TM
USER GUIDE
Second Generation
For Android
FLIR ONE QUICK START
STEP 1
Charge the FLIR ONE with the included USB power cable connected
to a 1A power source. The Charge Indicator LED next to the USB
connection blinks on and o while the FLIR ONE
stays on continuously when it is fully charged. Once the FLIR ONE is
charged, attach it to the phone.
Android Spacer: For users that do not have a case on their Android, a
provided spacer can be attached to the FLIR ONE to create a snug t and nish.
See page 9 for more information.
STEP 2
Download and install the FLIR ONE app, which is available on
Google Play
be displayed to help you get started with the FLIR ONE.
TM
. When you start the FLIR ONE app, a short tutorial will
is charging and
STEP 3
Press the power button on the side of the FLIR ONE to turn it on.
Initially, the indicator light will turn orange, and then it will ash
green when the device is ready.
TM
USER GUIDE 2
STEP 4
Image Info Share Image
Edit Image
Once an image is displayed, tap the color palette icon in the lower
left to change how the image is displayed. Select one of the displayed
color or grayscale palettes.
The camera is in photo mode as indicated just below the image. Tap
the camera icon to capture an image. At the bottom of the display,
select the Mode button (a circle with “Mode”) to bring up a screen
that lets you select another mode (Video, Pano, or Time-Lapse). These
modes are described in a later section of the manual.
The image that displays in the app is a combination of a thermal
image and a daylight image through a unique process called MSX.
The FLIR ONE thermal camera can produce an image even in total
APP OVERVIEW
Control Panel
Spot Meter
Battery
Shutter/
Calibration
darkness. When visible light is available, the FLIR ONE daylight camera
is used to enhance the detail of the FLIR ONE thermal camera.
For close-up scenes, it is possible to optimize the way the daylight
and thermal images are blended. In the Control Panel, you can
enable/disable this mode by clicking on the Close-Up Mode button,
represented by a ower. When Close-Up Mode is enabled, you can
control the image optimization (the alignment of the thermal and
visible image) by adjusting the Optimization slider. Optimizing the
image is described in more detail on page 8.
Refer to the following sections in this guide for additional information
on using the FLIR ONE.
.
More detailed information is also available in the Help & Support feature
within the FLIR ONE app. The FLIR ONE Reference Manual is available
from the FLIR web site: http://www.ir.com/irone
Color Palette Camera Button
Mode Button
PALETTE SCREEN
FLIR Library
WARNING
The FLIR ONE is not waterproof.
Use caution if the FLIR ONE is
used to observe very hot objects
like fire or molten metal.
TM
USER GUIDE 3
FLIR ONE USER GUIDE
The FLIR ONE allows you to see the world in a whole new way, with a
unique blend of thermal and visible imaging. This user guide provides
brief information on how to use the FLIR ONE. Additional information
is available directly from the FLIR ONE app in the Help section of the
Settings Menu.
Charge Indicator LED
Micro USB Power
Thermal Camera
Visible Camera
Phone Connect or Micro USB
Off/On Switch and Power Indicator
CHARGING THE FLIR ONE
Plug the Micro USB end of the power cable into the FLIR ONE and plug
the other end into a 1A power source. The Charge Indicator LED will blink
while the device is charging. The FLIR ONE requires less than one hour
for a full charge (with a 1A source). When the device is fully charged, the
Charge Indicator LED will be on continuously.
TM
USER GUIDE 4
FLIR ONE APP
Image Info Share Image
Edit Image
The latest version of the FLIR ONE app is available on the Google
Play Store. Download and install the app, then start it. If the FLIR
ONE is turned o, the app will prompt you to attach your FLIR ONE
camera and turn it on.
APP OVERVIEW
At the top of the screen there is a black bar with icons for the
Control Panel, Spot Meter, Battery Level, and Calibration. Below that
is the live image, and at the bottom of the screen is another black
bar with icons for the Color Palette, Mode (Photo, Video, Panorama,
or Time-Lapse), Camera, and FLIR Library.
TAKING PICTURES
At the bottom of the screen, select the Mode button and then select
Photo mode. Tap the camera button at the bottom of the screen to
save a snapshot. The images are saved to the FLIR Library. To view
the most recent saved image, tap on the thumbnail in the lower
right. It is not necessary to have the FLIR ONE camera attached to
the phone to view saved images.
APP OVERVIEW
Control Panel
Color Palette Camera Button
MODE SCREEN
Spot Meter
Mode Button
Battery
Shutter/
Calibration
FLIR Library
TAKING VIDEO
At the bottom of the screen, select the Mode button and then select
Video mode. Then tap on the video icon to begin video capture. Tap
on the video icon again to stop the video capture and save the video
in the FLIR Library. To view the captured video, tap the thumbnail
image in the lower right of the screen to access the FLIR Library.
PANORAMA MODE
At the bottom of the screen, select the Mode button and then
select Panorama mode. Tap on the panorama icon to begin the
image capture. The camera will detect if you move left or right, and
will capture images until you move 90 degrees or hit the stop icon.
Panorama mode requires portrait orientation.
PANORAMA MODE
TM
USER GUIDE 5
TIME-LAPSE VIDEO
At the bottom of the screen, select the Mode button and then
select Time-Lapse mode. Then tap on the video icon to display the
Time-Lapse options. Adjust the options as needed, and then tap the
video icon to begin video capture. Tap on the video icon again to
stop the video capture.
FLIR LIBRARY SCREEN
FLIR LIBRARY
A captured image or video may be viewed and edited by selecting
the thumbnail image in the lower right corner of the screen. To view
other images or videos, swipe left or right to access the previous
or next image/video, or tap the Library icon to go to Library view.
Images and videos may be shared through text messaging or
email, and may be edited by changing the color palette, moving the
location of the spot meter or turning the spot meter on/o. While
an image is being viewed, it is possible to swipe up or down to reveal
the visible image that is used for MSX blending.
CHANGING COLOR PALETTES
On the display (the live image), tap the color palette icon in the
lower left to change how the image is displayed. Select one of the
displayed color palettes. The color palettes are described in more
detail in the Help and Support feature of the app (see Settings
Menu). The app allows a choice from nine dierent palettes. Some
include color, grayscale, or a combination of both. To change
the color palette of a saved image, select the Edit Image icon
(represented by a pencil) on the Image View screen.
Edit Image
Image Info Share Image
SPOT METER
When the Spot Meter is enabled (a disabled Spot Meter will have
a slash through the icon), the FLIR ONE will display a temperature
estimate (in degrees C or F) on the image. The accuracy of the Spot
Meter depends on a great many factors, including the distance
from the object, the ambient temperature, and the emissivity of the
material being observed. Users are encouraged to learn more about
the science of Thermography from www.infraredtraining.com. To
switch between Fahrenheit to Celsius, use the Settings option in the
Control Panel, described in the next page.
Note: When the Spot Meter is enabled and the Automatic Calibration is
disabled, the Calibration icon in the upper right will turn red. Tap the icon to
cause the camera to do a manual calibration.
TM
USER GUIDE 6
AUTOMATIC CALIBRATION
The camera has a mechanical shutter inside that periodically activates
and allows the thermal camera to do a calibration or image refresh. When
the shutter activates, the image will freeze for a brief period. The purpose
of the shutter is to allow the camera to provide an improved image. When
the camera rst turns on, and periodically thereafter, the app will perform
an automatic calibration to provide an optimal image. It is also possible
to manually activate the shutter by tapping the Calibration icon in the
upper right on the main screen. Calibration can be switched to manual by
turning o Automatic Calibration in the Settings Menu.
CONTROL PANEL
Select the gear icon in the upper left to open the Control Panel.
The Control Panel allows the user to turn on/o the Light, access the
self-timer settings, enable/disable Close-Up mode, or access the Settings
Menu. Tap the left arrow in the upper left to close the panel.
LIGHT
Multi Spectral Imaging (MSX) is a patented technology which makes
use of the visible camera in the FLIR ONE to maximize detail and image
sharpness. This feature requires some amount of visible light, so in dark
environments turn on the light to enhance the image detail. This feature
makes use of the light that is built into the phone.
CONTROL PANEL
TIMER
The Timer option allows the user to set a time delay before an image is
saved. When the Timer icon is selected, the Timer control panel toggles
between 0s (o), 3s and 10s. The user can set the time delay to 3 or
10 seconds or turn o the time delay option. When the Timer delay is
enabled, the user saves an image by tapping the Camera icon at the
bottom of the screen, and then a countdown timer displays on the image.
CLOSE-UP MODE
FLIR ONE uses two camera sensors (a thermal camera and a visible light
camera) and an exclusive image blending process called MSX to create a
detailed image. By default, the camera should be at least one meter (about
an arm’s length) away from the subject in the image for the blending to
work optimally. For closer subjects, it is possible to adjust the alignment of
the thermal and visible with the slider at the bottom of the image.
TM
USER GUIDE 7
OPTIMIZATION SLIDER CONTROL
When Close-Up mode is enabled, a slider bar appears at the bottom
of the image. For close objects, move the slider to the left to align the
visible image with the thermal image. Observe the right edge of the
coee cup to the right. The image on top shows the lines of the visible
image oset from the thermal image, and the image on bottom shows
the visible image aligned with thermal.
SETTINGS MENU
The Settings Menu allows the user to congure additional features on
the FLIR ONE, as described below.
EMISSIVITY
When the Spot Meter is enabled, the temperature displayed is aected
by many factors, including a property of the target material known
as Emissivity. This property is a relative rating of how well a material
emits or radiates thermal energy. Some materials are more emissive
than others; glossy or reective materials like metals tend to be
poor emitters. For most materials, the default “matte” setting is a fair
approximation.
OPTIMIZATION SLIDER
OFFSET
ALIGNED
TEMPERATURE UNIT
Use this setting to change the temperature unit of measure between
the Fahrenheit and Celsius scale.
SAVE LOCATION
If a GPS signal is available, the location will be added to the captured
images. This makes it possible to see images on a map.
SAVE TO PHOTOS
Turn this on to save a copy of your images and videos in the phone’s
photo gallery. Images will always be stored in the FLIR ONE camera
regardless of this setting. Items already captured will not be copied.
TM
USER GUIDE 8
ANDROID SPACER
Included with your FLIR ONE are two spacer attachments that can be
used to create a snug t and nish for users who do not have a case on
their phone.
To assemble, remove the protective lm revealing the adhesive on the
underside of the spacer. Line up the straight edge of the spacer with
the straight edge of your FLIR ONE. Once lined up properly, apply light
pressure to ensure a complete seal.
Note: Once the spacer is attached, your FLIR ONE will no longer t
inside the supplied bumper.
SPACER OPTIONS
ALL OTHER ANDROID MODELS
SAMSUNG GALAXY S5
There are two dierent spacer options depending on the phone model.
The spacer with the U-shaped divot in the top should only be used
for the Samsung Galaxy s5. All other Android models should use the
spacer with the smooth top.
TM
USER GUIDE 9
HELP
Much more information about the FLIR ONE is described in the Help
feature within the FLIR ONE app. It is also possible to access the
Tutorials from the Help menu.
ABOUT FLIR ONE
The About FLIR ONE menu option provides information about the
FLIR ONE camera, the FLIR ONE app, our company FLIR Systems, Inc.,
and additional legal, licensing and regulatory information.
TM
USER GUIDE 10
TROUBLESHOOTING
FLIR ONE NOT DETECTED
If the FLIR ONE app is not able to detect the FLIR ONE camera,
make sure the phone is properly attached to the FLIR ONE and
fully engaged. Make sure the FLIR ONE is turned on with the power
switch. When the FLIR ONE is turned on, the power indicator should
be ashing green. Make sure the FLIR ONE is adequately charged up
(when the device is plugged into a power source, the charge indicator
on the side of the device near the micro USB connection will stay lit
continuously if the device is fully charged).
TEMPERATURE READINGS NOT ACCURATE
The temperature indicated by the FLIR ONE is always a calculated
estimate and never exact. The indicated temperature is aected by
many factors, especially the emissivity of the object being observed
and the distance to the object. The temperature may be inuenced by
the time of day, by weather conditions, or by other hot or cold objects
in the vicinity that may be reecting o the intended object.
AUTOMATIC CALIBRATION
If Automatic Calibration is disabled, it may be necessary to manually
perform a calibration operation on the FLIR ONE. This allows the
thermal imager to present an optimized image and a more accurate
temperature calculation (see Automatic Calibration on page 7 for more
information).
TM
USER GUIDE 11
LEGAL DISCLAIMER
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to
operate this equipment.
IC Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
VCCI
Product and safety information
Battery and charger information
This device has an internal, non-removable, rechargeable battery. Do not attempt to remove the battery from the device as you may damage
the device. The battery can be charged and discharged hundreds of times, but it will eventually wear out. Use and standby times are
estimates only. Actual times are aected by, for example, device settings, features being used, battery condition, and temperature.
If the battery has not been used for a long time, to begin charging, you may need to connect the charger, then disconnect and reconnect it.
If the battery is completely discharged, it may take several minutes before the charging indicator is displayed. When your charger is not in use,
unplug it from the electrical plug and the device. Do not leave a fully charged battery connected to a charger, as overcharging may shorten
the battery’s lifetime. If left unused, a fully charged battery will lose its charge over time.
Always keep the battery between 15°C and 25°C (59°F and 77°F).
Extreme temperatures reduce the capacity and lifetime of the battery. A device with a hot or cold battery may not work temporarily.
Do not dispose of batteries in a re as they may explode. Dispose of batteries according to local regulations. Recycle when possible. Do not
dispose as household waste.
Use the charger for its intended purpose only. Improper use or use of unapproved chargers may present a risk of re, explosion, or other
hazard, and may invalidate any approval or warranty. If you believe the charger is damaged, take it to a service centre for inspection before
continuing to use it. Never use a damaged charger. Only use the charger indoors.
Take care of your device
Handle your device, charger and accessories with care. The following suggestions help you protect your warranty coverage.
• Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that corrode electronic circuits. If your
device gets wet, allow the device to dry.
• Do not use or store the device in dusty or dirty areas. Moving parts and electronic components can be damaged.
• Do not store the device in cold temperatures. When the device warms to its normal temperature, moisture can form inside the device and
damage electronic circuits.
• Do not attempt to open the device.
• Unauthorized modications may damage the device and violate regulations governing radio devices.
• Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and mechanics. • Use a soft, clean, dry cloth to
clean the surface of the device
Recycle
Always return your used electronic products, batteries, and packaging materials to dedicated collection points. This way you help prevent
uncontrolled waste disposal and promote the recycling of materials. Check how to recycle your FLIR ONE products at www.ir.com/irone/.
The crossed-out wheeled-bin symbol on your product, battery, literature, or packaging reminds you that all electrical and electronic products,
batteries, and accumulators must be taken to separate collection at the end of their working life. This requirement applies in the European
Union. Do not dispose of these products as unsorted municipal waste.
TM
USER GUIDE 12
Loading...