Flextest FL2005.1 Instruction Manual

FLEXTEST

Multifunctional Tester

FL2005.1

INSTRUCTION MANUAL

CONTENTS

Title Page

1. SAFETY INFORMATION..................................................1

2. SPECIFICATIONS …........................................................2

3. PARTS & CONTROLS......................................................4

4. BEFORE OPERATION

......................................................7

5.

V VOLTAGE MEASUREMENT........................…........9

6. F

LOOR PROBE RESISTANCE MEASUREMENT...…..…....9

7. HEATING CABLE RESISTANCE <1000Ω

MEASUREMENT

.....………..………………….…………...9

8. MΩ INSULATION RESISTANCE MEASUREMENT......10

9. BATTERY REPLACEMENT..................................…......11

10. MAINTENANCE & CLEANING.....................................11

1. SAFETY INFORMATION

The circuit under test must be de-energized and isolated before

connections are made except for voltage measurement.

Verify operation prior to measuring hazardous voltages (voltage

above 30V AC rms, 42V AC peak and 60V DC).
Do not touch the circuit connections during a test.
Disconnect the live test lead before disconnecting the neutral

test lead.

After insulation tests, to protect from electric shock, capacitive

circuits must to be discharged.

Do not use the meter if the low battery indicator (

BT

) is

displayed.

Test leads (including crocodile clips) must be in good order,

clean and not broken nor cracked.

Do not use the meter if it looks damaged.

Do not use the meter around explosive gas, vapor or dust.
Do not push test button before all connection and preparation is

done. The instrument must only be used by suitably trained and

competent persons.
Do not use the meter with any parts or cover removed.
Do not use the meter in a wet environment.

U.S. PAT. NO. 478,017
JAPAN PAT. NO. 1180870
CHINA PAT. NO. ZL02367250.1

Warnings and Safety symbols:

Caution refer to this manual before using the meter.

Dangerous voltages.

Meter is protected throughout by double insulation or
reinforced insulation.

Comply with IEC1010-1

When servicing, use only specified replacement parts.

2. SPECIFICATIONS

2-1 General Information

Environment conditions :

c Installation Categories III 1000V
d

Pollution Degree 2

e Altitude up to 2000 meters
f Indoor use only

Safety Meets of IEC61010-1 and IEC61557

Display : Dual display, 3-3/4 Digital readout with analog bar

indication.

Sampling Rate : 1 sample/sec.

Manual data Memory and Read : Memory capacity 9 set.
Over Range Indicator : “

” will be displayed.

Low Battery Indication :

The (

BT

) will be displayed when the battery voltage drops

below the operating voltage.

Operating Temperature and Humidity：

0℃ to 50℃ (32℉ to 122℉) below 80% RH (noncondensing).

Temperature Coefficient : 0.10 x (specified accuracy)/ ℃

Storage Temperature and Humidity :

-10℃ to 60℃ (14℉ to 140℉) below 70% RH (noncondensing)

Battery : 6 x 1.5V Size “AA” battery.

Dimensions : 235 (L) x 116 (W) x 54(H) mm ,

(9.3”L x 4.6”W x 2.1”H)

Weight : Approx. 520g (1.15 LB), including battery

Accessories : Test leads, 6pcs batteries, carrying case,

instruction manual, reference card

2

2-2 Electrical Specifications

Accuracies are specified as:

±(...% of reading + ...digits) at 23℃ ±5℃,below 80% RH.

 Insulation Resistance (MΩ)

Range Resolution Accuracy Test Voltages

250V
2MΩ/20MΩ/
200MΩ/ 2GΩ/4GΩ

2MΩ: 1KΩ
20MΩ: 10 KΩ
200MΩ:100 KΩ

2GΩ:1MΩ

10GΩ:10MΩ

250V+30% ~ -0%

500V
4MΩ/40MΩ/
400MΩ/2GΩ/ 4GΩ

4MΩ: 1KΩ

40MΩ: 10KΩ

400MΩ:100 KΩ

2GΩ:1MΩ

10GΩ:10MΩ

500V+30% ~ -0%

1000V
4GΩ

1MΩ

3%+5

(<1000M)

5%+5

(>1000M)

1000V+30% ~ -0%

Analog Bar Graph

0 to 10GΩ

Nominal Current

≧

1mA



H

EATING CABLE

Resistance <1000Ω

Range Resolution Accuracy

Max. open Circuit

Voltage

Overload

Protection

999.9Ω0.1Ω

1%+10

≦

3V

600Vrms



F

LOOR PROBE

Resistance

Range Resolution Accuracy

Max. open

Circuit Voltage

Overload

Protection

99.99KΩ 0.01KΩ

1%+5

≦

3V

600Vrms

3



~V AC Voltage (40Hz～500Hz)

Range Resolution Accuracy Input Impedance

Overload

Protection

999V 1V 2%+3

9MΩ

1000Vrms

Sensitivity : 2V



V DC Voltage

Range Resolution Accuracy Input Impedance

Overload

Protection

999V 1V 2%+3

9MΩ

1000Vrms

Sensitivity : 2V

3. PARTS & CONTROLS

1

2

3

6

4

10

5

7

8

9

4