Installing an eZeBox Starter Unit
Supplied Parts
Fixing to solid surface
2x
eZeBox Starter Unit
(4 way shown)
Accessories pack
contained under lid
x1 x4 x2 x1 x2
Current & Voltage rating : 16A, 230V AC
Knock-outs : 20mm (x4) & 25mm (x1)
Table 1: bracket spacing guide
x1
• At the appropriate spacings (see
Table 1) secure each bracket to
the surface with a single screw
(not supplied).
• Prior to snapping-in the eZeBox
unit, remove appropriate knockouts for cable/conduit entry.
• Clip the eZeBox unit securely into
the fixing brackets.
Fixing to cable tray / wire basket
2x
• At the appropriate spacings (see
Table 1) secure each bracket
using tie wraps.
• Prior to snapping-in the eZeBox
unit, remove appropriate knockouts for cable/conduit entry.
• Clip the eZeBox unit securely into
the fixing brackets.
Fixing to trunking
2x
2x
2x
Bracket
removal
Outlets
2 way
4 way
6 way
8 way
10 way
12 way
Spacing /mm
± 5
45
± 10
90
± 10
140
± 10
190
± 10
240
± 10
290
Optional Extras
If the end socket is reserved the eZeBox Starter Unit
can be expanded at any time. By connecting an:
• eZeBox Expansion Unit
allows for the unit to be extended
using the existing controls.
• eZeBox Tap-off Unit
allows for an additional
separately controlled
circuit.
• eZeBox Adaptor Unit
For 2 circuit control packs
In-line units can be plugged in directly
‘unit to unit’ or via a suitable lead.
AA
• At the appropriate spacings (see
Table 1) secure each bracket
using fixings supplied.
• Prior to snapping-in the eZeBox
unit, remove appropriate knockouts for the cable/conduit entry.
• Clip the eZeBox unit securely into
the fixing brackets.
Fixing to drop rods
2x
AA
• Ensure drop rods are pitched at
the appropriate spacings (see
Table 1) and secure each bracket
to a drop rod using two tie wraps
for each drop rod.
• Prior to snapping-in the eZeBox
unit, remove the appropriate
knock-outs for cable/conduit entry.
• Clip the eZeBox unit securely into
the fixing brackets.
Fixing to conduit box
1x
• Remove knock-out on base of
wiring box for cable entry.
• Locate and secure the eZeBox
unit onto the conduit box, break
through the appropriate holes for
the screw, (not supplied).
• Anchor other end of the eZeBox
unit, by bending and fixing the
support bracket.
4x
1x
Sw/L
D2/0V
Earth
Em/L
Neutral
Aux/L
D1/10V
12
R1
Dim
Aux/L
Sw/L
D2/0V
Earth
Em/L
Neutral
D1/10V
Leaflet number: 22/039/01_19/12/2011
1
2
4
3
6
5
E
1
2
4
3
6
5
E
1 2
E
E
Link in position 2
party
Third
emergency test is remote.
Live
Where there is no emergency circuit or the
Neutral
Em/L
Neutral
Aux/L
1
2
3
Em.1
control
*
Earth
Sw/L
Earth
4
E
Applicable if third party
control has dimming output
D2/0V
D1/10V
R1
Dim
6
5
12
Live
Neutral
Earth
Sw/L
Earth
Em/L
Neutral
Aux/L
1
2
4
3
E
Applicable if flex7 control
D2/0V
D1/10V
6
5
1 2
E
party
Third
control
*
Link in position 2
E
Em.1
Warning: 230V AC
Flex Connectors Limited, Unit 8 The Gate Centre,
Syon Gate Way, Brentford, Middlesex TW8 9DD, UK
Telephone: +44 (0) 20 8580 1066
Fax: +44 (0) 20 8580 1062
Website: www.flexconnectors.co.uk
Email: info@flexconnectors.co.uk
device is dimming type
This product should be installed and maintained in accordance with:
BS 7671:2008 Requirements for Electrical Installations (IEE Wiring
Regulations 17th Edition.)
Sw/L
D2/0V
Earth
Em/L
Neutral
R2
R1
Dim
12
Aux/L
1
2
3
1 2
Link in position 2
D1/10V
4
6
5
E
*
E
Live
Neutral
Earth
With local emergency test where non-emergency
fittings will switch OFF during an emergency test.
Sw/L
Earth
Em/L
Neutral
Aux/L
Wiring Options for the eZeBox Starter Units
1
2
4
3
E
Applicable if third party
control has dimming output
D2/0V
D1/10V
R1
Dim
6
5
1 2
E
Em.1
party
Third
control
*
Live
Neutral
Earth
With local emergency test where non-emergency
fittings can remain ON during an emergency test.
Applicable if third party
control has dimming output
Live
Neutral
Earth
Sw/L
Earth
Em/L
Neutral
12
Aux/L
1
2
4
3
E
Applicable if flex7 control
device is dimming type
D2/0V
D1/10V
R2
R1
Dim
6
5
12
Live
Neutral
Earth
Sw/L
Earth
Em/L
Neutral
Aux/L
1
2
4
3
E
Applicable if flex7 control
device is dimming type
D2/0V
D1/10V
6
5
1 2
E
Link in position 1
Em.1
Live
Neutral
Earth
Applicable if flex7 control
device is dimming type
Link in position 1
Live
E
Neutral
Earth
Applicable if flex7 control
device is dimming type
diagram
eZeBox wiring
Hard-Wired
device.
lighting control
with third party
control device.
plug-in lighting
Using a flex 7
Compatible Controllers:
Dimming
fnc3000 fns3000
fnc3000/-- fns3400
fnc4000 fns3400/--
fnc4000/--
Non-dimming
fnc1000 fns1000
fnc1000/-- fns1200
fnc2000 fns1400
fnc2000/-- fns1200/--
Using a flex 7
fnv100 fns1400/--
integrated
plug-in lighting
emergency test.
control device with
Compatible Controllers:
Dimming
fnc4000/E
fnc4000/--/E
Non-dimming
fnc2000/E
fnc2000/--/E
eZeBox connection units have been designed and extensively tested for use with the flex 7 control range of sensors. Flex Connectors cannot guarantee compatibility with third party sensor products and cannot be held responsible for any deviance from expected
performance that may arise as a result. Flex Connectors are happy to provide support where possible to ensure compatibility and compliance with British Standards. Caution: Wiring shown for third party control is indicative only. Refer to third party information.
Loading...