Flex FLE Extended Roof Edge User Manual
Flexiock FLE Extended Roof Edge
Fully Adhered or Mechanically Attached Single-Ply Version
Warranty:
Testing:
Standard Sizes:
Anchor Bar Protection:
Available Materials:
Splice Plates:
The entire roof system is covered under one warranty and inspected after the project is complete to
assure proper installation. The system is inspected after the project is complete to assure proper
installation. This ensures protection for the most vulnerable area of the roof against failure due to
extreme wind up lift pressures.
• Tested per ANSI/SPRI ES-1 Standard to a design pressure of 190 Ibs./fE to comply with the
International Building Code,
• Factory Mutual 1-270 approved for wind up lift protection.
• Miami-Dade Approved (No. 08-0604.02 12/11/13) to comply with the “High Velocity Hurricane
Zone of the Florida Building Code”.
Sizes range from 8 V2" up to 13" face heights to accommodate multiple nailers and coverage
requirements.
• 8 V2
• 10"
• 111/2"
• 13"
The patented, extmded aluminum anchor bar securely terminates the membrane. This provides protection unlike
any other manufactured or shop-fabricated edge. The anchor bar is readily available to dry-in the roof stmcture.
Covers can be manufactured in .050" and .063" aluminum.
Interlocking, concealed splice plate design prevents splice plate migration under the fascia panels.This
creates a more aesthetically pleasing design compared to traditional cover plates or lap joints at the seams.
Watertight:
Competitively Priced:
Efficient Design:
Colors:
Custom Capabilities:
Accessories:
Also Included:
Reusable/Recyclable
Material:
Its non-penetrating design eliminates the need for stripping-in or heat welding that is typical of
many other roof edge designs. Watertight integrity is not compromised by improper flashing
procedures, failed adhesives or lap sealants.
The installed cost rivals even light gauge roof edge systems fabricated locally or in a roofer’s shop.
The product is provided in 12'-0" lengths with pre-punched holes for quicker installation and lower
labor costs. The fastening holes are slotted to allow for proper thermal movement of the materials
and ensure correct fastener placement and spacing.
Choose among a wide range of standard colors and finishes that meet your job requirements. A 20
year Kynar 500® finish warranty is included on standard colors. Custom post-coated Kynar 500
colors are available with an included 10 year Kynar 500 finish warranty or a 20 year Kynar 500 finish
warranty is available upon request. Anodized finishes are also available, but are not warranted.
Radius and specially fabricated products are available to meet the unique needs of each project.
Factory fabricated miters, scuppers and drainage accessories provide a cleaner, more aesthetically
pleasing appearance. This eliminates the need for field fabrication, providing time and labor savings.
All anchor bar EPDM splice plates and fasteners are included and will arrive to the job site with the
product (sealant by others).
When reroofing the anchor bar can be removed, cleaned and reinstalled at any time without
compromising its strength and appearance.
p: 800-969-0108
f: 610-916-9501
features & benefits
33
APPHOVffl
1-270
FLEXLOCK FLE EXTENDED ROOF EDGE
FULLY ADHERED OR MECHANICALLY ATTACHED SINGLE-PLY VERSION
ANSI/SPRI ES-1 DESIGN PRESSURE OF 190 psf
NON-CURING SEALANT
(BY OTHERS)
EXTRUDED
ANCHOR BAR
FLEX
MEMBRANE
12'-0" (3.65 m) LENGTHS
FASCIA COVER
1/ CONTINUOUS CLEAT
Fascia is to be installed per Specifications and Flex's Installation Instructions Dwg. # 28110-3452
FLEXLOCK FLE EXTENDED
ROOF EDGE DIMENSIONS
PRODUa
ID. NO.
□ AEF-85
□ AEF-100
□ AEF-115
□ aEF-130
H
DIM
8 1/2" (216 mm)
10" (251 mm)
11 1/2" (292 mm)
13" (330 mm)
NOA NO. 08-0604.02
MIAMI-DADE COUNTY, FLORIDA
12/11/13
7 1/4" (184 mm)
8 3/4" (222 mm)
10 1/4" (260 mm)
11 3/4" (298 mm)
Fabrication will proceed only after receipt of
signed print approval.
Print Approval:
Architect and/or contractor shall verify all
dimensions, sizes and quantities. All
products to be installed in strict accordance
with Flex's printed instructions.
Approved by:
Date:
__________________
_________________________
20 GA. GALV.
X
DIM
#9 X 2" (51 mm) STAINLESS
STEEL FASTENERS 12" (305 mm) O.C.
PROVIDED BY FLEX
1/4" (6 mm) X 1 1/4" (32 mm) MASONRY/WOOD
FASTENERS 24" (610 mm) O.C. PROVIDED BY
FLEX
NOTE: 3 1/2" (89 mm) SPLICE
PLATES PROVIDED AT ALL
JOINTS
MATERIAL:
___
.050" (1.27 mm) Aluminum
___
.063" (1.60 mm) Aluminum
_ OTHER
Color:
________________
______________________
Finish:
______________________
QUANTITIES:
Lineal Feet (12'-0" (3.65 m) Lengths)
Outside Miters @ (_
Inside Miters @ (
Overflow Scupper
Spillout Scupper
, Downspout Scupper Style
^^^ A: Tapered 1 1/2" (38 mm) Drop
__
___
“)
Style_
Style_
______A____
B: Flat
A B
\
____
B
B
PROJECT:
ARCHITECT:
ROOFING CONTRACTOR:
REPRESENTATIVE/DISTRIBUTOR:
print approval
34
Customer Service; Phone: 800^969-0108 Fax:610-916-9501
DATE: 12/13/10
DRN BY: JJC
CKD BY: SAK
SHT.# OF
DWG# 28010-3170
p: 800-969-0108
f: 610-916-9501
Loading...