FlexDSL MiniFlex SHDSL, MiniFlex Single FOM, MiniFlex Dual FOM, MiniFlex FOM User Manual
Ddd
SHDSL.bis
Up to 3
0Mbps
Ethe
rnet
FlexDSL
MiniFlex
Features
• Up to 15Mbps Data Transmission per Copper Pair
• SHDSL and SHDSL.bis, TC-PAM16/32
• Additional TC-PAM4/8/64/128 Available
• Up to 100Mbps Data Transmission per Fiber Line (SFP)
• 1 or 2 Copper Pairs Support
• 1 or 2 Fiber Line Support (SFP)
• 2 Port Ethernet Switch (10/100BaseT)
• QoS, VLAN and RSTP Support
• Point-to-Point and Point-to-Multipoint Operation
• Ring Applications
• Console Port, Telnet, Web, SNMP Management
• 24/48VDC or 110/230VAC Powered, Low Power Consumption
• Included Primary Protection
• Robust DIN-Rail Metal Enclosure
• Smallest Size
• Industrial Temperature Range Available
The FlexDSL Orion3 and MiniFlex SHDSL.bis product family offers a broad range of products, which are based on the latest
SHDSL.bis standards (ITU-T G.991.2 & ETS TS 101524), while also being fully interoperable with all our existing SHDSL
equipment (Orion1, Orion2). The FlexDSL MiniFlex supports beside of the standardized TC-PAM16/32 also the new extended
TC-PAM4/8/64/128 line coding. The support of these extended line codes ensures compatibility with existing SHDSL
equipment, that is already installed, in order to protect customer investments, while at the same time providing an upgrade
path to the newest DSL technologies.
The MiniFlex product family supports beside of SHDSL.bis copper transmisson a dinrail Fiber Converter unit. It has equal
dimensions and supports datarates up to 100Mbps over fiber.
SHDSL.bis allows symmetrical data and voice transmission at speeds up to 15Mbps over a single pair of copper. In addition,
the FlexDSL MiniFlex SHDSL.bis modem range also supports DSL channel bonding for up to 2 copper pairs in order to
achieve speeds to 30.4Mbps!!. An integrated 2 port Ethernet layer 2 managed switch with VLAN, QoS and RSTP support
(10/100BaseT) ensures connectivity to IP services. The FlexDSL MiniFlex SHDSL.bis modems is a perfect solution for a wide
range of applications in which IP services need to be transmitted over copper wires. The MiniFlex product is a small-sized
Orion3 unit with all the functionality included.
Like all FlexDSL Orion products the FlexDSL MiniFlex SHDSL.bis modems are based on industrial components and
manufactured according to highest quality standards providing additional value due to the extended temperature ranges and
higher reliability. The combination of comprehensive functions providing maximum flexibility together with the higher quality of
the FlexDSL MiniFlex SHDSL.bis product family make it the perfect choice for all your DSL needs.
Possible Applications
FlexDSL Telecommunications AG
Steinackerstrassse 31
8902 Urdorf
Switzerland
a)
b)
c)
a) Ethernet Transmission Point-to-Point
b) Ethernet Transmission Point-to-Multipoint
c) Ethernet Add/Drop over a Long Copper Line
Page 1/6
Tel: +41 44 741 52 90
Fax: +41 44 741 52 93
Email: info@flexdsl.ch
Web: www.flexdsl.ch
Device 1
Device 2
Computer
15Mbps Copper Ring
100Mbps Fiber Ring
Quick Installation Guide
Enter a MiniFlex Device
You can use the Monitor (Local Craft Terminal, USB) interface with Hyper Terminal (or any equal program) or you can
address the device with Telnet through the Ethernet interface.
Monitor (LCT, USB) Interface:
• Configure the COM port: Bits per second:9600, Data bits: 8, Parity: None, Stop bits: 1, Flow control: None
• Press <ENTER>.
Telnet through Ethernet Interface:
• Type in command line <Telnet 192.168.0.235> and press <ENTER>. This is the default Ethernet Address for MiniFlex
devices.
After a successful entering the main menu of the device will be displayed.
Configure a MiniFlex Device
A first installation example with the most important commands and points to care about is shown below. We just like to have
an Ethernet transmission between the two devices over 2 SHDSL copper pairs with a speed of 11.4Mbit/s. The pairs should
aggregate (bundle) the data traffic and in case of any SHDSL pair failure, the remaining pairs should continue to work.
Enter in device 1 with the Monitor (LCT, USB) or Telnet interface.
Type following commands Description
3 <↵>
<DEFAULT EVERYTHING> <↵>
<MASTER ON 1> <↵>
<MASTER ON 2> <↵>
<PAYLOAD WAN 1> <↵>
<PAYLOAD WAN 2> <↵>
<NET> <↵>
<SETIP 10.0.2.200> <↵>
<NETMASK 255.0.0.0> <↵>
<GATEWAY 10.0.0.101> <↵>
<M> <↵>
<M> <↵>
2 <↵>
<APPLY ALL> <↵>
<CONFIRM> <↵>
Go to Configuration Management (CM)
Set everything to default configuration
Configure SHDSL 1 as MASTER
Configure SHDSL 2 as MASTER
Configure Ethernet over SHDSL 1
Configure Ethernet over SHDSL 2
Go to NET menu
Set the IP-address of the device
Set the subnet mask
Set the default gateway
Go to Configuration Management (CM)
Go to Main Menu
Go to Fault and maintenance management (FMM)
Apply all configurations (written in the running config.)
Confirm all configurations (written in the startup config.)
FlexDSL Telecommunications AG
Steinackerstrassse 31
8902 Urdorf
Switzerland
Page 2/6
Tel: +41 44 741 52 90
Fax: +41 44 741 52 93
Email: info@flexdsl.ch
Web: www.flexdsl.ch
Loading...