Flexco Novitool Ply 130 Safety And Operation Manual
Novitool® Ply 130™ Separator
Low Volume Step Cutter Blade
Safety and Operation Manual
Separate between the plies of a conveyor belt.
IMPROPER OR UNSAFE use of this tool can result in serious bodily injury! This manual contains important information
about product function and safety. Please read and understand this manual BEFORE operating the tool. Please keep this
manual available for other users and owners before they use the tool. This manual should be stored in a safe place.
www.flexco.com
www.flexco.com
WARNING
Table of Contents
Main Components Ply 130
Main Components Ply 130
Description ..................................................................................................... 5
General Safety Rules ......................................................................................6
Installation of New Faceplate - Retrot Kit Only ....................................10
Installation of Scale - Retrot Kit Only ....................................................12
Installation of Low Volume Step Cutter ...................................................13
Troubleshooting ...........................................................................................18
Ply 130
Maintenance - Measure and Adjust Blade/Roller
™
....................................................................... 3
™
Step Cutter ..................................................3
™
Clearance as Necessary .................................... 19
Parts Lists ......................................................................................................28
Technical Assistance ...................................................................................29
Disclaimer The Ply 130™ ply separator has been tested successfully with different belt
types. However this is no guarantee for good results. Fabricating belts does require the
operator to master skills and have a certain level of craftsmanship. Results also depend
on good practice, material composition and sharpness of blade. If results are not as
expected, please contact Flexco.
ww w.flexco.com
ww w.flexco.com
—2—
Main Components Ply 130
™
6
1
7
8
11
1. Adjuster handle
2. Finger guard
3. Upper traction roller
4. Ply separation blade
5. Lower traction roller
6. Electric motor
7. Adjustable guide
8. Infeed table
9. Operating switch
10. Calibration jig
11. Ply tray
2
3
4
5
9
10
—3—
Main Components Ply 130
Step Cutter
™
5 4 3 2 1 0
13 12 11 10 9 8 7 6 5 4 3 2 1 0
1 2
No. Item No. Description
1 08501 PLY130-STEPCUT
2 08499 PLY130-STEPCUT-RETROFIT
3 08498 PLY130-STEPCUT-GUIDE-EXT
4 08500 PLY130-STEPCUT-TWRENCH
5 08497 PLY130-STEPCUT-BLADES (5)
3 4 5
ww w.flexco.com
ww w.flexco.com
—4—
Description
e Ply 130™ is used to separate between the plies of a
thermoplastic conveyor belt, PVC or polyurethane. is
splitting action is oen required in preparation before
splicing a belt with a splice press.
A great advantage of this ply separator is that it can split
as deep as 5" (130 mm) in one pass.
e robust construction of the Ply 130™ allows for
precise separating of thermoplastic belts – both thin
and thick between plies as little as 0.014" (0.35 mm)
can be separated.
Tool Specifications
Ply 130™ Tool Specifications
Specifications
Splitting Depth 1.5" (40 mm) 5.1" (130 mm)
Belt thickness above cut .014" (0.35 mm) .3" (8 mm)
Belt thickness below cut .014" (0.35 mm) .2" (5 mm)
Maximum belt thickness N/A .4" (10 mm)
Tool dimensions
Tool weight 125 lbs (57kgs)
Minimum Maximum
22" x 19" x 14"
(560 x 480 x 360 mm)
e Ply 130™ can be used to prepare nger over nger
splices and stepped splices. With the adjuster handle you
determine the depth to split the belt. It may be possible
to split between every ply of the belt and in this way to
generate two or three separations within one belt.
e low volume step cutter blade separates stepped edges.
e layer passing above the separation blade is cut o
simultaneously
Ply 130™ Ordering Information
Item
Code
Ply 130™
08800 PLY130-230V+N1PH50HZ-SCHUKO
08801 PLY130-400V+NV3PH50HZ-IEC60309
08802 PLY130-115V1PH60HZ-NEMA-5-15 cETL
08803 PLY130-230V1PH60HZ-NEMA-L6-20 cETL
08804 PLY130-230V1PH60HZ-NEMA-L6-30 cETL
08805 PLY130-230V1PH60HZ-NEMA-L6-15 cETL
Ordering
Number
Mark Plug
08806 PLY130-230V1PH60HZ-NEMA-6-15 cETL
08807 PLY130-230V1PH60HZ-NEMA-6-20 cETL
08808 PLY130-230V1PH60HZ-NEMA-6-30 cETL
08809 PLY130-230V3PH60HZ-NEMA-L15-20 cETL
08810 PLY130-230V3PH60HZ-NEMA-L15-30 cETL
08811 PLY130-460V3PH60HZ-NEMA-L16-20 cETL
08812 PLY130-460V3PH60HZ-NEMA-L16-30 cETL
08832 PLY130-230V1PH50HZ-IEC60309-16
08833 PLY130-230V1PH50HZ+N-BS1363-13
08834 PLY130-230V3PH60HZ-NEMA-18-20
Cart
08100 PLY130-CART N/A
Replacement Blades
08014 PLY-BL-BLADE-&-JIG-KIT N/A
08490 PLY130-BLADE N/A
—5—
Ply 130™ ply separator
General Safety Rules–Save These Instructions–
Signal words:
“DANGER” indicates an imminently hazardous
situation which, if not avoided, will result in
death or serious injury. e signal word is
limited to the most extreme situations.
“WARNING” indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
“CAUTION” indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury. It may also be used to
alert against unsafe practices.
Safety Symbol
!
is international safety symbol is used to
identify and call attention to specic
safety matters.
Safety Information
!
CAUTION
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause
you to lose control.
!
WARNING
Never leave tool until it comes to a complete stop.
!
WARNING
Store idle tools out of reach of children and other
untrained persons. Tools are dangerous in the
hands of untrained users.
2. ELECTRICAL SAFETY
!
DANGER
e Ply Separator is a single insulated tool and
needs a multiple wire grounded power cord and
grounded power supply system. e machine
is provided with an electrical plug to ensure
connection to the proper supply power.
To Avoid Severe Personal Injury or Property
Damage, read carefully and understand the
following Safety Precautions.
1. WORK AREA
!
CAUTION
Keep your work area clean and well lit.
Cluttered benches and dark areas invite accidents.
!
DANGER
Do not operate power tools in explosive
atmospheres, such as in the presence of ammable
liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
!
WARNING
Avoid body contact with grounded surfaces such
as pipes, radiators, ranges, and refrigerators.
ere is an increased risk of electric shock.
!
WARNING
Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock and will damage
the tool.
www.flexco.comwww.flexco.com
—6—
Ply 130™ ply separatorGeneral Safety Rules –Save These Instructions–
!
DANGER
Do not abuse the cord. Never use the cord to carry the
tool or pull the plug from a receptacle. Keep cord away
from heat, oil, sharp edges, or moving parts. Replace
damaged cords immediately. Damaged cords increase
the risk of electric shock.
!
WARNING
Do not use outdoors. is power tool is designed
for indoor use only.
!
WARNING
Do not use tool if switch does not turn it on or
o. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
Disconnect machine from supply circuit before
servicing. Ensure all protective ground connections are in place aer service. Replace fuses only
with those of the same current rating, interrupt
rating, voltage rating and construction.
3. PERSONAL SAFETY
!
WARNING
Do not overreach. Keep proper footing and
balance at all times. Proper footing and balance
enables better control of the tool in unexpected
situations.
!
CAUTION
Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat,
or hearing protection must be used for appropriate conditions.
!
WARNING
Never alter or remove safety devices.
!
WARNING
Keep your hands and ngers away from all moving and sharp parts, e.g. rolls and blade, at
all times.
!
WARNING
Engage caster locks on cart when not transporting
!
WARNING
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use tool while tired or under the inuence of
drugs, alcohol, or medication. A moment of inattention while operating power tools may result in
serious personal injury.
!
WARNING
Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose
clothes, jewelry, or long hair can be caught in
moving parts.
!
WARNING
Avoid accidental starting. Be sure switch is o
before plugging in. Carrying tools with your
nger on the switch or plugging in tools that have
the switch on invites accidents.
!
WARNING
Machine is heavy. Use liing aids.
4 TOOL USE AND CARE
!
WARNING
Always use the ply separator on a level, rm surface. Splitting should be performed operating the
machine with two hands on the material.
!
CAUTION
Do not force tool when the belt material blocks
or jams and do not continue feeding the material
through tool. When jamed put the operating
direction in reverse to remove the material.
!
WARNING
Do not use tool if switch does not turn it on or
o. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
—7—
Ply 130™ ply separator
General Safety Rules –Save These Instructions–
!
WARNING
Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing or transporting the tool. Such preventive
safety measures reduce the risk of starting the tool
accidentally.
!
WARNING
Store idle tools out of reach of children and other
untrained persons. Tools are dangerous in the
hands of untrained users.
!
CAUTION
e Ply Separator should not be used to split other materials than thermoplastic belting materials.
e thickness of the belting material should never
exceed 10 mm.
!
CAUTION
Check for misalignment or binding of moving
parts, breakage of parts, and any other condition
that may aect the tool’s operation. If damaged,
have the tool serviced before using. Many
accidents are caused by poorly maintained tools.
!
WARNING
Stow foot switch when not in use.
!
CAUTION
When servicing a tool, use only identical replacement parts. Use of unauthorized parts or failure
to follow Maintenance Instruction may create a
risk of electric shock or injury.
!
DANGER
Do not use power tools if the housing is damaged
or not closed. Damaged or (partially) open housing can lead to electric shock. Such tools should
not be used until repaired or closed.
!
CAUTION
Do not wipe plastic parts with solvent.
Solvents such as gasoline, thinner, benzene, carbon tetrachloride, and alcohol may damage and
crack plastic parts. Do not wipe them with such
solvents. Wipe plastic parts with a so cloth lightly dampened with soapy water and dry throughly.
!
WARNING
NEVER use a tool which is defective or operating
abnormally. If the tool appears to be operating
unusually, making strange noises, or otherwise
appears defective, stop using it immediately,
disconnect from power supply and arrange for
repairs.
!
WARNING
Disconnect and stow cables before moving.
5. SERVICE AND MAINTENANCE
!
WARNING
Tool service must be performed only by qualied
repair personnel. Service or maintenance performed by unqualied personnel could result in a
risk of injury.
!
WARNING
Disconnect electrical plug from the power supply
before opening/servicing the machine.
www.flexco.comwww.flexco.com
—8—
!
CAUTION
Maintain tools with care. Keep blades sharp and
clean. Properly serviced tools and knifes with
sharp edges are less likely to bind or create debris
and are easier to control.
6. PLY CUTTER SAFETY
!
WARNING
Make sure that the power cable is not near the
material entrance opening.
!
WARNING
Keep your body positioned perpendicular to the
material feeding direction on the opposite side of
the electric motor.
Ply 130™ ply separatorGeneral Safety Rules –Save These Instructions–
!
WARNING
Keep your hands away from the feeding rolls and
splitting area. Always guide the material in a way
that your hands have a minimum distance of 3.94”
(10 cm) from this area.
!
CAUTION
Do not use dull or damaged blades/ knives.
7. PLY CART SAFETY
!
WARNING
Avoid inclines, declines and oor obstructions
when pushing cart. Only push cart in directions
permitted by xed casters, never pull or attempt
to slide sideways.
8. REPLACING THE BLADE
!
WARNING
!
WARNING
Always wear cut-proof safety gloves and safety
glasses when replacing blade. Blade is razor sharp,
treat it accordingly.
!
WARNING
Before performing a blade replacement, follow all
procedures stated in manual.
!
WARNING
Only authorized and trained technicians should
work on the ply separator.
!
WARNING
Test the splitter aer blade / knife replacements to
make sure that it can be used safely.
!
WARNING
Stow spare blades safely.
Disconnect power.
!
CAUTION
Do not attempt to resharpen blades. is will
aect splitting completely through belt.
—9—
A
Installation of New Faceplate - Retrofit Kit Only
Prior to installing the Low Volume Step Cutter, the upper faceplate may need to be replaced. e
step cut retrot kit (08499) is required on Ply 130 separators prior to those with serial number
C1-122352-13W.
Caution! Disconnect Ply 130
B1A1
plug from the power source.
Remove the two 5 mm hex
screws from existing top
faceplate on Ply 130.
B1A2
Lightly tap at back edge of top
faceplate with a rubber mallet
until a small opening appears
in between the top cover plate
and the Ply 130 body. A small
rubber tipped chisel may be
required if the faceplate is a
tight t.
While tapping back edge of
faceplate alternate low pulling
force on each side of faceplate
until removed. Discard
faceplate.
www.flexco.comwww.flexco.com
—10—
Loading...