Flavel Linear Pebble Installation And Maintenance Instructions Manual

Supplied By www.heating spares.co Tel. [phone]

Linear Pebble

DECORATIVE PEBBLE FUEL EFFECT GAS FIRE

Installation and Maintenance Instructions
Hand these instructions to the user

Model No’s FRDPU0MN are for use on Natural Gas (G20) at a supply
pressure of 20 mbar in G.B. / I.E.

Supplied By www.heating spares.co Tel. [phone]

CONTENTS

Section 1 Information and Requirements PAGE

1.0 Appliance Information 3

1.1 Conditions of Installation 4

1.2 Flue and chimney suitability 4

1.3 Fireplace / surround suitability 5

1.4 Shelf position 5

1.5 Chimney inspection 5

1.6 Fire place opening / catchment space 6-7

1.7 Precast Flues 8

1.8 Metal Flue boxes 8

1.9 Hearths 8

1.10 Spillage Monitoring System 9

Section 2 Installation of Fire

2.1 Unpacking the fire 10

2.2 Installing the fire box 10-15

2.3 Gas soundness and burner pressure 16

Section 3 Assembling Fuel Bed and Commissioning

3.1 Assembling the ceramics and fuel bed 16-19

3.2 Lighting the appliance 20

3.3 Checking for clearance of combustion
products 20-21

Section 4 Maintenance

4.1 Removal of the Burner Assembly 22

4.2 Removal of the Piezo Igniter 22

4.3 Removal of the Control Tap 23

4.4 Removal of the Pilot Assembly 23

This appliance is manufactured by:­CFM Europe Ltd,

Trentham Lakes,
Stoke-on-Trent, ST4 4TJ

2

Supplied By www.heating spares.co Tel. [phone]

SECTION 1

INFORMA TION AND REQUIREMENTS

1.0 APPLIANCE INFORMATION

Model FRDPU0MN
Gas Type G20

Main injectors (2 off) Size 260
Pilot Type Copreci Single Flame

21100 / 141

Max. Gross Heat Input : 6.9 kW
Min. Gross Heat Input : 4.2 kW

Cold Pressure : 20.0 +/-1.0 mbar
Ignition : Push-button Piezo
Electrode Spark Gap 4.5mm
Packed Weight (without fender) 15 kg

Fire box Dimensions (with linear trim fitted)

Width : (with linear trim, no spacer) 484mm
Height : (with linear trim, no spacer) 595mm
Depth : (from mounting face to rear panel without spacer fitted) 170mm
Depth : (from mounting face to rear panel with spacer fitted) 120mm

Gas Connection : 8mm Compression (Supplied with fire)

3

Supplied By www.heating spares.co Tel. [phone]

INSTALLATION REQUIREMENTS

1.1 CONDITIONS OF INSTALLATION

It is the law that all gas appliances are installed only by a CORGI Registered
Installer, in accordance with these installation instructions and the Gas Safety
(Installation and Use) Regulations 1998 as amended. Failure to install appliances
correctly could lead to prosecution. It is in your own interest and that of safety to
comply with the law.

The installation must also be in accordance with all relevant parts of the Local and
National Building Regulations where appropriate, the Building Regulations
(Scotland Consolidation) issued by the Scottish Development Department, and all
applicable requirements of the following British Standard Code of Practice.

1. B.S. 5871 Part 3 Installation of Decorative Fuel Effect Gas Fires

2. B.S. 6891 Installation of Gas Pipework

3. B.S. 5440 Parts 1 & 2 Installation of Flues and Ventilation

4. B.S. 1251 Open fire place components

5. B.S. 715 Metal flue pipes for gas appliances

6. B.S. 6461 Part 1 Installation of Chimneys and flues

7. B.S. E.N. 1858 Chinmeys Components & Concrete Flue Blocks

8. I.S. 813 : 1996 Domestic Gas Installation (Republic of Ireland)

No purpose made additional ventilation is normally required for this appli­ance, when installed in G.B. When Installing in I.E. please consult document
I.S. 813 : 1996 Domestic Gas Installation, which is issued by the National
Standards Authority of Ireland. If installing in Northern Ireland, please
consult local building regulations. Any purpose made ventilation must be
checked periodically to ensure that it is free from obstruction.

1.2 FLUE AND CHIMNEY SUITABILITY

This appliance is designed for use with conventional brick built or lined chimneys
and fabricated flues. It is also suitable for use with pre-cast flue blocks conforming
to BS EN 1858 and metal flue boxes conforming to BS 715. All flues must
conform to the following minimum dimensions.

Minimum diameter of circular flues 125 mm (Without Flue

Restrictor Fitted)

Minimum effective height of all flue types 3 metres

When fitting to conventional chimneys or 175mm flues it may be desirable to
fit the flue restrictor baffle (supplied) to reduce the flue flow and increase the
efficiency of the fire. Safe clearance of products must always be checked by
carrying out a smoke match test as described.

4

Supplied By www.heating spares.co Tel. [phone]

1.3 FIREPLACE / SURROUND SUITABILITY

The fire must only be installed on a hearth it must not be installed directly onto
carpet or other combustible floor materials.

The fire is suitable for fitting to non-combustible fire place surrounds and propri­etary fire place surrounds with a temperature rating of at least 150oc.

If a heating appliance is fitted directly against a wall without the use of a fire
surround or fire place all combustible material must be removed from behind
the trim. Soft wall coverings such as blown vinyl, wall paper etc. could be
affected by the rising hot air and scorching and/or discoloration may result.
Due consideration should be made to this when installing or decorating.

1.4 SHELF POSITION

The fire may be fitted below a combustible shelf providing there is a minimum
distance of 200mm above the top of the fire and the shelf does not project more
than 150mm. If the shelf overhangs more than 150mm the distance between the
fire and the shelf must be increased by 15mm for every 25mm of additional
overhang over 150mm.

1.5 FLUE / CHIMNEY INSPECTION

Before commencing installation, a flue or chimney should be inspected to ensure
that all the following conditions are satisfied.

1. Check that the chimney / flue only serves one fire place and is clear of any
obstruction. Any dampers or register plates must be removed or locked in
the open position.

2. Brick/stone built chimneys or any chimney or flue which has been used for
an appliance burning fuel other than gas must be thoroughly swept. The
base of the chimney / flue must also be thoroughly cleared of debris etc.

3. Any under-floor air supply to the fire place must be completely sealed off.

4. Ensure that the inside of the chimney / flue is in good condition along it’s
length and check that there is no leakage of smoke through the structure
of the chimney during and after the smoke pellet test. With pre-cast flues

it is especially important to check the inside of the flue for extruded
cement / sealant protruding from the joints between the flue
blocks. If present, these should be removed by rodding the flue
before proceeding with the installation.

5. Using a smoke pellet, check that there is an up-draught in the
chimney / flue and that the smoke can be seen issuing from the
terminal / chimney pot outside.

5

Supplied By www.heating spares.co Tel. [phone]

There must be no leakage of smoke through the structure of
the chimney during or after the smoke pellet test and it is
important to check inside upstairs rooms adjacent to the chimney /
flue. Check the chimney pot / terminal and general condition of the

brickwork or masonry. If the chimney or flue is in poor condition or if
there is no up-draught do not proceed with the installation. If there is a
history of down-draught conditions with the chimney / flue, a tested and
certificated flue terminal or cowl suitable for the relevant flue type should
be considered.

6. A spillage test must always be carried out during commissioning of

the appliance.

1.6 FIRE PLACE OPENING AND CHIMNEY CATCHMENT SPACE

The front opening of the fire place must be between 375 and 440 mm wide, and
between 550 and 570mm high. If the opening exceeds these dimensions then a
surround must be constructed from suitable non-combustible material to produce a
correct size opening. Any surround must be suitably sealed to the fire place to
prevent leakage. See below in fig.1

When installing into a brick built chimney, you must ensure that there is sufficient
depth to accomodate any debris which may fall from the chimney. This depth
must be sufficient to accomodate 12 litres of volumetric space.

Fire Opening

375mm Minimum
440mm Maximum

610mm
Minimum

520mm Minimum

Fig. 1

550mm Minimum
570mm Maximum

Minimum Flat
Sealing Area

6

Supplied By www.heating spares.co Tel. [phone]

Table A - Installation Depth Requirements for a Flavel Linear Pebble being
installed into a brick built chimney, requiring 12.0 litres of debris collection
volume (fig. 2).

When installing this product into a builders opening / brick-built chimney, the depth
required is a minimum of 170mm. The 12.0 litres of debris collection volume is
achieved by the space available taper down the sides of the firebox. This depth
can be reduced to 120mm if the black 50mm spacer frame is used. This spacer
frame can be purchased from CFM Europe Ltd. as an optional extra.
This appliance is suitable for use in fireplaces fitted with an existing chairbrick
without the need for removal of the chairbrick, providing the minimum depth of the
fireplace exceeds 260mm. If the depth is less than 260mm then the spacer
(optional) must be used to give a minimum clearance from the rear of the fire to
the rear of the chairbrick of at least 90mm to allow sufficient space for the
collection of debris which may fall down the chimney. The fireplace must be
checked to ensure that no part of the chairbrick is within 50mm of the flue outlet of
the fire when installed.

For example, if the appliance was to be fitted into a 400mm wide opening, the
depth required would be 170mm. See fig. 2 below for explanatory diagram.

Fig. 2

7

Opening Width ( e.g. 400mm)

Depth Required

(e.g. 170mm)

Supplied By www.heating spares.co Tel. [phone]

1.7 FITTING TO PRE-CAST FLUE INSTALLATIONS

When installing this appliance into pre-cast flues, always ensure that the
spigot restrictor baffle has been removed.
To install the fire box in to pre-cast flue starter blocks, there must be at least
170mm from the mounting face of the fire to the rear of the pre-cast flue
starter block to allow sufficient space for debris collection. It is important to

consider this depth when choosing a fire surround as the thickness of the fire
surround must be sufficient to give a total depth of at least 170 mm to the rear of
the starter block, otherwise there will be insufficient depth. To increase this depth
the optional black 50mm spacer frame may be purchased, this will reduce the
depth required to 120mm or the fire surround may be packed away from the wall
using suitable non-combustible board, providing the installation is correctly sealed.
If in doubt about the suitability of the fire contact CFM Europe Ltd. for advice
before proceeding. This fire has been designed to fit standard 100mm pre-

cast starter blocks with 3 inch rebated surrounds.

It is important to ensure that the pre-cast flue is in good condition and is free from
extruded mortar or sealant from between the flue blocks.

This appliance has been tested for use in a pre-cast flue block complying
with BS EN 1858. In accordance with BS EN 1858, pre-cast flues built with
directly plastered faces (front or rear) are not correctly installed as to ensure
proper operation with any type of gas fire. In some instances of this flue
construction, temperature cracking of surface plaster may occur through no
fault of the appliance. An air gap or some form of insulation material should
be installed to prevent normal flue temperatures from damaging wall
surfaces.

1.8 FITTING TO PRE-FABRICATED TWIN WALL METAL FLUE BOXES

The appliance may be fitted to twin wall metal flue boxes conforming to the con­structional requirements of BS 715, (for example the Selkirk LFE 125 box). The
box must have a minimum flue diameter of 125mm internal and minimum internal
dimensions of 160mm deep by 580mm high by 350mm wide. There are no maxi­mum dimensional requirements for the box. The top face of the box must be
insulated with a minimum thickness of 50mm of non-combustible mineral wool
insulation or similar material. The flue box must stand on a non-combustible base
of minimum thickness 12mm.

1.9 HEARTHS

This appliance must only be installed on to a concrete or non-combustible hearth.
The hearth material must be a minimum thickness of 12mm with the top surface at
least 50mm above the floor. The hearth must be fitted symmetrically about the fire
opening and have a minimum width of 760mm and a minimum projection of
300mm forwards from the fire opening. If the black spacer frame is used, the
hearth projection forward from the fireplace opening will require to be 350mm.

8

Supplied By www.heating spares.co Tel. [phone]

1.10 SPILLAGE MONITORING SYSTEM

This appliance is fitted with an atmosphere sensing spillage monitoring system in
the form of an oxygen sensing pilot. This is designed to shut the fire off in the
event of a partial or complete blockage of the flue causing a build up of combus­tion products in the room in which the fire is operated. The following are impor-
tant warnings relating to this spillage monitoring system :-

1) The spillage monitoring system must not be adjusted by the installer.

2) The spillage monitoring system must not be put out of operation.

3) When the spillage monitoring system is exchanged only a complete original

manufacturers part may be fitted. It is not possible to replace individual parts on
the pilot system on this appliance, only a complete pilot assembly (including the
thermocouple) may be fitted.

9

Supplied By www.heating spares.co Tel. [phone]

SECTION 2

INSTALLATION OF FIRE

2.1 UNPACKING THE FIRE

Carefully lift the fire out of the carton. Remove the loose item packaging carefully
from the front of the appliance. Check the contents as listed :-

Packing Check List
1off Fire box / burner assembly

1off Boxed pebble base, ceramic front rail and 14 synthetic pebbles
1off Loose items bag.
1off Cable Fixing Kit
1off Linear trim
1off each User instruction book and Installation book
1off Linear Ashpan

2.2 INSTALLING THE FIRE BOX

Establish which type of flue you are intending to install the fire in to :-

225 x 225mm (9 inch x 9 inch) brick built chimneys
175mm (7 inch) diameter lined brick or stone flue, or insulated pre-fabricated
metal flue box to B.S. 715.

When installing into 125mm (5 inch) diameter lined brick or stone flue, or
insulated pre-fabricated metal flue box to B.S. 715 and pre-cast flues the
restrictor baffle must not be fitted.

A spillage test must always be carried out to check satisfactory
clearance of flue products, regardless of the type of flue the
appliance is being fitted to.

10

Supplied By www.heating spares.co Tel. [phone]

Proceed as follows :-

a) Remove the Linear trim. Remove the burner heat shield from the

front of the fire box to allow access to the burner. See fig. 3 below.

Fig. 3

b) Ensure that the hearth is protected from damage and carefully lift the

fire box into the fire opening, then slide it back into position. Check that
the fire box flange fits flush to the sealing face of the fire surround or
wall with no gaps present.

c) Remove the four retaining screws securing the burner to the firebox.

The base of the burner unit can now be pulled forward, allowing the
burner to be removed from the fire box. See fig. 4 below.

Fig. 4

11

Supplied By www.heating spares.co Tel. [phone]

d) Whilst the fire box is still in position, decide which side the gas supply is

to enter the fire from. If concealed pipe work is required plan the pipe
run to enter the fire box through one of the openings in the sides of the
fire box below the fuelbed support panel and connect to the isolating /
inlet elbow. The gas connection to the appliance should be made to the
isolating / inlet elbow using 8mm rigid tubing. There must be no
soldered joints within the firebox. See fig. 5 & 6 below for suggested
concealed pipe layouts.

Fig. 5

Fig. 6

Note : Before breaking into the gas supply a pressure drop test should be
carried out to establish that the existing pipework is sound.

Carefully withdraw the fire box from the opening to enable the gas supply and fire
fixing to be completed.

12

Firebox

Approx.
40mm

Fireplace

Gas Supply

Firebox

Approx.
40mm

Fireplace

Gas Supply

Supplied By www.heating spares.co Tel. [phone]

Depending on the spacer option selected, (flush fit or 50mm black spacer) there is
a choice of methods of fixing the firebox which are provided to enable the installer
to deal with any type of installation.

The preferred method of fixing which is suitable for almost all situations is
the cable fixing method which is described in the following section in detail.

If the 50mm black spacer is used, the fire may be secured using the cable method
as described below, or alternatively, in installations where the cable method is not
suitable (eg. loose masonary in rear of fire opening) the fire box may be secured
to the fire surround using screws which are supplied. The foam seal (supplied)
must be fitted around the perimeter of the spacer in a “goalpost” arrangement to
ensure a seal is achieved to the fireplace.

To fit using the preferred cable method proceed as follows­e) Mark out and drill 4 off No 14 (6mm) holes in the back face of the fire

opening in the positions shown below in fig. 7

Fig. 7

Fit the wallplugs provided and screw the fixing eyes securely into the rear of the
fire opening. If the clearance at the rear of the fire is at the minimum specified for
a precast flue application, it may be necessary to bend over the lower fixing eyes
after screwing them fully in to the rear of a pre-cast starter block.

f) Uncoil the two fire fixing cables and thread one end of each of the

cables through one of the two holes on each side of the flue outlet
shroud.

13

Fireplace Opening

325mm

100mm

500mm

20mm

Supplied By www.heating spares.co Tel. [phone]

g) Position the fire carefully on the (protected) surface of the hearth and

reach into the fire opening. Thread each of the cables vertically
downwards through the pair of fixing eyes on the same side of the fire.
Thread the free end of the cables through the corresponding circular
hole on each side of the lower rear of the fire. Carefully slide the fire
box back into the fire opening and pull both cables tight.

h) Thread a tensioning screw over each of the cables and ensure that the

tensioning nut is screwed fully up against the hexagon shoulder of the
tensioning screw (this provides maximum travel for the tensioning nut).

i) Fit a screwed nipple on to each of the cables and pull hand tight up

against the tensioning screw, then secure each nipple with a flat
bladed screwdriver. See fig. 8 below

Fig. 8

j) Evenly tighten the tensioning nuts to tension both cables and pull the

fire snugly against the wall. Do not overtighten, it is only necessary to
pull the seal up against the sealing face of the wall, it does not need to
be compressed. Check that there are no gaps behind the seal.

k) With the fire securely in place, if a concealed gas connection has been

made through either of the access holes in the sides of the fire, the
holes should be closed around the pipe to prevent leakage of air
through the gap around the pipe.

l) Refit the burner. Fit the four retaining screws and check that the burner

is correctly locked into position.

14

Supplied By www.heating spares.co Tel. [phone]

m) Refit the front burner heat shield to the sides of the fire box (2 Screws)

and secure the linear trim to the fire using the magnets
provided.

n) Before making the final gas connection, thoroughly purge the gas

supply pipework to remove all foreign matter, otherwise serious
damage may be caused to the gas control valve on the fire.

The other firebox fixing method is as follows :­In installations where the cable method is not suitable (e.g. loose masonary in rear

of fire opening) the firebox can be secured to the fire surround using four screws
and wall plugs provided. Below (fig.9) is a diagram to indicate the hole centre
positions available on the firebox to facilitate the screw fixing to the fireplace /
surround.

Fig. 9

On Linear models, the installer must fit the ashpan knob to the ashpan using
the fixing screw provided. The ashpan is packed in the side fittings of the
main packaging.

260mm

37mm

532mm

425mm

Firebox
Mounting
Flange

15

Supplied By www.heating spares.co Tel. [phone]

2.3 GAS TIGHTNESS AND INLET PRESSURE

a) Remove the pressure test point screw from the inlet elbow and fit a

manometer.
b) Turn on the main gas supply and carry out a gas tightness test.
c) Depress the control knob and turn anti-clockwise to the position marked

pilot. Hold in the control knob for a few seconds to purge the pipe work

then press the igniter button. The burner should light, continue to hold

the control knob for a few seconds then turn to the full-on position.
d) Check that the gas pressure is 20.0 mbar (+/- 1.0mbar) 8.0 in w.g.(+/-

0.4 in w.g.)

e) Turn off the fire, remove the manometer and refit the pressure test point

screw. Check the pressure test point screw for gas tightness with the

appliance turned on using a suitable leak detection fluid or detector.

SECTION 3

ASSEMBLING FUEL BED AND COMMISSIONING

3.1 ASSEMBLING THE CERAMICS AND FUEL BED

a) Place the ribbed ceramic fuelbed base on top of the fuelbed support

and pull fully forwards to the burner. Make sure that the fuelbed

base is located centrally in the fire box. Ensure that the fuelbed

base fit fully down onto the fuel bed support and is not

lodged on the burner. See fig. 10 below.
Fig. 10

16

Supplied By www.heating spares.co Tel. [phone]

b) Position front ceramic rail on burner front ceramic support and ensure

that the locating channel in the front ceramic rail is correctly located

onto the lip on the burner front ceramic support. (See fig. 11 below)

Fig. 11

c) Pick pebbles Ato E and arrange along the the front rail, ensuring that

they are evenly spaced. Use the recess’s in the front ceramic rail as a

guide for placement. (See fig. 12 below)

Fig. 12

17

Pebble A
Pebble B

Pebble C
Pebble D
Pebble E

Supplied By www.heating spares.co Tel. [phone]

d) Select pebbles F to I and arrange behind the front row of pebbles,

ensuring that flame paths as indicated below are not interupted.
. (See fig. 13 below)

Fig. 13

e) Select pebbles K, L & M and arrange along the rear of the

fuelbed, using the ribs in the rear of the fuelbed as a guide for

placement. (See fig. 14 below)

Fig. 14

f) Select the two small pebbles (J & N) and position to fill the gaps at each

end of the third row of pebbles, as shown above in Fig. 14

18

Pebble F
Pebble G

Pebble H
Pebble I

Pebble K

Pebble M
Pebble L

Pebble J

Pebble N

Supplied By www.heating spares.co Tel. [phone]

The exact position and fit of the pebbles may be finely adjusted to give the most
pleasing and random appearance.

Warning : Use only the pebbles supplied with the fire. When replacing the

pebbles remove the old pebbles and discard them. Fit a complete

set of pebbles of the correct type. Do not fit additional pebbles or

any pebbles other than a genuine replacement set.

This appliance uses fuel effect pieces containing Refractory Ceramic Fibres
(R.C.F.), which are man-made vitreous silicate fibres. Excessive exposure to
these materials may cause temporary irritation to eyes, skin and respiratory
tract. Consequently, it makes sense to take care when handling these
articles to ensure that the release of dust is kept to a minimum. To ensure
that the release of fibres from these R.C.F. articles is kept to a minimum, dur­ing installation & servicing we recommend that you use a HEPAfiltered
vacuum to remove any dust and soot accumulated in and around the fire,
before and after working on the fire. When replacing these articles we rec­ommend that the replaced items are not broken up, but are sealed within a
heavy duty polythene bag, clearly labelled as “RCF waste”. This is not
classified as “hazardous waste” and may be disposed of at a tipping site
licensed for the disposal of industrial waste. Protective clothing is not
required when handling these arrticles, but we do recommend you follow the
normal hygiene rules of not smoking, eating or drinking in the work area,
and always wash your hands before eating or drinking.

This appliance does not contain any component manufactured from
asbestos or asbestos related products.

19

Supplied By www.heating spares.co Tel. [phone]

3.2 LIGHTING THE APPLIANCE

a) Turn on the gas isolation tap.
b) Depress the control knob and turn anti-clockwise to the position

marked pilot. Hold in the control knob for a few seconds to purge the

pipe work.
c) Continue to hold-in the control knob and press the igniter button. If the

burner does not light, continue to press the igniter button until ignition

occurs. Continue to hold the control knob for 5-10 seconds to allow the

thermocouple to heat up, if the pilot goes out when the control knob is

released, repeat the lighting sequence.
d) Turn the control knob in the anti-clockwise direction to the high position

and the main burner will light.
e) Turn the control knob clockwise to the low position and the gas input

will be reduced to the minimum setting.
f) Slightly depress the control knob and turn to the pilot position, the main

burner will go out but the pilot will remain lit.
g) Slightly depress the control knob and turn to the off position, the pilot

will now be extinguished.

WARNING :If the fire goes out for any reason or is turned off and it

is necessary to re-light the fire it is important to allow the
fire to cool for 3 minutes before attempting to re-light it.

3.3 CHECKING FOR CLEARANCE OF COMBUSTION PRODUCTS

a) Close all doors and windows in the room.
b) Light the fire and allow to run for approximately 5 minutes on high

position.
c) After approximately 5 minutes hold a smoke match just inside and

below the centre of the lower front edge of the top of the fire. (It is

recommended that a suitable smoke match holder is used when check

ing for clearance of combustion products). All smoke generated should

be drawn back into the flue. If slight spillage occurs or if in doubt,

repeat the test after a further 5-10 minutes. If the test indicates that

spillage is occurring and the flue restrictor baffle has been fitted, it

should be removed and the test repeated after the fire has cooled.

20

Supplied By www.heating spares.co Tel. [phone]

d) If spillage persists, the flue is not functioning correctly and a fault exists.

If, after investigation the fault cannot be traced and rectified, the fire

must be disconnected from the gas supply and expert advice obtained.
e) If there is an extractor fan fitted any where in the vicinity of the

appliance, the spillage test should be repeated with the fan running on

maximum and all interconnecting doors open.
f) After ensuring that the fire is safe to use it should be left on high

position to fully warm up. During this time a slight odour may be

noticed, this is due to the “newness” of the fire and will soon disappear.

At this stage any minor adjustments to the pebbles should be made

using suitable long handled tongs and taking care not to damage the

pebbles.

Finally, hand the Installation and Maintenance Instructions and the

Users Instructions over to the customer and explain the operation of the

fire.

21

Supplied By www.heating spares.co Tel. [phone]

SECTION 4

MAINTENANCE

Servicing Notes

Servicing should be carried out annually by a competent person such as a CORGI
registered engineer. This is a condition of the Flavel guarantee schemes.
The service should include visually checking the chimney and fire opening for
accumulations of debris and a smoke test to check for a positive up-draught in the
chimney.
The condition of the pebbles should be checked and if necessary the whole set

should be replaced with a genuine replacement set.

The burner assembly is designed to be removed as a complete unit for ease of
access. After any servicing work a gas tightness check must always be car-

ried out.

For Diagrams refer to Section 2

4.1 Removing the burner assembly from the fire.

4.1.1 Prepare work area (lay down dust sheets etc.)

4.1.2 Lift the Linear trim and ash pan cover out of the way and put

them in a safe location. Remove the loose pebbles from the fuel bed

and front ceramic rail. Remove the front ceramic from the rail. Unscrew

the two pozi-driv fixing screws which secure the burner heat shield and

remove it from the fire.

4.1.3 Isolate the gas supply and remove the inlet pipe from the appliance

inlet elbow. Unscrew and remove the four screws which retain the

burner. Remove the burner assembly from the fire.

4.1.4 To refit the burner assembly. Push the base of the control panel fully

into the fire and secure with the four screws. Refit the gas supply pipe

and carry out a gas tightness test. Refit the burner heat shield then

refit the pebbles referring to section 3 for the correct layout. The

Linear trim and ash pan cover can now be re-positioned.

4.2 Removing the Piezo Igniter

4.2.1 Remove the burner assembly as in section 4.1

4.2.2 Disconnect the ignition lead from the piezo and unscrew the

retaining nut on the rear of the control panel. Withdraw the piezo from

the front of the control panel. Re-assemble in reverse order and carry

out a gas tightness test.

22

Supplied By www.heating spares.co Tel. [phone]

4.3 Removing the Control Tap from the fire.

4.3.1 Remove the burner assembly as in section 4.1.

4.3.2 Pull the control knob off the control tap spindle.

4.3.3 Loosen and remove the three gas pipe retaining nuts from the control

tap and release the ends of the gas pipes from the control tap body.

Loosen and remove the thermocouple securing nut from the end of the

control tap.

4.3.4 Unscrew the control tap locknut from the front of the control panel and

remove the control tap.

4.3.5 To refit a control tap, reassemble in reverse order noting that the control

tap locates with a flat in the control panel. Carry out a gas tightness

test after re-assembly.

4.4 Removing the Oxy-Pilot Assembly

Note : Because this appliance is fitted with an atmosphere sensing ‘Oxy­Pilot’ it is not possible to replace the thermocouple separately, because the
thermocouple position is factory set to a tight tolerance. Any replacement of
parts on the pilot requires a complete new pilot assembly.

4.4.1 Remove the burner assembly as in section 4.1

4.4.2 Unscrew and remove the thermocouple retaining nut from the end of the

control tap and disconnect the ignition lead from the pilot electrode.

4.4.3 Unscrew and remove the two pozi-driv screws which secure the pilot

assembly to the burner. Remove the pilot.

4.4.4 Re-assemble in reverse order and carry out a gas tightness test.

23

Supplied By www.heating spares.co Tel. [phone]

PARTS SHORTLIST

Replacement of any other parts must be carried out by a competent person such
as a CORGI registered gas installer. The part numbers of the replaceable parts
are as follows, these are available from CFM Europe Ltd. who may be contacted
at the address shown below.

Fuelbed base B-77260
Fuelbed front rail B-58140
Replacement pebble set B-77250
L/H Fibre Board B-68930
R/H Fibre Board B-68940
Upper Rear Fibre Board B-68910
Lower Rear Fibre Board B-68920
Piezo Igniter B-1320
Ignition Wire B-39030
Gas Valve B-36990

This appliance must only be used with the Linear trim and ashpan
supplied

Due to our policy of continual improvement and development the exact
accuracy of illustrations and descriptions contained in this book cannot be
guaranteed

Part No. B-60310

Issue 5

CFM Europe Ltd.

Trentham Lakes

Stoke-on-Trent

Staffordshire

ST4 4TJ

www.cfm-europe.com

Telephone - General Enquiries : [phone]
Telephone - Service : [phone]