Page 1
Flexiock FLS Roof Edge
Fully Adhered or Mechanically Attached Single-Ply Version
Warranty:
Testing:
Standard Sizes:
Available Materials: Its unique design allows for covers to be manufactured in 24 ga.steel, .040", .050" and .063"
Splice Plates:
The entire roof system is covered under one warranty and inspected after the project is complete to
assure proper installation. The system is inspected after the project is complete to assure proper
installation. This ensures protection for the most vulnerable area of the roof against failure due to
extreme wind up lift pressures.
Tested per ANSI/SPRI ES-1 Standard to comply with the International Building Code.
® FA-SO - FA-80 in 24 ga. steel and .040" aluminum tested to design pressure of 160 Ibs./fF
® FA-50 - FA-80 in .050" and .063" aluminum tested to design pressure of 180 Ibs./fF
® FA-95 - FA-125 in 24 ga. steel and .040" aluminum tested to design pressure of 110 Ibs./fF
® FA-95 - FA-125 in .050" and .063" aluminum tested to design pressure of 140 Ibs./fF
Sizes range to accommodate mrdtiple nailers and coverage requirements.
Product Code Face Height
FA-50 51/4" 1 Nailer
FA-65 6%" 2 Nailers
FA-80 8V4" 3 Nailers
FA-95 9 %"
FA-110 111/4"
FA-125 12 %"
aluminum.
Interlocking, concealed splice plate design prevents splice plate migration under the fascia panels.
This creates a more aesthetically pleasing design compared to traditional cover plates or lap joints at
the seams.
Nailer Coverag<
4 Nailers
5 Nailers
6 Nailers
Watertight: Its non-penetrating design ehminates the need for stripping-in or heat welding that is typical of
many other roof edge designs. Watertight integrity is not compromised by improper flashing
procedures, failed adhesives or lap sealants.
Competitively Priced:
Efficient Design:
Colors:
Custom Capabilities:
Accessories:
Also Included:
The installed cost rivals even light gauge roof edge systems fabricated locally or in a roofers shop.
The fascia is provided in 12'-0" lengths with pre-punched fastening holes in the galvanized
waterdam to ensure correct fastener placement and spacing. The raised button-hole on the vertical
face of the waterdam makes it easier to install.
Choose among a wide range of standard colors and finishes that meet your job requirements. A 20
year Kynar 500® finish warranty is included on standard colors. Custom post-coated Kynar 500
colors are available with an included 10 year Kynar 500 finish warranty or a 20 year Kynar 500 finish
warranty is available upon request. Anodized finishes are also available, but are not warranted.
Radius and specially fabricated products are available to meet the unique needs of each project.
Factory fabricated miters, scuppers and drainage accessories provide a cleaner, more aesthetically
pleasing appearance. This eliminates the need for field fabrication, providing time and labor savings.
All fasteners are included and will arrive to the job site with the product.
features & benefits
44
p: 800-969-0108
1:610-916-9501
Page 2
FLEXLOCK FLS ROOF EDGE
____________________________FULLY ADHERED OR MECHANICALLY ATTACHED SINGLE-PLY VERSION
FA-50 TO FA-80 ANSI/SPRI ES-1 DESIGN PRESSURE OF 160 psf FA-95 TO FA-125 ANSI/SPRI ES-1 DESIGN PRESSURE OF 110 psf
FASCIA COVER (12'-0" [3.65 m] LENGTHS)
• 24 GA. (.65 mm) SPRING CLIP 4'-0" (1.22 m) O.C.
24 GA. (0.65 mm)
GALV. STEEL
NOTES:
FASCIA INCLUDES 3 1/2" (89 mm)
WIDE SPLICE PLATE AT JOINTS.
FASCIA IS TO BE INSTALLED PER SPECIFICATIONS AND FLEX'S
INSTALLATION INSTRUCTIONS DWG. # 28110-11350
FLEXLOCK FLS ROOF EDGE DIMENSIONS
PRODUCT
ID. NO.
□ FA-50
□ FA-65
□ FA-80
□ FA-95
□ FA-110
□ FA-125
Fabrication will proceed only after receipt of
signed print approval.
H
DIM
5 1/4" (133 mm)
6 3/4" (171mm)
8 1/4" (210 mm)
9 3/4" (248 mm)
11 1/4" (286 mm) 8 7/8" (225 mm) 5 NAILERS
12 3/4" (324 mm)
X
DIM
2 7/8"
(73 mm) 1 NAILER
4 3/8"
(111 mm)
5 7/8"
(149 mm) 3 NAILERS
7 3/8"
(187 mm)
10 3/8
' (264 mm)
Print Approval:
Architect and/or contractor shall verify all
dimensions, sizes and quantities. All
products to be installed in strict accordance
with Flex's printed instructions.
Approved by:
Date:
PROJECT:
ARCHITECT:
ROOFING CONTRACTOR:
REPRESENTATIVE/DISTRIBUTOR:
_____
WATERDAM r
FASTEN PRE-PUNCHED WATERDAM 12" (305 mm)
O.C. WITH 1 1/4" (32 mm) GALV. RING SHANK
ROOFING NAILS (PROVIDED)
MATERIAL:
*Oil canning can
occur on larger face
heights. Recommend
.050" (1.27 mm) or .063"
NAILER
COVERAGE
2 NAILERS
4 NAILERS
6 NAILERS
(1.60 mm) for face
heights above
8K" (210 mm).
Color:
Finish:
QUANTITIES:
MEMBRANE
HOLES PRE-PUNCHED 6" (152 mm) O.C.
FASTEN PER JOB REQUIREMENTS.
1 1/4" (32 mm) GALV. RING SHANK
ROOFING NAILS PROVIDED
___
24 Ga. (.65 mm) Galv. Steel*
.040" (T01 mm) Alum.*
___
.050" (1.27 mm) Alum.
___
.063" (1.60 mm) Alum.
OTHER
Lineal Feet 12'-0" (3.65 m) Lengths
. Outside Miter(s) @ (
. Inside Miter(s) @ (_________°)
. Right Endcap(s)
. Left Endcap(s)
, Right Endwall Flashing(s)
Left Endwall Flashing(s)
. Overflow Scupper(s) Style_
, Spillout Scupper(s) Style
Downspout Scupper(s) Style.
(
_____X______
_________
) Size
°)
_______
A: Tapered 1 1/2" (38 mm) Drop
B; Flat
Customer Service: Phone: 800-969^0108 Fax:610-916-9501
DATE: 12/13/10
DRN BY: JJC
CKD BY: SAK
SHT# OF
DWG# 28010-11348
p: 800-969-0108
f: 610-916-9501
print approval
45
Page 3
FLEXLOCK FLS ROOF EDGE
FULLY ADHERED OR MECHANICALLY ATTACHED SINGLE-PLY VERSION
TYPICAL FASCIA ENDCAPS AND ENDWALL FLASHING
detail
46
p: 800-969-0108
f: 610-916-9501
Page 4
FLEXLOCK FLS ROOF EDGE SCUPPERS
FULLY ADHERED OR MECHANICALLY ATTACHED SINGLE-PLY VERSION
SCUPPERS - FACTORY WELDED CONSTRUCTION
p: 800-969-0108
f: 610-916-9501
detail
47
Page 5
FLEXLOCK FLS RADIUS ROOF EDGE
FULLY ADHERED OR MECHANICALLY ATTACHED SINGLE-PLY VERSION
IMPORTANT!
PROVIDING A RADIUS
THE RADIUS MAY BE PROVIDED
IN ONE OF TWO METHODS:
1.) THE ACTUAL KNOWN RADIUS IS
(SMALLEST RADIUS ALLOWED
IS12'-0" [3.65 m])
OR
2.) FIELD CONDITION MEASUREMENTS
NOTE: REFER TO ATTACHED WORKSHEET
MIDPOINT OF
STRAIGHT EDGE
-
-------- ---------
NOTE: CHECK MEASUREMENTS ALONG ENTIRE RADIUS.
36"
(914 mm)
LENGTH OF
STRAIGHT EDGE
DETAIL A
MUST INDICATE PROPER RADIUS CONDITION BY
CIRCLING APPROPRIATE OUTSIDE FACE
(MAX. RISE ALLOWED
IS 1 1/8" [29 mm] ON
36" CHORD)
Fabrication will proceed only after receipt of
signed print approval.
Print Approval:
Architect and/or contractor shall verify all
dimensions, sizes and quantities. All
products to be installed in strict accordance
with Flex's printed instructions.
Approved by:
OUTSIDE
FACE
ROOF LINE
FASCIA
INDICATES AREAS THAT WILL BE SLIT AS
NEEDED TO ACCOMODATE RADIUS
TOP
VIEW
RADIUS
(PROVIDED BY APPROVER
PER DETAIL A)
FLEXLOCK FLS RADIUS ROOF EDGE DIMENSIONS
PRODUCT H X NAILER
ID. NO. DIM DIM
□ FA-50
□ FA-65 6 3/4" (171mm) 4 3/8" (111 mm)
□ FA-80 8 1/4" (210 mm)
□ FA-95
□ FA-110
□ FA-125 12 3/4" (324 mm)
5 1/4" (133 mm)
9 3/4" (248 mm)
11 1/4" (286 mm) 8 7/8"
MATERIAL:
*Oil canning can
occur on larger face
heights. Recommend
.050" (1.27 mm) or .063"
(1.60 mm) for face
heights above
8X" (210 mm)
Color;
Finish:
2 7/8" (73 mm) 1 NAILER
5 7/8"
(149 mm)
7 3/8"
(187 mm)
(225 mm) 5 NAILERS
10 3/8
' (264 mm)
___
24 Ga. (.65 mm) Galv. Steel*
.040" (1.01 mm) Alum.*
___
.050" (1.27 mm) Alum.
___
.063" (1.60 mm) Alum.
OTHER
COVERAGE
2 NAILERS
3 NAILERS
4 NAILERS
6 NAILERS
QUANTITIES
Date:
_
____
PROJECT:
ARCHITECT:
ROOFING CONTRACTOR:
REPRESENTATIVE/DISTRIBUTOR:
print approval
48
Lineal Feet 12'-0" (3.65 m) Lengths
Customer Service: Phone: 800-969^0108 Fax:610-916-9501
DATE: 12/13/10
DRN BY: JJC
CKD BY: SAK
SHT# OF
DWG# 28010-11353
p: 800-969-0108
f: 610-916-9501
D
Loading...