Flight Deck SC-6502, SC-M500, SC-6501, flightdeck sc6501, flightdeck sc6502 Service Instructions Manual

SI-7AP1E

SERVICE INSTRUCTIONS

Cycle Computer

SC-6502 / SC-6501/ SC-M500

t

Be careful not to pay excessive
attention to the computer data while
riding, otherwise you might have an
accident.

NOTE;

* The all clear (AC) button is used to clear the main unit memory.

* Never disassemble the main unit, as it cannot be reassembled.

* The main unit is fully waterproofed to withstand wet weather

conditions; however, do not deliberately place it into water.

* Avoid leaving the main unit exposed to extremely hot weather

conditions.

* Handle the main unit carefully, and avoid subjecting it to any shocks.

* Do not use thinner or other solvents to clean parts such as the main

unit and sensor, as they may dissolve the part casings.

* To clean these parts, wipe them with a cloth soaked in a weak mixture

of neutral detergent and water.

* If using the SM-6501/M/MD together with an LED lamp from another

manufacturer, the speed measurement function may not work correctly.
If using an LED lamp from another manufacturer, it is recommended
that you use the SM-6500-RS.

Specifications

Meter

Bracket/Sensor unit

SC-6501 / SC-M500SC-6502

SM-6501 SM-6501-MD

STI lever

ST-7700- C

ST-6510

ST-5500-CA

ST-4400

ST-3300/3303

SM-SC70

ST-7800

ST-M510

SL-M510

SM-6501-M

ST-M952 SL-M952

ST-M750 SL-M750

ST-M570 SL-M570

1. Display Modes

“Current speed” and “Gear indicator (bar)” are always displayed

mode 1 mode 2

TIM Trip time

DST Trip distance

ODO ODO meter

STW Stop watch

CLK Clock rpmCadence

VEL

Main display cadence

MAX

Maximum speed

AVEAverage speed

CNTLap counter

Press mode button
once

Press mode button continuously
for 2 seconds or more

Mode Button

SM-6501-MD

WARNING

Mode Button

SM-SC70
SM-6501

SM-6501-M

ST/SP button

Mode button

2. Display Contents

mode 1 mode 2

Current
speed
(VEL)

Clock
(CLK)

Trip time
(TIM)

Trip distance
(DST)

ODO meter
(ODO)

Stop watch–
trip distance
(DST STW)

Stop watch–
average speed
(AVE STW)

Stop watch–
maximum speed
(MAX STW)

Stop watch

Cadence
(rpm)

Main display
cadence

Maximum
speed

Average
speed

No. of gear teeth
(digital)

Gear indicator
(bar)

Pace Arrow

Low battery display

Lap counter

(1)

Current speed (VEL

)

km/h, mph

When main
display cadence
appears on top

Current speed
will appear in
the sub - display

0.0 (2.0) - 130.0km/h

0.0 (1.2) - 80.0mph (Range)
The current speed will appear at
the top of the main display.

(2)

Gear indicator (bar

)

Front display

Rear display

For double : Low position

•••••

For triple : Middle position

••••

For single :

••••••••••••••••••••

Displays;

Top for smallest sprocket
Low for largest sprocket

(3)

Time display (CLK

)

24-hours clock

Gear indicator bar will not appear
if the sensor wire is not connected
or it has been turned off.

Clock will appear when changing
mode 2 to mode 1 and during
power saver function.

7th sprocket for 10-sprocket set ••••••••
7th sprocket for 9-sprocket set •••••••••
7th sprocket for 8-sprocket set •••••••••
7th sprocket for 7-sprocket set •••••••••

3.

Name and function of each part

Front

Rear

STI Brake Bracket

<

ST-7800, ST-7700-C, ST- 6510,
ST-5500-CA, ST-4400, ST- 3300/ 3303

>

<

ST-M510, SL- M510

>

ST/SP button

Mode button

Main Display

1. Current speed
(VEL)

8. Cadence

Sub Display

3-7, 9 -10

2. Gear indicator
(bar)

Switch B

AC All clear
Switch

Battery cap

Switch A

R.H. side lever :
Mode button

L.H. side lever :
ST/SP button

<

ST-M952, ST-M750, ST-M570,
SL-M952, SL-M750, SL-M570

>

ST/SP button

Mode button