Flex Pourable Sealert User Manual

Product Data Sheet

FLEX POURABLE SEALER

DESCRIPTION

Flex Pourable Sealer is a high-performance, single component, polyurethane-base, self-leveling pitch pan
sealant. Flex Pourable Sealer is self-priming and requires no mixing; it is simply poured in place and
cures to form a resilient, tough seal. Flex Pourable Sealer produces a flexible, long-lasting seal with
extraordinary adhesion, cohesion, elasticity and abrasion resistance.

THIS PRODUCT IS FORMULATED TO PROVIDE:

· Single component sealant which requires no mixing.

· Functions from - 40° F to 180° F.

· Bonds to most substrates without a primer.

· Resists penetration and puncturing by sharp objects.

· Resists permanent deformation from compression.

· Resists deterioration from weather, stress, movement, water, and aging without

SUGGESTED USES

Flex Pourable Sealer is used to seal objects that are difficult to flash requiring a pitch pan installation.

TYPICAL PHYSICAL PROPERTIES

distortion or failure.

Property Test Method Result

Service temperature range -40° F to 180° F
Expected life Up to 20 years
Shrinkage None
Movement capability ASTM C 719 ±25%
Tensile strength ASTM D 412 350 psi
Ultimate elongation at break ASTM D 412 800%
Lower temperature flexibility ASTM C 746 -40° F
Hardness at standard ASTM C 661 25 ±2
Conditions/Shore A
Accelerated weathering Atlas 6500 – watt xenon arc Excellent

VOC Content: 75.2 g/L or 0.63 lbs. of V.O.S. per gallon of material.

INSTALLATION

Surface Preparation Pitch pans or joints must be clean, dry, and free of any foreign materials for

optimum performance. Pitch pan surfaces must be structurally sound and free of all loose aggregate,
paint, oil, grease, asphalt, wax, mastic compounds, waterproofing compounds, or form release materials.

(Produced by Sonneborn)

_____________________________________________________________________________________________________

Flex Membrane International Corp. 2670 Leiscz’s Bridge Road, Suite 400, Leesport, PA 19533

Tel: [phone] Fax: [phone] www.FlexRoofingSystems.com

Page

1

NOTE: Do not install when rain is expected before the sealant reaches initial cure. Substrates must be
absolutely dry or bubbling may result. **All Flex Roof Systems require pitch pans to be made of
Flexclad coated metal.

METHOD OF APPLICATION

1) Install Flexclad Pitch Pan around the penetrating object according to Flex’s current specifications and
details.

2) Fill bottom of pitch pans with concrete or other suitable fillers. Do not use other caulks or sand as a
bottom bed in a pitch pan. Flow the sealant into the pitch pan and taper the sealant outward to provide
positive drainage. The maximum depth should be 3/8” deep.

CURING TIMES

Cure of Flex Pourable Sealer will vary with temperature and humidity. Under normal conditions (75° F
and 50 % humidity), Flex Pourable Sealer will have a skin overnight or within 24 hours and will fully
cure in approximately one week.

CLEAN UP

Immediately after use and before sealant has cured, clean equipment or material with an approved,
suitable cleaner or solvent.

FOR BEST PERFORMANCE

● Protect unopened containers from heat and direct sunshine.

● In cool or cold weather, store containers at room temperature for at least 24 hours

before using.

● Do not apply over freshly treated wood; treated wood must have weathered for at least

6 months.

● Do not apply below freezing temperatures unless substrates are completely dry, free of
moisture, and clean.

● Polyurethane sealants should not come in contact with oil-base caulking, silicone,

sealants, polysulfides, fillers impregnated with oil, asphalt, or tar.

COMPLIANCES

Federal Specification TT-S-00230C, Type I, Class A
ASTM C 920, Type S, Grade P, Class 25
Corps. of Engineers CRD-C-544-91

WARNING

This product contains polyol, fumed silica, mineral spirits, talc, quick lime, and titanium dioxide which could be
harmful if mishandled. Contact with skin and eyes should be avoided and necessary protective equipment and
clothing should be worn. This is a combustible liquid.

Flex Membrane International Corp, maintains Material Safety Data Sheets (MSDS) on all of its products. Material
Safety Data Sheets contain health and safety information for your development of appropriate product handling
procedures to protect your employees and customers. Flex Material Safety Data Sheets should be read and
understood by all of your supervisory personnel and employees before using Flex products in your facilities.

_____________________________________________________________________________________________________

Flex Membrane International Corp. 2670 Leiscz’s Bridge Road, Suite 400, Leesport, PA 19533

Tel: [phone] Fax: [phone] www.FlexRoofingSystems.com

Page

2