JPEG (640 × 480)
Video recording format AVI (640 × 480)
Video output format NTSC and PAL; Frame rate 30 fps
Receiver frequency 2.4 GHz
Receiver sensitivity –87 dBm (SNR = 42 dB, F
Video system NTSC/PAL
Data
Audio type
Tripod mount On rear, accepts standard tripod
Battery 3.7 V rechargeable lithium polymer
Power adaptor 100–240 V input/5 V DC output
Operating temperature –10 to 60℃ (14 to 140℉)
Storage temperature –40 to 80℃ (–40 to 176℉)
Operating humidity (maximum)
(5.3″)
Active matrix, 640 × 480 pixels
mod
kHz)
Video/audio
Stereo
screw
80%
= 15
#T559827; r. AC/ 9135/9135; en-US 23
7 Technical specifications
Dimensions (W × D × H) 241 mm × 178 mm × 70 mm (9.5″ ×
7″ × 2.75″)
Weight 1.57 kg (3.46 lb.), including batteries

7.2 Transmitter

Frequency
2.4 GHz
Data Video/audio
Video system NTSC/PAL
Battery 3.7 V rechargeable lithium polymer
Power adaptor
100–240 V input/9 V DC output
Unobstructed effective range 10 m (32.5′)
Operating temperature –10 to 60℃ (14 to 140℉)
Storage temperature –40 to 80℃ (–40 to 176℉)
Dimensions (W × D × H) 190 mm × 70 mm × 63.5 mm (7.5″ ×
2.75″ × 2.5″)
Weight (approximate) 0.43 kg (0.95 lb)

7.3 Camera

Imaging Sensor CMOS
Video Format NTSC
Brightness Control Manual
Lamp Type LED
Interface Composite video
Operating Temperature –10℃ to 50℃ (14 to 122℉)
#T559827; r. AC/ 9135/9135; en-US 24
7 Technical specifications

7.4 Probes and cameras

Articulation 240 ± 20° manual tip articulation
Accessories Mirror, magnet and anti-snag ball (ex-
cluding 25 mm diameter cables)

7.5 Earphone

Plug
• 3.5 mm (0.14″)
• 4 rings
Speaker
• 15 mm (0.59″)
• 32 Ω
• 20~20 kHz
Microphone 6 × 5 mm (0.24″ × 0.2″)
Boom microphone, total length 10 cm (3.9″)
Color Black
Wire length 1.2 m (3.9′)

7.6 Part numbers

Part number Description
VST Wireless 2.4 GHz VS70 transmitter
VSA2-1-w Wireless 2-way 6 mm (0.24″) articulating camera
with 1 m (3.3′) probe
VSA2-2-w Wireless 2-way articulating camera with 2 m (6.6′)
probe
VSA2-1 2-way 6 mm (0.24″) articulating camera with 1 m
(3.3′) probe
VSA2-2 2-way 6 mm (0.24″) articulating camera with 2 m
(6.6′) probe
#T559827; r. AC/ 9135/9135; en-US 25
7 Technical specifications
Part number Description
VSC3.9-1FM 3.9 mm (0.15″) camera with 1 m (3.3′) flexible
probe – QVGA via SF
VSC4.1-2RM 4.1 mm (0.16″) camera with 2 m (6.6′) SR probe –
QVGA via SF
VSC5.8-1RM 5. 8 mm (0.23″) camera with 1 m (3.3′) SR probe –
VGA via SF
VSC5.8-2RM 5.8 mm (0.23″) camera with 2 m (6.6′) SR probe –
VGA via SF
VSC5.8-1R 5.8 mm (0.23″) camera with 1 m (3.3′) SR probe –
VGA via LF
VSC5.8-2R 5.8 mm (0.23″) camera with 2 m (6.6′) SR probe –
VGA via LF
VSC5.8-20 5.8 mm (0.23″) camera with 20 m (66′) FG probe –
VGA via LF
VSC5.8-30 5.8 mm (0.23″) camera with 30 m (98′) FG probe –
VGA via LF
VSC8.0-1R 8 mm (0.31″) camera with 1 m (3.3′) SR probe –
VGA via LF
VSC8.0-2R 8 mm (0.31″) camera with 2 m (6.6′) SR probe –
VGA via LF
VSC6.5-12S 6.5 mm (0.26″) camera with 0.30 m (12″) SS rigid
probe – VGA via SF
VSC6.5-17S 6.5 mm (0.26″) camera with 0.43 m (17″) SS rigid
probe – VGA via SF
VSS-20 Plumbing spool 20 m (66′)
VSS-30 Plumbing spool 30 m (98′)
VSC25 25 mm (0.98″) camera with FG detachable probe –
VGA via LF
VSC28 28 mm (1.1″) camera with FG detachable probe –
VGA via LF
#T559827; r. AC/ 9135/9135; en-US 26

8 Technical support

Website http://www.flir.com/test
Technical support T&MSupport@flir.com
Repairs Repair@flir.com
#T559827; r. AC/ 9135/9135; en-US 27

9 FLIR Test and Measurement Limited 2 Year Warranty

A qualifying FLIR Test and Measurement product (the “Product”) purchased either directly from FLIR Commer­cial Systems Inc and affiliates (FLIR) or from anauthor­ized FLIR distributor or reseller that Purchaser registers on-line with FLIR is eligible forcoverage under FLIR’s Lim­ited Warranty, subject to the terms and conditions in this document. This warranty onlyapplies to purchases of Qualifying Products (see below) purchased and manufac­tured after April 1, 2013.
PLEASE READ THIS DOCUMENTCAREFULLY; ITCON­TAINS IMPORTANT INFORMATION ABOUT THE PROD­UCTS THAT QUALIFY FOR COVERAGEUNDER THE LIMITED WARRANTY, PURCHASER’S OBLIGATIONS, HOW TO ACTIVATE THEWARRANTY, WARRANTY COVERAGE, AND OTHERIMPORTANT TERMS, CON­DITIONS, EXCLUSIONS AND DISCLAIMERS.
1. PRODUCT REGISTRATION. To qualify forFLIR’s Lim-
ited Warranty, Purchaser must fully register the Product di­rectly with FLIR on-line at http://www.flir.com within Sixty (60) DAYS of the date the Product was purchased bythe first retail customer (the “Purchase Date”). Qualifying PRODUCTS THAT ARE NOTREGISTERED ON-LINE WITHIN SIXTY (60) DAYS OF THE PURCHASE DATE WILL HAVE A LIMITEDONE YEAR WARRANTY FROM DATE OF PURCHASE.
2. QUALIFYING PRODUCTS. Uponregistration, Test and
Measurement products that qualify for coverage under FLIR’s Limited Warrantyare: VS70 Videoscope, VSAxx Articulation Camera, VSCxx Camera, VSSxx Probe Spool, VST handset, MR02 Pin Extension Probe,and TAxx not including accessories which may havetheir own warranty.
3. WARRANTY PERIODS. Theapplicable LimitedWar-
ranty Period measured from the Purchasedata are:
Products Limited Warranty
VS70, VSAxx, VSCxx, VSSxx, VST, MR02, TAxx
Any Product that is repaired or replaced under warranty is covered under this Limited Warrantyfor one hundred eighty days (180) daysfrom the date of return shipment by FLIR or for the remaining duration ofthe applicable Warranty Period, whichever is longer.
4. LIMITED WARRANTY. In accordance with theterms
and conditions of this Limited Warranty, and except as ex­cluded or disclaimed in this document, FLIR warrants, from the Purchase Date, that all fully registeredProducts will conform to FLIR’s publishedproduct specifications and be free from defects in materials andworkmanship during the applicable Warranty Period. PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS
Period
TWO (2) Years
WARRANTY, AT FLIR’S SOLEDISCRETION, IS THE RE­PAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS IN A MANNER, AND BYA SERVICE CENTER, AUTHOR­IZED BY FLIR. IF THIS REMEDY IS ADJUDICATEDTO BE INSUFFICIENT,FLIR SHALL REFUND PURCHAS­ER’S PAID PURCHASEPRICE AND HAVE NO OTHER OBLIGATION OR LIABILITYTO BUYER WHATSOEVER.
5. WARRANTY EXCLUSIONSAND DISCLAIMERS. FLIR MAKES NO OTHER WARRANTY OF ANYKIND WITH RESPECT TO THE PRODUCTS. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MER­CHANTABILITY, FITNESS FOR A PARTICULAR PUR­POSE (EVEN IF PURCHASER HAS NOTIFIEDFLIR OF ITS INTENDED USE FOR THE PRODUCTS),AND NON­INFRINGEMENT ARE EXPRESSLY EXCLUDEDFROM THIS AGREEMENT.
THIS WARRANTY EXPRESSLY EXCLUDES ROUTINE PRODUCT MAINTENANCE, SOFTWARE UPDATES, AND REPLACEMENT OF FUSES,OR DISPOSABLE BATTERIES.FLIR FURTHER EXPRESSLY DISCLAIMS ANY WARRANTYCOVERAGE WHERE THE ALLEGED NONCONFORMITY IS DUE TO NORMALWEAR AND TEAR, OTHER ALTERATION, MODIFICATION, REPAIR, ATTEMPTED REPAIR, IMPROPER USE, IMPROPER MAINTENANCE, NEGLECT, ABUSE, IMPROPER STOR­AGE, FAILURETO FOLLOW ANY PRODUCT INSTRUC­TIONS, DAMAGE (WHETHER CAUSED BY ACCIDENT OR OTHERWISE), OR ANYOTHER IMPROPER CARE OR HANDING OF THE PRODUCTS CAUSED BY ANY­ONE OTHER THAN FLIR OR FLIR’SEXPRESSLY AU­THORIZED DESIGNEE.
THIS DOCUMENT CONTAINS THE ENTIRE WAR­RANTY AGREEMENT BETWEEN PURCHASER AND FLIR AND SUPERSEDES ALL PRIOR WARRANTY NE­GOTIATIONS,AGREEMENTS, PROMISES AND UNDERSTANDINGS BETWEENPURCHASER AND FLIR. THIS WARRANTY MAY NOT BE ALTERED WITH­OUT THE EXPRESS WRITTEN CONSENT OFFLIR.
6. WARRANTY RETURN, REPAIR AND REPLACE­MENT. To be eligible for warrantyrepair or replacement,
Purchaser must notify FLIR within thirty (30) days of dis­covering of any apparent defectin materials or workman­ship. Before Purchaser may returna Product for warranty service or repair, Purchaser must first obtain areturned material authorization (RMA) number from FLIR. To obtain the RMA number Owner must provide an originalproof of purchase. For additional information, to notify FLIRof an apparent defect in materials or workmanship, or to request an RMA number, visit http://www.flir.com. Purchaser is solely responsible for complying with all RMA instructions provided by FLIR including but not limited toadequately packaging the Product for shipment to FLIR andfor all packaging and shipping costs. FLIR will payfor returning
#T559827; r. AC/ 9135/9135; en-US 28
9 FLIR Test and Measurement Limited 2 Year Warranty
to Purchaser any Product that FLIR repairs orreplaces under warranty.
FLIR reserves the right to determine, in itssole discretion, whether a returned Product is covered underWarranty. If FLIR determines that any returned Product isnot covered under Warranty or is otherwise excluded from Warranty coverage, FLIR may chargePurchaser areasonable han­dling fee and return the Product to Purchaser, at Purchas­er’s expense, or offerPurchaser theoption of handling the Product as a non-warranty return.
7. NON-WARRANTY RETURN. Purchaser mayrequest
that FLIR evaluate andserv iceor repair a Product not cov­ered under warranty, which FLIR may agree to do in its sole discretion. Before Purchaser returns a Product for non-warranty evaluation and repair, Purchaser must con­tact FLIR by visiting http://www.flir.com to request an eval­uation and obtain an RMA. Purchaser is solely
responsible for complying with all RMA instructions pro­vided by FLIR including but not limited to adequately packaging the Product for shipment to FLIR andfor all packaging and shipping costs. Upon receipt ofan author­ized non-warranty return, FLIR will evaluate the Product and contact Purchaser regarding the feasibility ofand the costs and fees associated with Purchaser’srequest. Pur­chaser shall be responsible for the reasonable cost of FLIR’s evaluation, for thecost of any repairs or services authorized by Purchaser, and forthe cost of repackaging and returning the Product to Purchaser.
Any non-warranty repair of a Productis warranted for one hundred eighty days (180) days from the date of return shipment by FLIR to be free from defectsin materials and workmanship only,subject to all of the limitations, exclu­sions and disclaimers in this document.
#T559827; r. AC/ 9135/9135; en-US 29
A note on the technical production of this publication
This publication was produced using XML — the eXtensible Markup Language. For more information about XML, please visit http://www.w3.org/XML/
A note on the typeface used in this publication
This publication was typeset using Linotype Helvetica™ World. Helvetica™ was designed by Max Miedinger (1910–1980)
LOEF (List Of Effective Files)
T501026.xml; en-US; AC; 9135; 2013-09-25
#T559827; r. AC/ 9135/9135; en-US 30
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use