Flash butrym F7000563a User Manual

USER MANUAL

LED MOVING HEAD BEAM 7x15W RGBW

4in1 OSRAM 5°/25°

F7000563a

LED MOVING HEAD BEAM 7x15W RGBW 4in1 OSRAM 5°/25° F7000563a

www.flash-butrym.pl

1

Table of Contents

1 Introduction ...................................................................................................................................................... 2

2 Safety information ........................................................................................................................................... 2

3 Product information ........................................................................................................................................ 3

3.1 Features ....................................................................................................................................................... 3

3.2 Specification ................................................................................................................................................ 3

4 Installation ........................................................................................................................................................ 4

5 Connections ...................................................................................................................................................... 6

5.1 Connecting DMX signal............................................................................................................................. 6

5.2 Voltage specification .................................................................................................................................. 7

5.3 Connecting power supply ........................................................................................................................ 7

6 Maintenance and Cleaning ............................................................................................................................. 7

7 Operation manual ............................................................................................................................................ 8

7.1 Control panel .............................................................................................................................................. 8

7.2 Menu ............................................................................................................................................................ 8

7.3 DMX channel list ........................................................................................................................................ 9

www.flash-butrym.pl

2

1 INTRODUCTION

Thank you for purchasing this LED MOVING HEAD. For safety reasons and to ensure the trouble-free
operation, carefully read the instructions before installing the device. Please install and operate the fixture
with following instructions.

2 SAFETY INFORMATION

This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe
operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written
in this user manual.

IMPORTANT! Damages caused by the disregard of this user manual are not subject to warranty. The dealer

will not accept liability for any resulting defects or problems.

1. Installation should be done by qualified personnel in order to minimize the risk of accidental

electric shock

2. Disconnect the power supply before installation.

3. Before connecting the unit to the mains, make sure it is not damaged mechanically. If you notice

any signs of damage you should contact your dealer immediately. Do not connect the device to
the mains.

4. Do not use the device in high humidity conditions and at temperatures above 45° C

5. The device must be installed on stable structures.

6. If the device has been exposed to temperature changes due to environmental changes, do not

switch it on immediately. The arising condensation could damage the device.

7. Leave the device switched off until it has reached room temperature.

8. This device falls under protection-class I. Therefore it is essential that the device be earthed.

9. The device shall only be used with rate voltage and frequency.

10. Make sure that the available voltage is not higher than stated at the end of this manual.

11. Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case,

replacement of the cable must be done by an authorized dealer.

12. Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle

the power cord by the plug. Never pull out the plug by tugging the power cord.

13. During initial start-up some smoke or smell may arise. This is a normal process and does not

necessarily mean that the device is defective, it should decrease gradually.

14. Please don‘t project the beam onto combustible substances.

15. Fixtures cannot be installed on combustible substances, keep more than 50cm distance with wall

for smooth air flow, so there should be no shelter for fans and ventilation for heat radiation.

16. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced

by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.

LED MOVING HEAD BEAM 7x15W RGBW 4in1 OSRAM 5°/25° F7000563a

www.flash-butrym.pl

3

3 PRODUCT INFORMATION

This Fixture is made of a new type of high temperature strength of engineering plastics and cast aluminum
casing with nice outlook. The fixture is designed and manufactured strictly following CE standards,
complying with international standard DMX512 protocol. It’s available independently controlled and
Iinkable with each other for operation. And it is applicable for large-scale live performances, theater, studio,
nightclubs and discos.

4-lN-1 LEDs (RGBW) which features high brightness and stability. Please carefully unpack it when you
receive the fixture and check whether it is damaged during the transportation. And please check whether
the following items are included inside the box: Moving Head, Power Cable, User Manual

3.1 Features

 7PCS OSRAM 15W 4-IN-1 LEDs (R,G,B,W)
 60,000 hours life span for LEDs and low power consumption
 Intelligent temperature sensor for LEDs (overheat protection)
 High efficiency 8° optic lens
 Color range with 16.7 millions additive RGBW colors
 High light output as 860LUX@ 7M at full
 0-100% smooth linear dimmer with flicker free
 20t/s strobe effect with variable speed
 Pre-programmed random strobe and pulse effects
 17/40 CH DMX channels
 Built-in programs with macro effects
 DMX512, master-slave and sound activated controllable or auto operation
 High definition TFT LCD display
 Quiet, smooth and fast PAN/TILT movement
 Low noise and efficient FAN cooling system
 540° PAN and 250° TILT movement
 Scan position memory, auto reposition after unexpected movement
 Compact size with only 4,9KG body and 31mm in height
 powerCON connector
 45°C max ambient temperature
 IP20 protection rating
 3-Pin XLR DMX input/output

3.2 Specification

 Input Voltage: AC90-260V 50/60Hz
 LED Quantities: 7PCS of 15W OSRAM 4-IN-1 LEDs (R, G, B, W)
 Control Signal: DMX512, master-slave and sound activated or auto operation
 Control Channel: 17/40 DMX channels
 Power Consumption: 100W
 Dimensions: 152mm(L) 265mm(W) 310mm(H)
 Packing Dimensions:260 mm(L) 320mm(W) 335mm(H)
 Net Weight: 4,9kg
 Gross Weight: 7,5kg