www.flash-butrym.pl Page 1
LED MOVING HEAD ZOOM 144W WASH
4in1 RGBW
User Manual
Table of contents
1. Preface 2
1.1 Packing list 2
1.2 Unpacking instructions 2
1.3 AC Power 2
1.4 Safety instructions 2
2. Introduction 3
2.1 Features 3
2.2 DMX channel 3
3. Setup 3
3.1 Fuse replacement 4
3.2 Fixture linking 4
Data cabling 4
DMX data cable 4
3.3 3-Pin to 5-Pin conversion chart 4
3.4 Setting up a DMX serial data link 4
3.5 Master/Slave fixture linking 5
3.6 orientation 5
4. Operating instructions 5
4.1 Navigating the control panel 5
4.2 Menu map 6
4.3 User configurations 6
Setup single-desk light`s autocephaly moving mode(self-motion move) 6
Setup single-desk light`s autocephaly moving mode(sound control) 6
Master/slave mode(master sound,master auto) 6
To set the pan to reverse or non-inverting 6
To set the tilt to reverse or non-inverting 7
To set the LED readout to inverting or non-inverting 7
resume reverse windows default 7
DMX mode 7
4.4 DMX channel values 7
5. Technical specifications 8
Pleese read these instructions cy, it includes important information about the
installation, usage and maintenance of this product.
Warning! Verify that the voltage select switch on your unit matches the line
voltage applied. Damage to your fixture may result if the line voltage applied
does not match the voltage indicated on the voltage selector switch. All fixtures
must be connected to circuits with a suitable Earth ground.
1. Preface
1.1 Packing list
Product name
quantity
Mini Moving Head Light
1 pcs
Unser Manual
1pcs
1.2 Unpacking instructions
On receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are presented, and have been received in a good condition. Notify the
shipper immediately and retain packing material for inspection if any parts appear
damaged from shipping or the carton itself shows, sign of mishandling. Save the
carton and all packing materials. In the event that a fixture must be returned to the
factory , it is important that the fixture be returned in the original factory box and
packing.
1.3 AC Power
To determin the power requirements for a particular fixture, see the label affixed to
the back plate of the fixture or refer to the fixtures specifications chart. A fixture listed
current rating is its average current draw under normal conditions. All fixtures must
be directly powered off a switched circuit and cannot be run off a rheostat(variable
resisto) or dimmer circuit, even if the rheostat or dimmer source voltage matches the
fixtures requirement. Check the fixture or device carefully to make sure that if a
voltage selection switch exists that it sets to the correct line voltage you will use.
1.4 Safety instructions
Please keep this user guide for future consultation. If you sell the unit to another user,
be sure that they also receive this instruction booklet.
Always make sure that you are connecting to the proper voltage, and that the line
voltage you are connection to is not higher than that stated on the decal or rear panel
of the fixture.
This product is intended for indoor use only ! To prevent risk of fire or shock, do not
expose fixture to rain or moisture.
Make sure that there are no flammable materials close to the unit while operation.
The unit must be installed in a location with adequate ventilation, at least 20in(51cm)
from adjacent surfaces. Be sure that no ventilation slots are blocked.
Always disconnect from power source before servicing or replacing fuse and be sure
to be replaced with same fuse ，size and type.
Secure fixture to fastening device using a safety chain. Never carry the fixture solely
by its head. Use its carrying handles.
Disconnect the power cord before replacing a fuse and always replace with the
same type fuse.
Maximum ambient temperature (Ta) is 104℉(40℃ ). Do not operate fixture at
temperature higher than this.
In the event of a serious operating problem, stop using the unit immediately. Never try
to repair the unit by yourself. Repairs carried out by unskilled people will lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center. Always use the same type spare parts.
Don’t connect the device to a dimmer device.
Make sure the power cord never crimped or damaged.
Never disconnect the power cord by pulling the cord.
Avoid directing eye exposure to the light source while it is on.
2. Introduction
2.1 Features
12 channel DMX-512 .
Pan :630°/tilt:270°.
Variable electronic strobe.
Variable electronic dimmer(0-100%).
LED display menu with invert.
Reset to factory settings option.
Pan/tilt invert option.
Fan cooled.
2.2 DMX Channel
Channel
Function
1
Pan
2
Tilt
3
Pan/Tilt Speed
4
Red
5
Green
6
Blue
7
White
8
Mix color
9
Strobe and Reset
10
Dimmer
11
ZOOM
12
Pan Fine
13
Tilt Fine
3. Setup
3.1 Fuse replacement
With a flat head screwdriver wedge the fuse hold out of its housing. Remove the
damaged fuse from its holder and replace with exact same type fuse. Insert the fuse
holder back in its place and reconnect power.
3.2 Fixture linking
You will need a serial data link to run light show of one or more fixtures using a
DMX-512 controller or to run synchronized on two or more fixtures set to a
master/slave operating mode. The combined number of channels required by all the
fixtures on a serial data link determines the number of fixtures the data link can
support.
Maximum recommended serial data link distance:500 meters(1640ft).
Maximum recommended number of fixtures on a serial data link:32 fixtures.
Data cabling
To link fixtures together you must obtain data cables. If you choose to create your
own cable please use data-grade cables that can carry a high quality signal and are
less prone to electromagnetic interference.
DMX data cable
Use a belden 9841 or equivalent cable which meets the specifications for EIA RS-485
applications. Standard microphone cables cannot transmit DMX data reliably over
long distances. The cable will have the following character:
2-conductor twisted pair plus a shield.
maximum capacitance between conductors-30 pF/ft.
maximum capacitance between conductor and shield -55 pF/ft.
maximum resistance of 20 ohms/1000ft.
nominal impedance 100~140 ohms.
3.3 3-Pin to 5-Pin conversion chart
Note! If you use a controller with a 5 pin DMX output connector. you will need to use
a 5pin to 3 pin adapter
CHAUVET Model No:DMX5M. orDMX 5F
The chart below details a proper cable conversion:
3.4 Setting up a DMX serial data link
At first, link the first light and DMX control through XLR-connection signal cable
then devolute the light in series ,as follows:
3.5 Master/Slave fixture linking
1.Connect the (male) 3 pin connector side of the DMX cable to the output
(female)3pin connector of the first fixture.
2.Connect the end of the cable coming from the first fixture which will have a
(female)3 pin connector to the input connector of the next fixture consisting of a (male)
3 pin connector. Then, proceed to connect from the output as stated above to the
input of the following fixture and so on.
3.6 orientation
This fixture may be mounted in any position provided there is adequate room for
ventilation.
4. Operating instructions
4.1 Navigating the control panel
Access control panel functions using the four panel buttons located directly under the
LCD Display.
. When a menu function is selected, the display will show immediately the first available
option for the selected menu function. To select a menu item, press<ENTER>.
Press the <MENU> button repeatedly until you reach the desired menu function. Use
the <UP> and <DOWN> buttons to navigate the menu options. Press the <ENTER>
button to select the menu function currently displayed, or to enable a menu option. To
return to the previous option or menu without changing the value, press the <MENU>
button.
No alteratived worth that return re-option or menu , press(MENU)button
4.2 Menu map
RPON (address code setting from A001-------A512)
AU01(auto-moving speediness)
AU02(slow speed auto-moving)
SN01(Sound control for color changing)
SN02( Sound control for strobe)
RPOF(Set pan to forward-rotating)
RPON(Set pan circumrotate reverse)
RTOF(Set tilt to forward-rotating)
RTON(Set tilt circumrotate reverse)
RDOF(set the LED readout to non-inverting)
RDON(Set the LED readout to inverting)
DFON (Default output setting)
Note：output default setting address code is A001, pan is positive circumrotate、tilt
is positive circumrotate、LED positively reveal.
4.3 User configurations
Setup single-desk light`s autocephaly moving mode(auto-running)
.Press the MENU until it shows AU01
Button
Function
<MENU>
Used to access the menu or return to a previous
menu option.
<DOWN>
Scrolls through menu options in descending
order.
<UP>
Scrolls through menu options in ascending order.
<ENTER>
Used to select and store the current menu or
option within a menu.
.Use the UP/DOWN buttons to set to AU01 or AU02 ,Press ENTER to confirm.
Setup single-desk light`s autocephaly moving mode(sound control)
.Press the MENU button until it shows SNOF .
.Use the UP/DOWN buttons to set to SNOF,press ENTER to confirm.
Master/slave mode(auto-running、sound control)
.This mode will allow you to link up 32 units together without a controller.
.Use standard DMX cables to daisy chain your units together via the DMX connector
on the rear of the units.Proper performance it may be necessary to use a terminator
at the last fixture. For more information about terminators..
Set the desired master-mode- “Automatic program mode” or”sound controlled
mode”, for the master-device, send the DMX address 1 for all slave-devices. Please
refer to the instruction under control board.
To set the pan to reverse
.Press the MENU until it shows RPOF.
.Use the UP/DOWN buttons show RPON, press ENTER to confirm.
To set the tilt to reverse
.Press the MENU until it shows RTOF
.Use the UP/DOWN buttons show RTON, press ENTER to confirm.
To set the LED readout to 180°,rotating
.Press the MENU until it shows RDOF.
.Use the UP/DOWN buttons show RDON, press ENTER to confirm.
Resume reverse Windows default
.Press the MENU until it shows DFON.
.press ENTER to confirm。
DMX mode
This mode allows the unit to be controlled by any universal DMX controller.
The default mode for the fixture is DMX, as follows
4.4 DMX channel values
Channel
Value
Function
1
0-255
Pan
Pan movement
2
Tilt
0-255
Tilt movement
3
0-255
Pan/Tilt Speed
Pan/Tilt Speed
4
0-255
Red
0-100% Red
5
0-255
Green
0-100% Green
6
0-255
Blue
0-100% Blue
7
0-255
Amber
0-100% Amber
8
0-2
3-41
42-83
84-125
126-167
168-209
210-251
252-255
Mixed Color
No function
Macro 1
Macro 2
Macro 3
Macro 4
Macro 5
Macro 6
No function
9
0-10
11-20
21-30
31-200
201-250
251-255
Strobe and Reset
LED off
LED on
Reset
Strobe-effect with increasing speed
Random strobe-effect with increasing spped
LED on
10
0-255
Dimmer
0-100% dimme
11
0-255
zoom
12
0-255
Pan Fine
Pan fine
13
0-255
Tilt Fine
Tilt fine
5. Technic data
Voltage
230V 50Hz
Fuse
5A,Ф5×20mm,
Lamp resource
12pcs 12w LED
Pan
630°,16bit fine
Tilt
270°,16bit fine
Tiptop environment temperature
104°F(40°C)
Date input/output
3pin XLR-connection、anlde socket
Product size
260 ×260×350mm(L×W×H)
N.W
5.7kg
Packing size
645×360×405mm(L×W×H)(2pcs/package)
G.W (1pc)
6.6kg
Loading...