Flex HE903 User Manual

Product Data Sheet

FLEX HE903 MODIFIED BITUMEN ADHESIVE

PRODUCT DESCRIPTION

Flex HE903 Modified Bitumen Membrane Adhesive is a premium, modified and rubberized, cold process,
waterproofing roofing adhesive which contains low solven content compared with conventional cold applied
adhesives. Designed specificallly for adhering Flex SBS Modified Bitumen and asphalt coated membranes to
properly prepared surfaces.

FEATURES AND BENEFITS

· High solids fibered formulation is modified with SBS rubber polymer, resulting in a high strength bond

when used to adhere Flex SBS Modified Bitumen Membranes and other asphalt based roofing sheets.

· Excellent low temperature flexibility. Roofing can be applied under controlled conditions. The hazard

of torch application, as well as hot asphalt fumes and odors, are eliminated.

· Eliminates the hazard of kettle fires around industrial plants.

· Lap strength adhesion properties far exceed the minimum requirements of ASTM D3019.

· It does not require red label solvent identification.

· Low solvent content, thereby eliminating the potential of softening or damaging SBS membranes.

· VOC Compliant.

PHYSICAL PROPERTIES

Appearnace: Black Fibrous
Aspalt By Weight 45% (ASTM D4479)
Base: Selected Asphalts
Flash Point: 105º F (ASTM D3278)
Freezabiltiy: Will Not Freeze
Lap Peel Strength: 30 lbf/in. min. (ASTM D3019)
Maximum VOC: 250 g/l
Maximum VOS: 2.08 lbs/gal
Solids By Weight 80% +/- 2% (ASTM D4479)
Specific Gravity @ 77º F (25º C): 1.2
Stormer Viscosity: 60-80 (ASTM D4479)
Weight Per Gallon: 9.9-10.4 (ASTM D1475)

PACKAGING

5 Gallon Pails: 53 lbs. each
55 Gallon Drums: 527.5 lbs. each

COVERAGE

100 square feet per 1.5 Gallons

____________________________________________________________________________________________________

Flex Membrane International Corp. 2670 Leiscz’s Bridge Road, Suite 400, Leesport, PA 19533

Tel: [phone] Fax: [phone] www.FlexRoofingSystems.com

Page 1

USES

Flex HE903 Modified Bitumen Adhesive is especially formulated for horizontal applications of roofing plies
and Flex SBS Modified Bitumen Membranes. It has many advantages over the use of hot asphalt in applying
SBS based Modified Bitumen cap sheets such as its compatibility with SBS and BUR roofing memebranes.
Flex HE903 Modified Bitumen Adhesive is ready for use as shipped.

SURFACE PREPARATION

All surfaces to be coated must be dry, clean and free from oil, grease, rust, scale, loose paint and dirt. For
best adhesion over worn or previously coated surfaces, an application of Asphalt Primer is recommended.

APPLICATION

Stir in container and apply by notched squeegee or commercial grade spray equiment. A notched squeegee
with notches 1/4" long, 1/8” deep, spaced on 1” centers, is preferred for smooth surfaces. For irregular
surfaces, the notch should be 1/4" deep. Average application rate over smooth surface is 1.5 gal/100 sq. ft.
Over porous substrates, the coverage rate will increase to approx. 2 gal/100 sq. ft. DO NOT OVER
APPLY. Sufficient adhesive should be applied at laps to result in a visible bead of adhesive at completed lap
edge. Flex SBS modified bitumen should be cut in maximum 18 foot lenghs and membrane allowed to relax
on job site. For best results, it is recommended that the end and side laps be rolled with a weighted roller
immediately after installation. For cold process assemblies, apply uniformly between layers of roofing plies at
the rate of 1.5 to 2 gallons per 100 sq. ft. DO NOT OVER APPLY. For spot application of the first layer
to smooth, non-nailable surfaces, adhere with 9 inch diameter spot application 18 inches o.c. staggered in two
rows.

Flex HE903 Modified Bitumen Adhesive is suitable for spay application using a Garlock Commander with
Hot Max spray rig or a Graco 733 spray rig, or similar. The pump must be able to deliver at least 2000 to
3000 psi. The spray tip must be 0.080” or larger, without a breaker bar. O rings should be made from Viton.
The hose diameter must be at least 3/4” I.D; the last 50 feet can be 1/2" I.D. For hose lengths longer than 200
feet, 1” I.D. is recommended. The product must be at least 70ºF at the tip for spray applications.

IMPORTANT

Flex Modified Bitumen Adhesive does not freeze. Cold weather will cause it to stiffen. Store unopened
container in a warm area at least 24 hours before using. Do not thin. Do not use with Modified Bitumen
Membranes with polyethylene backing. For use with modified bitumen membranes that are sand backed or do
not contain polyethylene or film surfacing.

CLEAN-UP

All equipment can be cleaned with kerosene or mineral spirits. Use care when handling solvents. Clean hands
with a waterless hand cleaner.

CAUTION

Keep out of reach of children. For external use only. Combustible. Contains pertroleum distillate. Keep
away from heat and open flame. Do not heat container or store at temperatures greater than 110ºF. CLOSE
AIR INTAKES on roof until solvents dissipate. Contains volatile solvents that might contaminate potable
water. Close container after use. Dispose of container and unused contents in accordance with Local, State
and Federal regulations.

Flex Membrane International Corp. maintains Material Safety Data Sheets on all of its products. Material
Safety Data Sheets should be read and understood by all supervisory personnel and employees before using
Flex products in your facilities.

____________________________________________________________________________________________________

Flex Membrane International Corp. 2670 Leiscz’s Bridge Road, Suite 400, Leesport, PA 19533

Tel: [phone] Fax: [phone] www.FlexRoofingSystems.com

Page 2