FlashLogic FLC-AL-CH4, FLC-ALDL-CH4 Install Manual

!

Audiovox Electronics Corp.

INSTALL GUIDE

CH4

flc-al(Dl)-ch4

available for : flcaN

Rev. Date: March 28, 2012 Doc. No.: ##9016## 20120328

PLEASE VISIT www.flash-it.com FOR COMPLETE PRODUCT DETAILS

NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiﬁed technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.

XX-XX PAGE X-X

ADS-AL(DL)-CH4 PAGE 2-4

INSTALL GUIDE

ALL IN ONE

Chrysler/DoDge/Jeep

Page 2 of 9 FLC-AL(DL)-CH4 20120328

Doc. No.: ##9016##

INSTALL TYPE SELECTION

FEATURES

MAKE

300 08-11 1 or 2 • • • • • • • • • • • • • • • • 300 Limited 08-11 1 or 2 • • • • • • • • • • • • • • • • 300c 08-11 1 or 2 • • • • • • • • • • • • • • • • 300c SRT8 08-11 1 or 2 • • • • • • • • • • • • • • • •

CHRYSLER

Town & Country 08-12 1 or 2 • • • • • • • • • • • • • • • • • • • • • Caravan 08-10 1 or 2 • • • • • • • • • • • • • • • • • • • • • Challenger SXT 08-11 1 or 2 • • • • • • • • • • • • • • • • • • Challenger R/T 08-11 1 or 2 • • • • • • • • • • • • • • • • • • Challenger SRT8 08-11 1 or 2 • • • • • • • • • • • • • • • • • • Charger SE 08-11 1 or 2 • • • • • • • • • • • • • • • • Charger R/T 08-11 1 or 2 • • • • • • • • • • • • • • • • Charger SRT8 08-11 1 or 2 • • • • • • • • • • • • • • • • Durango 11 1 or 2 • • • • • • • • • • • • • • • •

DODGE

Grand Caravan 08-12 1 or 2 • • • • • • • • • • • • • • • • • • • • • Journey 09-10 1 or 2 • • • • • • • • • • • • • • • • • Magnum 08 1 or 2 • • • • • • • • • • • • • • • • RAM 1500 09-12 1 or 2 • • • • • • • • • • • • • • • RAM 2500 10-12 1 or 2 • • • • • • • • • • • • • • • RAM 3500 10-12 1 or 2 • • • • • • Commander 08-10 1 or 2 • • • • • • • • • • • • • • •

JEEP

Grand Cherokee 08-11 1 or 2 • • • • • • • • • • • • • • • C/V 10-12 1 or 2 • • • • • • • • • • • • • • • • • • • • • 1500 10-12 1 or 2 • • • • • • • • • • • • • • •

RAM

2500 10-12 1 or 2 • • • • • • • • • • • • • • • 3500 10-12 1 or 2 • • • • • • • • • • • • • • •

MODEL

YEAR

INSTALL TYPE

DATA IMMOBILIZER BYPASS

DOWNLOADABLE SOFTWARE

RS232 COMMUNICATION

2-WAY COMPATIBILITY

PRIORITY UNLOCK

DOOR LOCK

DOOR UNLOCK

ARM OEM ALARM

DISARM OEM ALARM

TRUNK/HATCH RELEASE

POWER LIFTGATE

POWER SLIDING DOOR (L)

POWER SLIDING DOOR (R)

DOOR STAT OUTPUT

TRUNK STAT OUTPUT

RAP SHUTDOWN CTRL

BRAKE PEDAL STAT OUTPUT

E-BRAKE OUTPUT

TACHOMETER OUTPUT

• • • • • • • • •

DATA/MUX IGNITION CTRL

SECURE TAKEOVER

PARKING LIGHT CTRL

Routan 09-12 1 or 2 • • • • • • • • • • • • • • • • • • • • •

VOLKSWAGEN

Visit our website for advanced features.

INSTALL GUIDE

ALL IN ONE

Chrysler/DoDge/Jeep

Page 3 of 9 FLC-AL(DL)-CH4 20120328

Doc. No.: ##9016##

TYPE 1 - WIRING DIAGRAM

DRIVER DOOR PIN

REFER TO

ASSEMBLY FOR PROPER

CONNECTIONS AND MATCH

!

EACH LETTER ACCORDINGLY

GWR (-) INPUT - BLUE/WHITE

VEHICLE (-)

LEGEND

N/A

NOT REQUIRED IN DATA MODE (1-WAY) NOT REQUIRED IN DATA MODE (2-WAY)

USE DATA MODE

OR HARDWIRE MODE

DATA MODE

(NC) WHITE

(NC) BLACK

(NC) RED

LOCK/ARM (-) INPUT - GREEN/BLACK

UNLOCK/DISARM (-) INPUT - BLUE/BLACK

LEFT SLIDING DOOR (-) INPUT - PURPLE/YELLOW

RIGHT SLIDING DOOR (-) INPUT - PURPLE/BLACK

TRUNK (-) INPUT - RED/WHITE

DISARM ONLY (-) INPUT - BROWN

PARKING LIGHT (+) INPUT - WHITE

STARTER (+) INPUT - BLACK/WHITE

*E-BRAKE STATUS (-) OUTPUT - GREEN

*TACH (AC) OUTPUT - PURPLE/WHITE

ONLY WHEN RAP

SHUTDOWN IS REQUIRED

REARM (-) OUTPUT

TACH (AC) INPUT

E-BRAKE STATUS (-) INPUT

STARTER (+) OUTPUT

PARKING LIGHT (+) OUTPUT

RIGHT SLIDING DOOR (-) OUTPUT

LEFT SLIDING DOOR (-) OUTPUT

DISARM ONLY (-) OUTPUT

TRUNK (-) OUTPUT

UNLOCK (-) OUTPUT

LOCK (-) OUTPUT

GROUND WHEN RUNNING (-) OUTPUT

LOCK (-) OUTPUT

DATA MODE

E D

REMOTE STARTER

<- REQUIRED <- REQUIRED <- REQUIRED <- REQUIRED <- REQUIRED <- REQUIRED <- REQUIRED <- REQUIRED <- REQUIRED <- REQUIRED <- REQUIRED <- REQUIRED

OPTIONAL -> OPTIONAL -> OPTIONAL ->

IGNITION OUTPUT - PINK

GROUND INPUT - BLACK

12V (+) INPUT - RED/WHITE

BRAKE INPUT - ORANGE

DO NOT USE THE RED/WHITE

WIRE IF YOU ARE PLANNING

TO POWER THE VEHICLE

POSITIVE PARKLIGHTS WIRE.

PARKING LIGHT (+) OUTPUT

TRUNK STATUS (-) INPUT

TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT

DOOR STATUS (-) INPUT

A

YELLOW/BLACK - DOOR STATUS (-) OUTPUT*

YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT*

YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW - MULTIPLEX PARKING LIGHT OUTPUT

YELLOW - MULTIPLEX PARKING LIGHT OUTPUT

B

G

USE THIS OUTPUT ONLY ON VEHICLES EQUIPPED WITH

MUX PARKING LIGHT CONTROL

VEHICLE PARKING LIGHT MUX WIRE

WARNING

F

THE BRAKE STATUS WIRE IS FUNCTIONAL

ONLY WHEN THE IGNITION IS POWERED.

HARDWARE IS VERSION

DIRECTLY TO THE VEHICLE

SOLD SEPARATELY

FLCHH (NEW)FLCHH (OLD)

ASSEMBLY ASSEMBLY

F E D

E

D

A B

OR

C

G

F

C

IF YOUR MODULE

1.23 OR NEWER YOU CAN ELIMINATE THE

RELAY AND CONNECT

THE YELLOW WIRE

A B C

87

87A

85

86

30

SOLD SEPARATELY

VEHICLE HARNESSVEHICLE HARNESS

G

XX-XX PAGE X-X

ADS-AL(DL)-CH4 T2 PAGE X-X

INSTALL GUIDE

ALL IN ONE

Chrysler/DoDge/Jeep

Page 4 of 9 FLC-AL(DL)-CH4 20120328

Doc. No.: ##9016##

TYPE 2 - WIRE CROSS REFERENCE CHART

CAN HIGH CAN LOW LEFT FRONT DOOR PARKING LIGHT IGNITION

MAKE

300 08-11 5 White/Black A 6 White/LtBlue A Violet B White/Brown MUX E 3 Pink/White 300 Limited 08-11 5 White/Black A 6 White/LtBlue A Violet B White/Brown MUX E 3 Pink/White 300c 08-11 5 White/Black A 6 White/LtBlue A Violet B White/Brown MUX E 3 Pink/White 300c SRT8 08-11 5 White/Black A 6 White/LtBlue A Violet B White/Brown MUX E 3 Pink/White

CHRYSLER

Town & Country 08-10 5 White/LtBlue A 6 White/Brown A Violet C White/Brown MUX F 3 Pink/White Town & Country 11-12 5 White/LtBlue A 6 White/Brown A Violet C White/Green MUX F 3 Pink/White Caravan 08-10 5 White/LtBlue A 6 White/Brown A Violet C White/Brown MUX F 3 Pink/White Challenger SXT 08-11 5 White/Black A 6 White/LtBlue A Violet C White/Brown MUX F 3 Pink/White Challenger R/T 08-11 5 White/Black A 6 White/LtBlue A Violet C White/Brown MUX F 3 Pink/White Challenger SRT8 08-11 5 White/Black A 6 White/LtBlue A Violet C White/Brown MUX F 3 Pink/White Charger SE 08-11 5 White/Black A 6 White/LtBlue A Violet B White/Brown MUX E 3 Pink/White Charger R/T 08-11 5 White/Black A 6 White/LtBlue A Violet B White/Brown MUX E 3 Pink/White Charger SRT8 08-11 5 White/Black A 6 White/LtBlue A Violet B White/Brown MUX E 3 Pink/White Durango 11 5 White/LtGreen A 6 White/LtBlue A Violet/Gray C White MUX F 3 Pink/White

DODGE

Grand Caravan 08-10 5 White/LtBlue A 6 White/Brown A Violet C White/Brown MUX F 3 Pink/White Grand Caravan 11-12 5 White/LtBlue A 6 White/Brown A Violet C White/Green MUX F 3 Pink/White Journey 09-10 5 White/LtBlue A 6 White/Brown A Violet C White/Violet (+) H 3 Pink/White Magnum 08 5 White/Black A 6 White/LtBlue A Violet B White/Brown MUX F 3 Pink/White RAM 1500 09-12 5 White/LtGreen A 6 White/LtBlue A Violet/Gray C White MUX F 3 Pink/White RAM 2500 10-12 5 White/LtGreen A 6 White/LtBlue A Violet/Gray C White MUX F 3 Pink/White RAM 3500 10-12 5 White/LtGreen A 6 White/LtBlue A Violet/Gray C White MUX F 3 Pink/White Commander 08-10 5 White/LtGreen A 6 White/LtBlue A Violet D N/A (-) G 3 Pink/White

JEEP

Grand Cherokee 08-11 5 White/LtGreen A 6 White/LtBlue A Violet D N/A (-) G 3 Pink/White C/V 10 5 White/LtBlue A 6 White/Brown A Violet C White/Brown MUX F 3 Pink/White C/V 11-12 5 White/LtBlue A 6 White/Brown A Violet C 1500 10-12 5 White/LtGreen A 6 White/LtBlue A Violet/Gray C White MUX F 3 Pink/White

RAM

2500 10-12 5 White/LtGreen A 6 White/LtBlue A Violet/Gray C White MUX F 3 Pink/White 3500 10-12 5 White/LtGreen A 6 White/LtBlue A Violet/Gray C White MUX F 3 Pink/White

MODEL

YEAR

POSITION

WIRE

COLOR

LOCATION

POSITION

WIRE

COLOR

LOCATION

WIRE

COLOR

LOCATION

White/Green MUX F 3 Pink/White

WIRE

COLOR

POLARITY

LOCATION

POSITION

WIRE

COLOR

Routan 09-12 5 White/LtBlue A 6 White/Brown A Violet C White/Brown MUX F 3 Pink/White

VOLKSWAGEN

*LEGEND - COMPONENT LOCATOR

A At 12-pin node B Black connector at drivers kick panel C At drivers kick panel D Left door E At switch or drivers kick panel F At switch G At pin 1 of relay 7 in IPM H At passengers kick panel

INSTALL GUIDE

ALL IN ONE

Chrysler/DoDge/Jeep

Page 5 of 9 FLC-AL(DL)-CH4 20120328

Doc. No.: ##9016##

TYPE 2 - WIRING DIAGRAM

VEHICLE PARKING LIGHT MUX WIRE

IF YOUR MODULE

HARDWARE IS VERSION

1.23 OR NEWER YOU CAN ELIMINATE THE

RELAY AND CONNECT

THE YELLOW WIRE

DIRECTLY TO THE VEHICLE

5 AMPS

WARNING

87

87A

85

86

30

1N4001

DIODE

E-BRAKE STATUS (-) INPUT

STARTER (+) OUTPUT

PARKING LIGHT (+) OUTPUT

RIGHT SLIDING DOOR (-) OUTPUT

LEFT SLIDING DOOR (-) OUTPUT

GROUND WHEN RUNNING (-) OUTPUT

LEGEND

N/A

NOT REQUIRED IN DATA MODE (1-WAY) NOT REQUIRED IN DATA MODE (2-WAY)

USE DATA MODE

OR HARDWIRE MODE

DATA MODE

GWR (-) INPUT - BLUE/WHITE

LOCK/ARM (-) INPUT - GREEN/BLACK

UNLOCK/DISARM (-) INPUT - BLUE/BLACK

LEFT SLIDING DOOR (-) INPUT - PURPLE/YELLOWLEFT SLIDING DOOR (-) INPUT - PURPLE/YELLOW

RIGHT SLIDING DOOR (-) INPUT - PURPLE/BLACK

TRUNK (-) INPUT - RED/WHITE

DISARM ONLY (-) INPUT - BROWN

PARKING LIGHT (+) INPUT - WHITE

STARTER (+) INPUT - BLACK/WHITESTARTER (+) INPUT - BLACK/WHITE

*E-BRAKE STATUS (-) OUTPUT - GREEN

*TACH (AC) OUTPUT - PURPLE/WHITE

(NC) WHITE

GROUND - BLACK

12V (+) - RED

DISARM (+) OUTPUT

TRUNK (-) OUTPUT

UNLOCK (-) OUTPUT

TACH (AC) INPUT

LOCK (-) OUTPUT

12V (+)

GROUND (-)

DATA MODE

ONLY WHEN RAP

SHUTDOWN IS REQUIRED

REMOTE STARTER

<- REQUIRED <- REQUIRED <- REQUIRED <- REQUIRED <- REQUIRED <- REQUIRED <- REQUIRED <- REQUIRED <- REQUIRED <- REQUIRED <- REQUIRED <- REQUIRED <- REQUIRED

REQUIRED -> REQUIRED -> REQUIRED -> REQUIRED -> OPTIONAL -> OPTIONAL ->

WARNING USE THIS OUTPUT ONLY ON VEHICLES EQUIPPED WITH

MUX PARKING LIGHT CONTROL

VEHICLE (-) DRIVER DOOR PIN

REARM (-) OUTPUTREARM (-) OUTPUT

PARKING LIGHT (+) OUTPUT

PARKING LIGHT (+) OUTPUT 1ST IGNITION (+) INPUT

1ST IGNITION (+) INPUT

BRAKE (+) INPUT

TRUNK STATUS (-) INPUT

DOOR STATUS (-) INPUT

REMOTE STARTER START OUTPUT

MUST BE EXTENDED TO ITS MAXIMUM

WHEN USING TACHLESS MODE

(CRANK TIME: AT LEAST 2.5 SECONDS)

OR USE TACH CONNECTION INSTEAD

WHITE/BLACK - IGNITION (+) VEHICLE SIDEWHITE/BLACK - IGNITION (+) VEHICLE SIDE

WHITE/RED - IGNITION (+) CONNECTOR SIDE

WHITE

YELLOW/BLACK - DOOR STATUS (-) OUTPUT*

YELLOW/RED - TRUNK STATUS (-) OUTPUT*

YELLOW - MULTIPLEX PARKING LIGHT OUTPUT

BROWN/RED - CANH

BROWN/YELLOW - CANLBROWN/YELLOW - CANL

ORANGE/BLACK (NC)

ORANGE/BLACK (NC) ORANGE/WHITE (NC)

ORANGE/WHITE (NC)

ORANGE - BRAKE STATUS (+) OUTPUT*

PINK/BLACK (NC)

PINK - IGNITION (+) INPUT VEHICLE SIDEPINK - IGNITION (+) INPUT VEHICLE SIDE

BLUE/RED (NC)

BLUE/RED (NC) BLUE/YELLOW (NC)

BLUE/YELLOW (NC) GREEN/RED (NC)

GREEN/RED (NC) GREEN/YELLOW (NC)

GREEN/YELLOW (NC)

GRAY/RED - IGNITION (+) INPUT FROM KEY

GRAY/YELLOW (NC)

FOR SECURE TAKE OVER, CONNECT THE

BRAKE STATUS WIRE TO THE REMOTE STARTER.

DO NOT CONNECT TO THE VEHICLE BRAKE WIRE,

IT VOIDS THE SECURE TAKE OVER FEATURE.

THE BRAKE STATUS WIRE IS FUNCTIONAL

ONLY WHEN THE IGNITION IS POWERED.

WARNING

IGNITION - PINK/WHITE

1 2 3 4 5 6

7 8 9 10 11 12

5 6

3

CANH

CANL

XX-XX PAGE X-XADS-AL(DL)-CH4 1-2 PAGE X-X

ADS-AL(DL)-CH4 90

UNLOCK

INSTALL GUIDE

ALL IN ONE

Chrysler/DoDge/Jeep

Page 6 of 9 FLC-AL(DL)-CH4 20120328

INSTALLATION MODE SELECTION

Press and release

1

LED ﬂ ashes (1X) once = DATA MODE LED ﬂ ashes (2X) twice = STANDARD HARDWIRE MODE

1

programming button to select installation mode.

MODULE PROGRAMMING PROCEDURE

Close driver door.

Re-open driver door to wake up data bus.

Insert key into ignition.

2

6

7

After registration, follow Factory Reset Procedure to change installation mode and restart this procedure.

!

OFF

2

8

Doc. No.: ##9016##

Press and hold programming button until LED turns solid GREEN to register selection.

Turn key to OFF position.

Remove key.

Press UNLOCK on the OEM remote.

3

4

5

ON

Turn key to ON position.

LED will turn solid RED.

Within 5 seconds, LED will ﬂ ash GREEN rapidly.

9

10

If vehicle is not equipped with OEM remote, press module programming button.

Wait, LED will turn solid GREEN for 2 seconds.

Module Programming Procedure completed.

XX-XX PAGE X-XADS-AL(DL)-CH4 2-2 PAGE X-X

UNLOCK

INSTALL GUIDE

ALL IN ONE

Chrysler/DoDge/Jeep

Page 7 of 9 FLC-AL(DL)-CH4 20120328

MODULE PROGRAMMING PROCEDURE - PUSH TO START

Press and release

Close driver door.

1

LED ﬂ ashes (1X) once = DATA MODE LED ﬂ ashes (2X) twice = STANDARD HARDWIRE MODE

2

x2



programming button to select installation mode.

Re-open driver door to wake up data bus.

DO NOT PRESS BRAKE PEDAL

Push start button twice [2x] to ON position.

LED will turn solid RED.

3

Within 5 seconds, LED will ﬂ ash

4

GREEN rapidly.

INSTALLATION MODE SELECTION

2

5



6

7

8

After registration, follow Factory Reset Procedure to change installation mode and restart this procedure.

!

x1

Doc. No.: ##9016##

Press and hold

DO NOT PRESS BRAKE PEDAL

programming button until LED turns solid GREEN

Push start button once [1x] to

to register selection.

OFF position.

Press UNLOCK on the OEM remote.

If vehicle is not equipped with OEM remote, press module programming button.

Wait, LED will turn solid GREEN for 2 seconds.

Module Programming Procedure completed.

XX-XX PAGE X-XCLASSIC PAGE 1-1

INSTALL GUIDE

ALL IN ONE

Chrysler/DoDge/Jeep

Page 8 of 9 FLC-AL(DL)-CH4 20120328

Doc. No.: ##9016##

IDENTIFY VEHICLE YEAR

Locate the Vehicle Identiﬁ cation

1

Number (VIN) and identify the 10th character.

4 Y 1 N53 A 5 T A L 8 D 5 R 0 X



2

L > 1990 S > 1995 Y > 2000 5 > 2005 A > 2010

M > 1991 T > 1996 1 > 2001 6 > 2006 B > 2011

N > 1992 V > 1997 2 > 2002 7 > 2007 C > 2012

P > 1993 W > 1998 3 > 2003 8 > 2008 D > 2013

R > 1994 X > 1999 4 > 2004 9 > 2009 E > 2014

Match the VIN’s 10th character to its corresponding year.

MODULE DIAGNOSTICS

LED STATUS

Flashing RED

Solid RED Waiting for more vehicle information Incorrectly programmed

Flashing GREEN

DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF

Missing/wrong information from ﬁ rmware or vehicle

Additional steps required to complete programming

Incorrectly programmed Incorrectly programmed or connected

Correctly programmed and operational

DIAGNOSTICS

Not programmed waiting for more vehicle information

False ground when running status from remote starter

Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress

OFF No activity or already programmed

Invalid ground when running status from remote starter

At rest and ready for a remote start sequence

FACTORY RESET PROCEDURE

1

2

3

4









DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector.

DISCONNECT black 4-PIN standard or optional data connector.

PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector.

When LED ﬂ ashes red,

RELEASE programming button.

5

6

7





Failure to follow procedure may result with a DTC or a CHECK ENGINE error message.

!

LED will turn solid red for 2 seconds.

RESET COMPLETED.

RECONNECT all connectors.

Repeat programming procedure.

ADS-AL(DL)-CH4 1-2 PAGE X-X

INSTALL GUIDE

ALL IN ONE

Chrysler/DoDge/Jeep

Page 9 of 9 FLC-AL(DL)-CH4 20120328

WARNING: READ BEFORE REMOTE STARTING THE VEHICLE

IMPORTANT

I All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction.

TAKE OVER PROCEDURE - TO THE VEHICLE OWNER

NOTE

I All vehicle doors must be closed and locked prior to remote

start sequence.



1

TIME RESTRICTIN COMING UP !

Press UNLOCK on after-market remote.

3

4

ON

5

Doc. No.: ##9016##

Insert key into ignition.

Turn key to ON position.

Wait 2 seconds for key validation.

Press and release BRAKE pedal.

2

TAKE OVER PROCEDURE - PUSH TO START - TO THE VEHICLE OWNER

NOTE

I All vehicle doors must be closed and locked prior to remote

start sequence.



TIME RESTRICTIN COMING UP !

1

2

TIME RESTRICTIN

Within 45 SECONDS from previous step:

Open vehicle door. Enter vehicle.

Press UNLOCK on after-market remote.

TIME RESTRICTIN

Within 45 SECONDS from previous step:

Open vehicle door. Enter vehicle.

6

3

4

5

Take over procedure completed.

Failure to follow procedure within time restriction will result in vehicle engine shutdown.

!

DO NOT PRESS BRAKE PEDAL

x2



Failure to follow procedure within time restriction will result in vehicle engine shutdown.

!

Push start button twice [2x] to ON position.

Wait 2 seconds for key validation.

Press and release BRAKE pedal.

Take over procedure completed.