Flex-a-Lite 365 User Manual

Page 1

Scirocco Radiator

“Grin Scirocco Radiator ” Installation:

1. Assemble the Flex-a-lite model 365 Scirocco fan according to the instructions, then follow these directions for adding the additional set of holes in the mounting brackets.

2. Center the fan assembly between the two upper fan mounts on the radiator side tanks and fasten using the bolts provided.

3. Mark lower mounting hole locations on the fan assembly mounting anges so they line up with the lower set of fan mounts on the radiator tanks.

4. Remove fan assembly from radiator.

5. Use le or drill to elongate the holes to t the Grin radiator holes.

6. Fasten fan assembly to radiator using the bolts, lock washers and at washers provided.

Assembly & Mounting Instructions

1. Fan blades are factory mounted as pullers. To use as a pusher simply slide E-clips o the ends of the motor shafts, reverse blades and slide E-clips back into position on the ends of the motor shafts.

2. For puller mode attach the black wires to a positive 12 volt power source and the red wires to ground. For pusher mode attach the black wires to ground and the red wires to a positive 12 volt power source.

3. Mount the Flex-a-lite fan/shroud assembly to the radiator using the spacers*, bolts, at washers and lock washers provided (Diagram A). Always check to make sure there is sucient clearance for the bolt threading into the radiator mounting bosses so that it does not bottom out and crack the radiator. If sucient clearance does not exist, use a shorter bolt or a spacer under the head of the bolt.

*Spacers are used between the bracket and mounting bosses on radiators where the mounting bosses on one side of the radiator are shorter than the other. The spacers allow the shroud to lay at on the radiator cor

for even support and a good seal.

Scirocco O.E. Fan Replacement Instructions

1. Disconnect the battery ground cable.

2. Disconnect the fan motor wiring connector.

3. Remove the (4) shroud retaining bolts.

4. Remove the shroud and fan assembly from the car.

5. Install Flex-a-lite fan/shroud assembly as described above.

6. Fans can be wired by splicing into existing fan wiring harness. For increased control of fan, purchase Flex-a-lite illuminated Switch #31148 or Adjustable Temperature Sensor #31147.

“Grin Scirocco Radiator ” Installation:

1. Assemble the Flex-a-lite model 365 Scirocco fan according to the instructions, then follow these directions for adding the additional set of holes in the mounting brackets.

2. Center the fan assembly between the two upper fan mounts on the radiator side tanks and fasten using the bolts provided.

3. Mark lower mounting hole locations on the fan assembly mounting anges so they line up with the lower set of fan mounts on the radiator tanks.

4. Remove fan assembly from radiator.

5. Use le or drill to elongate the holes to t the Grin radiator holes.

6. Fasten fan assembly to radiator using the bolts, lock washers and at washers provided.

Dual Electric Fan #365

Assembly & Mounting

Instructions:

Fan blades are factory mounted as pullers. To use as a pusher simply slide E-clips off the ends 1. of the motor shafts, reverse blades and slide E-clips back into position on the ends of the motor shafts.

For puller mode attache the black wire to a positive 12 volt power source and the red wires to 2. ground. For pusher mode attach the black wires to ground and the red wires to a positive 12 volt power source.

Mount the Flex-a-lite fan/shroud assembly to the radiator using the spacers*, bolts, washers and 3.

lock washer provided (Diagram A). Always check to make sure there is sufcient clearance for

the bolt threading into the radiator mounting b bosses so that it does not bottom out and crack the

radiator. If sufcient clearance does not exist use a shorter bolt or a spacer under the head of the

bolt.

*Spacers are used between the bracket and mounting bosses on radiators where the mounting

bosses on one side of the radiator are shorter than the other. The spacers allow the shroud to lay at

on the radiator core for even support and a good seal.

Scirocco O.E. Fan Replacement

Disconnect the battery ground cable.1.

Disconnect the fan motor wiring connector.2.

Remove the (4) shroud retaining bolts.3.

Remove the shroud and fan assembly from 4. the car.

Install Flex-a-lite fan/shroud assembled as 5. described above.

Fans can be wires by slicing into existing fan 6. wiring harness. For increased control of fan purchase Flex-a-lite illuminated Switch #31148 or Adjustable Temperature Sensor #31147.

Instructions:

DIAGRAM A

Allen Cap Bolt

Lock Washer

Flat Washer

Spacer (if needed)

“Grifn Scirocco Radiator ”

Installation:

Center the fan assembly between the two upper fan mounts on the radiator side tanks and fasten 1. using the bolts provided.

Mark lower mounting hole locations on the fan assembly mounting anges so they line up with the 2. lower set of fan mounts on the radiator tanks.

Remove fan assembly from radiator.3.

Use le or drill to elongate the holes to t the Grifn radiator holes.4.

Fasten fan assembly to radiator using the bolts, lock washers, and at washers provided.5.

The Flex-a-lite Limited Warranty

Flex-a-lite Consolidated, 7009-45th St. Ct. E. Fife, WA 98424, Telephone No. 253-922-2700, warrants to the original purchasing user, that all Flex-a-lite products to be free of defects in material and workmanship for a period of 365 days (1 year) from date of purchase. Flex-a-lite products failing within 365 days (1 year) from date of purchase may be returned to the factory through the point of purchase, transportation charges prepaid. If, on inspection, cause of failure is determined to be defective material or workmanship and not by misuse, accidental or improper installation, Flex-a-lite will replace the product free of charge, transportation prepaid. Flex-a-lite will not be liable for incidental, progressive or consequential damages. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you speciﬁc legal rights and you may have other rights, which vary from state to state. The Flex-a-lite warranty is in compliance with the Magnuson-Moss Warranty Act of 1975.

Rev. 11-08-12 #99966 Page 1 of 1