Flipper LC Two Device Universal Instruction Manual

Table of Contents

Use two (2) new AAA batteries. Please see the following instruction when installing the batteries.

Batter y Instal lat ion

1. Open the battery cover in the back of the remote as illustrated.

2. Match the batteries to the + and - marks inside the

case, then insert the batteries. If the installation is correct, the indicator light will flash 2 times.

3. Put the battery cover back on.

4. Press any key, if the indicator light flashes, installation is correct.

Warnings:

1. Do not mix new batteries with old ones or place the batteries incorrectly.

Introduction Functions Set Up Step 1: TV set up Step 2: Set Top Box (STB) Step 3: Favorite Channels Step 4: Dual Mode (TV & STB) Step 5: Lock ON / OFF Options TV Only STB Only Channel Entry Options Other Set-up Options Automatic Code Searching Learning Set Up Troubleshooting Code Retrieval Reset the Remote TV Brand Code List STB Brand Code List

---------------------------------------- 2

-------------------------------------------- 2

----------------------------------------------- 3

--------------------------------- 3

--------------------- 4

--------------- 6

------------------------------------ 7

---------------------------------- 7

----------------------------------------- 7

--------------------------------------- 8

---------------------------- 8

------------------------------ 9

-------------------- 9

------------------------------- 10

---------------------------------- 11

------------------------------------ 11

---------------------------------- 12

------------------------------- 13

---------------------------- 19

Two Device Universal

Instruction Manual

LIP

Functions

ON/OFF: controls both the TV and STB.

Press MUTE once to turn the sound on or off.

Ease of Use

Flipper remote operates both your TV and STB using a minimum number of buttons.

You can program up to 30 of your favorite channels. When activated, the will only advance through these channels. This feature does not change the channel settings of your TV, STB, or other remote controls.

Favorite Channels

Channel Up/Down

Dual Mode

In Dual Mode, the button powers on and off both the TV and STB; and the 0-9 keypad controls the channels on the STB; and controls the TV, eliminating the need to press a button to switch devices.

ON/OFF

Channel Up/Down

Volume Up/Down

Lock

This feature “Locks” the settings of the remote, including favorite channels, and dual mode, and prevents accidental reprogramming.

Thank you for your purchase of the Flipper two device remote control. Flipper is designed for use with your Television and Set Top Box (STB). STB’s are Cable, Satellite, and Digital TV (DTV) receiver boxes.

Flipper is preset to work with most Motorola STBs.

Introduction

2. Please finish the battery installation within 5 ,

otherwise the programmed codes Will be lost. Do not press any key during installation.

3. Remove the batteries if you do not plan to use the

remote for a long period of time to prevent electrolyte leaking. If leaking occurs, clean the contaminated area of the battery compartment and replace the old batteries with new ones.

minutes

Channel Up/Down: Controls the STB

channels.

Volume Up / Down: Controls the TV

volume.

0-9 located under the sliding door, are for set up and channel entry.

TV and STB buttons are used to set up your devices.

ADD and DEL buttons are used to set up favorite channels.

“Dash” is used for DTV channel entry.

LC is for “Last Channel” – returns to the

last channel you are viewing.

Indicator light - flashes during set up and when the remote is used.

Setup

Please follow these step-by-step instructions for the initial set-up. Remember to use new AAA batteries for best results.

If you receive your TV stations through an STB, please note how your TV is connected to the STB. Newer TVs are connected through an AV input option, such as Video 1 or 2, or Antenna 1 or 2. Older TVs may be set to channel 3 or

4. This will allow you to easily reset the TV if you accidentally change your Tv’s channel during set up.

Step 1: TV set up

Locate the 3-digit code for your TV brand in the code list.

1. First, 'prime' the remote. Press and hold ADD until the light

flashes once then turns solid. Then enter 954. The light stays solid then flashes twice.

2 3

the top of the remote will flash once then turn solid. Release the key. Note: If you do not press any key more than 30 seconds,

the remote will exit the program.

3. Enter the first 3-digit code for your TV using the 0-9 key pad. If the code is entered correctly, the light will turn off. If the light stays on, please try again.

4. Try the remote to see if it controls the TV by pressing the key and .

5. If the remote is adjusting your TV, go to Step 2.

6. If the remote does not adjust your TV, repeat the process using the next 3-digit code listed for your TV brand until the remote works. Note: If you are unable to find a working code, see “Other

Set Up Options.”

The code for my TV is ______.

2. Press and hold the TV set-up key. The indicator light at

hi hi

ON/OFF Volume Up/Down

Step 2: Set Top Box (STB)

If you are using a TV without a STB, go to Step 3.

Flipper is preset to Motorola cable STBs. It may not work all Motorola STBs, however. If your STB is manufactured by Motorola, press STB once (the light will flash) and see if Flipper works your STB. If yes, go to Step 3. If not, follow the set up instructions in Step 1: TV, except find your STB code, and press STB instead of TV in # 1.

The code for my STB is ______.

h i

Step 3: Favorite Channels

Setting Favorite Channels is optional. If you do not want a favorite channel list, go to .Step 4

You can program up to 30 of your favorite channels. When set, only scrolls through your Favorite Channels. The 0-9 keypad allows you to key in

any available channel. Programming favorites does not change the settings on your STB or other remote controls.

Channel Up/Down

Note: When advancing through your favorite channels using the buttons, please allow the channel to switch before pressing the button

again.

Make a list of your Favorite Channels. The channels will advance in the order they are entered. For instance, if you program channels 225, 125, 57, and then 563, the

will memorize them in that order and advance as 225, 125, 57, 563. Flipper does NOT place channels in numeric order.

STBs and TVs generally use a three or four digit channel entry system, 000 or 0000. To enter channels, use 0’s as a place holder. For instance, enter channel 7 as 007 (three digit) or 0007 (four digit). For channel 22, enter as 022 or 0022. If your TV or STB requires an Enter key to change channels, please see “Channel Entry Options.”

Please consult your DTV manual. Use the dash “-” button, if needed. Some DTVs do not use a dash, and instead may enter channels in different formats, such as 401 for channel 4-1, or 0301 for channel 30-1. If using a newer TV with an over the air digital turner, you may need to learn the dash key from your existing remote. See “Learning Set Up”

The instructions below assume that you are programming Favorites to work with an STB device. If you are using a TV without a STB, substitute the TV key for the STB key.

1. Press STB then ADD. The indicator light will flash once then turn solid. Release both buttons.

2. Key in the first channel and press the ADD button, key in the next channel and then ADD, and continue until all channels are added. The light will flash one time for each digit.

Channel Up/Down

Make a list:

Channel Format:

DTV channel format:

Adding Favorites:

hi hi

hi I

Note: Flipper can be programmed to turn ON / OFF either the TV or STB only – please see “ON / OFF

Options.”

Step 5: Lock

This feature “Locks” the settings of the remote, including Favorites, and Dual Mode. If you do not want to lock the set up of your remote control, set-up is complete. Enjoy using your Flipper remote!

1. In Dual mode, press and hold ADD. The light will flash once then turn solid. Release the button, and enter 955. The light flashes twice.

2. In TV mode, press and hold TV. The light will flash once then turn solid. Release the button, and enter

95 5.

3. In STB mode, press and hold STB. The light will flash once then turn solid. Release the button, and enter

95 5.

Follow the instructions above, except use code 956 to unlock.

To Lock

To Unlock

In Dual Mode, the turns On and Off both the TV and STB. Occasionally, the remote may only turn On or Off either the STB or TV. If this happens, press the

button again until both devices operate at the same time. To avoid this from happening, place the TV and STB close to each other.

To have control the TV only, control the STB, and control the TV, first set the code for the TV and STB as shown in Step One and Two. Then:

1. Press and hold the STB button and then the button. The indicator light will flash once, then remain flashing. Release both buttons.

ON/OFF

hi hi

TV Only

ON/OFF

Channel Up/Down

Volume Up/Down

ON/OFF Options:

Example: 007 ADD, 044 ADD, 110 ADD, etc., for channels 7, 44, 110; For a DTV: 4 - 1 ADD; 44 - 2 ADD, for channels 4-1, and 44-2

3. Press the STB button after all channels are added to complete the process.

4. Use the buttons to scroll through your Favorites. It may be necessary to scroll through

a second time for all Favorite channels to appear.

5. If you need to add more channels, repeat. Otherwise, go to Step 4.

Follow the instructions above for adding channels, except use the DEL button instead of the ADD button.

To exit favorite channel mode, press and hold DEL and dash - at the same time until the light flashes twice and turns off.

To re-enter, press and hold DEL and dash - at the same time until the light flashes twice and turns off.

Step 4: Dual Mode (TV & STB)

If you are using a TV without a STB, go to Step 5 .

In Dual Mode, the button controls both the TV and STB; and the 0-9 keypad control the STB; and controls the TV

To Dual Mode, press and release ADD. The indicator light will flash once.

To Dual Mode, press and release either TV or STB. The indicator light will flash once.

Note: The remote works best when the TV and STB are close to one another. If the TV and STB do not turn

On and Off at the same time, press the button until both devices turn either On or Off, or manually turn On or Off the device.

hi hi

Channel Up/Down

Deleting Favorites:

Switching Between Favorite and Regular Mode:

Enter

Exit

ON/OFF

Volume Up/Down

ON/OFF

+ 8 hidden pages

Flipper LC Two Device Universal Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual