Page 1
lease read carefully and save these instructions, as you may need them at a later date.
ASSEMBLY AND INSTALLATION (Continued)
7. Slide the CANOPY (15) and the THREADED RING (16) up the CHAIN (17). Place the CANOPY
(15) over the OUTLET BOX (1) and secure it in place by screwing the THREADED RING (16)
onto the SCREW COLLAR LOOP (6). (See Fig. 1)
8. Slide the CANDLE COVER (23) over the SOCKET (24). Thread THREADED ROD (26) onto the
COUPLING (25), slide the FINIAL PLATE (27) over the THREADED ROD (26), fix with the
FINIAL (28). (See Fig. 2)
9. Screw light bulbs into the lamp sockets and make sure they do not exceed the maximum wattage
specified on the fixture’s wattage rating label, MAXIMUM 60W. (See Fig. 2)
urn off the main power at the circuit breaker before installing the fixture, in order to
CAUTION
revent possible shock.
ll electrical connections must be in accordance with local and National Electrical Code
N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections obtain the
ervices of a qualified electrician.
GENERAL
emove the fixture and the mounting package from the box and make sure that no parts are
issing by referencing the illustrations on the installation instructions.
ASSEMBLY AND INSTALLATION
. Take the parts out of the mounting package. Screw the end of the THREADED ROD (4) into the
center hole of the MOUNTING BRACKET (2) and thread both 1/8” IPS HEX NUT(5) several turns
onto each end of the THREADED ROD (4) but do not tighten the 1/8” IPS HEX NUTS (5). Pull the
SUPPLY WIRES (9 & 11) and the SUPPLY GROUND WIRE (8) out from the OUTLET BOX (1)
and attach the MOUNTING BRACKET (2) assembly to the OUTLET BOX (1) using the slotted
holes of the MOUNTING BRACKET (2) and the MOUNTING SCREWS (3) provided. (See Fig. 1)
. Thread the SCREW COLLAR LOOP (6) onto the bottom end of the THREADED ROD (4). Place
the CANOPY (15) over the OUTLET BOX (1) and adjust the SCREW COLLAR LOOP (6) and
THREADED ROD (4) until the midpoint of the outside threads on the SCREW COLLAR LOOP (6)
is centered (aligned) with the surface of the CANOPY (15). Remove the CANOPY (15) and tighten
both 1/8” IPS HEX NUTS (5) down on the MOUNTING BRACKET (2) and the SCREW COLLAR
LOOP (6). (See Fig. 1)
. Place the COVER (19) over the THREADED ROD (20), thread the FIXTURE LOOP (18) onto the
THREADED ROD (20) until tight. Pull the arms so they are evenly spaced, fix it with the NUT
SCREW (21).
. Open up the end links of the CHAIN (17) and attach one end of the CHAIN (17) onto the FIXTURE
LOOP (18). Slide the THREADED RING (16) and the CANOPY (15) onto the CHAIN (17) (in that
order) and attach the other end of the CHAIN (17) to the SCREW COLLAR LOOP (6). Close the
ends of the chain links. (See Fig. 1 & 2)
INSTALLATION IS NOW COMPLETE
BARRETT PLACE
FIG. 1
FIG. 2
. Unravel the fixture lead wires (10 & 12) and FIXTURE GROUND WIRE (7) and thread them
through every other link of the CHAIN (17) starting with the chain link attached to the FIXTURE
LOOP (18). Feed the fixture lead wires (10 & 12) and FIXTURE GROUND WIRE (7) through the
SCREW COLLAR LOOP (6) and THREADED ROD (4) assembly. Pull the fixture lead wire
(10 & 12) and the FIXTURE GROUND WIRE (7) upward to remove any excess slack. (See Fig. 1)
. Attach the power supply wires to the fixture lead wires by connecting the BLACK SUPPLY WIRE
(9) to the SMOOTH FIXTURE LEAD WIRE (10) and the WHITE SUPPLY WIRE (11) to the
RIBBED FIXTURE LEAD WIRE (12). Loop the FIXTURE GROUND WIRE (7) around the
GROUND SCREW (14) of the MOUNTING BRACKET (2). (Note: Be sure to provide an extra 3”
length of the GROUND WIRE(7).) Connect the remaining FIXTURE GROUND WIRE (7) to the
SUPPLY GROUND WIRE (8) using a WIRE CONNECTOR (13). Place wiring and connections
inside the OUTLET BOX (1). (See Fig. 1)
9-LT FOYER
1. OUTLET BOX
2. MOUNTING BRACKET
3. MOUNTING SCREW
4. THREADED ROD
5. 1/8” IPS HEX NUT
6. SCREW COLLAR LOOP
7. FIXTURE GROUND WIRE
8. SUPPLY GROUND WIRE
9. BLACK SUPPLY WIRE
10. SMOOTH FIXTURE LEAD
WIRE
11. WHITE SUPPLY WIRE
12. RIBBED FIXTURE LEAD
WIRE
13. WIRE CONNECTOR
14. GROUND SCREW
15. CANOPY
16. THREADED RING
17. CHAIN
18. FIXTURE LOOP
19. COVER
20. THREADED ROD
21. NUT SCREW
22. ARM
23. CANDLE COVER
24. SOCKET
25. COUPLING
26. THREADED ROD
27. FINIAL PLATE
28. FINIAL
Page 2
Lighting Limited Warranty
We warrant all our Products to be free from defects in material and workmanship, subject to certain conditions and exclusions, for period of one year from the date the
Product was shipped to the original end use purchaser. We will warranty its product only if it is sold through an our authorized dealer.We will, at its discretion, repair,
replace or make appropriate adjustment where inspection discloses any defects occurring in normal usage within the applicable time period above, subject to the
following conditions and exclusions.
The following costs, expenses and damages are not covered by the provisions of this limited warranty: (1.) labor costs including, but not limited to, costs associated
with the removal and reinstallation of Product; (2.) shipping and freight expenses required to return Product to us.
CARE & CLEANING: Initial care for finishes requires periodic cleaning with a soft cloth, dampened with water. A mild non-abrasive soap may be used along with
a soft cloth and water if the fixture is very dirty. Particular care should be taken to avoid abrasive materials and strong cleaning agents as they will quickly destroy the
protective coatings and subject the finish to oxidation and discoloration.
Loading...