flexbar Z10, Z8, Z6 User Manual
Z10
SERIES
Z10 • Z8 • Z6
ZO
OM STEREO MICROSCOPES
MANUAL
250 Gibbs Road, Islandia, NY 11749 • 631-582-8440 (P) • 631-582-8487 (F)
www.flexbar.com • sales@flexbar.com
Z10
ONTENTS
C
SERIES STEREO MICROSCOPES
SAFETY NOTES .................................................................................................................. 3
CARE AND MAINTENANCE ................................................................................................ 3
INTRODUCTION .................................................................................................................. 4
UNPACKING AND COMPONENTS ..................................................................................... 4
COMPONENT DIAGRAMS ............................................................................................... 5-7
ASSEMBLY .......................................................................................................................... 8
ADJUSTMENT AND OPERATION
ADJUSTING BINOCULAR VIEWING HEAD ................................................................. 12
FOCUS ADJUSTMENT ................................................................................................. 13
INSTALLING THE BEAM SPLITTER ............................................................................ 14
ASSEMBLING THE BEAM SPLITTER, VIEWING HEAD & CAMERAS ....................... 14
INSTALLING THE IRIS DIAPHRAGM ........................................................................... 15
OPERATING THE IRIS DIAPHRAGM .......................................................................... 15
SPECIFICATIONS .............................................................................................................. 16
TROUBLESHOOTING ........................................................................................................ 17
MAINTENANCE.................................................................................................................. 18
SERVICE ............................................................................................................................ 18
WARRANTY ....................................................................................................................... 18
250 Gibbs Road, Islandia, NY 11749 • 631-582-8440 • www.flexbar.com 2
Z10 SERIES STEREO MICROSCOPES
SAFETY NOTES
1. Open the shipping carton carefully to prevent any accessory, i.e. objectives or eyepieces, from
dropping and being damaged.
2. Keep the instrument out of direct sunlight, high temperature or humidity, and dusty environments.
3. If any specimen solutions or other liquids splash onto the stage, objective or any other component,
disconnect the power cord immediately and wipe up the spillage. Otherwise, the instrument may be
damaged.
4. LAMP REPLACEMENT -- CAUTION: the glass envelope of the lamp may be extremely
hot. DO NOT attempt to change the lamp before it is completely cooled or without
wearing adequate skin protection.
5. All electrical connectors (power cord) should be inserted into an electrical surge protector to prevent
damage due to voltage fluctuations.
6. FUSE REPLACEMENT -- For safety when replacing the fuse (ONLY replace with the
7. Confirm that the input voltage indicated on your microscope corresponds to your line voltage. The
use of a different input voltage other than indicated will cause severe damage to the microscope.
NOTE: Always plug the stereomicroscope power cord into a suitable grounded electrical outlet. A
grounded 3-wire cord is provided.
same size, type and rating of original fuse), be sure the main switch is in the off position,
disconnect the power cord from outlet, and replace the fuse. Reconnect the power cord
and turn unit on.
CARE AND MAINTENANCE
1. Do not attempt to disassemble any component including eyepieces, objectives or focusing assembly.
2. Keep the instrument clean; remove dirt and debris regularly. Accumulated dirt on metal surfaces
should be cleaned with a damp cloth. More persistent dirt should be removed using a mild soap
solution. Do not use organic solvents for cleansing.
3. The outer surface of the optics should be inspected and cleaned periodically using an air stream from
an air bulb. If dirt remains on the optical surface, use a soft, lint free cloth or cotton swab dampened
with a lens cleaning solution (available at camera stores). All optical lenses should be swabbed using
a circular motion. A small amount of absorbent cotton wound on the end of a tapered stick makes a
useful tool for cleaning recessed optical surfaces. Avoid using an excessive amount of solvents as
this may cause problems with optical coatings or cemented optics or the flowing solvent may pick up
grease making cleaning more difficult.
4. Store the instrument in a cool, dry environment. Cover the microscope with the dust cover when not
in use.
5. Flexbar
proper performance and to compensate for normal wear. A regular schedule of preventative
maintenance by qualified personnel is highly recommended. Your authorized Flexbar
®
microscopes are precision instruments which require periodic servicing to maintain
distributor
can arrange for this service.
250 Gibbs Road, Islandia, NY 11749 • 631-582-8440 • www.flexbar.com 3
Z10
SERIES STEREO MICROSCOPES
INTRODUCTION
ongratulations on the purchase of your new Flexbar® microscope. Flexbar microscopes are
C
engineered and manufactured to the highest quality standards. Your microscope will last a lifetime if
used and maintained properly. Flexbar
by our staff of trained technicians in our New York facility. Careful quality control procedures ensure each
microscope is of the highest quality prior to shipment.
®
microscopes are carefully assembled, inspected and tested
UNPACKING AND COMPONENTS
Your microscope arrived packed in a molded shipping carton. Do not discard the carton
carton should be retained for reshipment of your microscope if needed. Avoid placing the microscope in
dusty surroundings or in high temperature or humid areas as mold and mildew can form. Carefully
remove the microscope from the shipping carton and place the microscope on a flat, vibration-free
surface.
: the shipping
COMPONENTS DIAGRAM
250 Gibbs Road, Islandia, NY 11749 • 631-582-8440 • www.flexbar.com 4
Z10
Binocular Head
SERIES STEREO MICROSCOPES
Diopter Adjustment Rings
Eyepieces
Eyepiece Tubes
Locking Screw for
Viewing Head
Coarse Focus Knob
Fine Focus Knob
Reflected Illumination
Adjustment Knob
LED Stand
Zoom Knob
Locking Screw for
Optical Body
Optical Body
Objective Lens
Transmitted Illumination Adjustment Knob
Stage Clips
250 Gibbs Road, Islandia, NY 11749 • 631-582-8440 • www.flexbar.com 5
Z1
0 SERIES STEREO MICROSCOPES
Ball Bearing
m Stand
Boo
Tilting Ergo Binocular
Vi
wing Head
e
250 Gibbs
Bonder Arm
Road, Islandia, NY 11749 • 631-582-8440 • www.flexbar.com 6
Loading...