Flamerite Fires Tennyson Cast Instructions For Use Manual

Page 1 of 2

or

2.

Green and yellow:

EARTH

Blue:

NEUTRAL

Red:

LIVE

Flamerite Tennyson Cost Electric Stove

Installation of fire

Where a chimney is not blocked off completely it will cause the heater to cut out during use.

The overall dimensions of the cast are Height 955mm Width 955mm Depth 260mm (including fret & ash pan). The inset dimensions of the fire are
Height 590mm Width 475mm and Depth including recess of the cast arch 165mm. Please note if fitting flat to a wall the recess to the rear of the
arch will have to be taken into account. If fitting to a mantel with removable rebates this recess should not cause a problem. When fitting to a
Flamerite Fires Suite no inset is required as once the cast Arch is locked into place using all four tabs on the back of the suite the fireplace will fit
flat to any wall.

The fire must be positioned so that the plug socket is accessible once the fire has been installed. In the unlikely event of breakdown access may be
required to the rear so that the fire maybe serviced. The mains cable must therefore be long enough to allow this. If the removal of the plug is
absolutely necessary for installation, cut off in an area within 100mm only of the plug itself. Any further may affect your warranty. Where the fire

is being used in an existing chimney, it is important that the chimney is blocked off to prevent airflow problems. Where a chimney is not
blocked off sufficiently, it may cause the heater to cut out and the flame effect to stop or work inefficiently.

Electrical connections

Your appliance comes fitted with a plug that incorporates a 13A fuse. The replacement fuses must be 13A and ASTA approved. If the fuse cover is
lost the plug must not be used until a replacement cover, of the same colour, is obtained from an electrical retailer.
The appliance is fitted with a moulded plug if it is necessary cut off the plug, for any reason, it must be discarded immediately with the fuse
removed. Under no circumstances should any attempt be made to reuse the plug, do not insert into any 13A socket as this could cause a
hazard. If the mains cable is damaged it must be replaced by the manufacturer or an authorised technical service centre.

WARNING THIS APPLIANCE MUST BE EARTHED

IMPORTANT

The wires in the mains lead are coloured in accordance with the following code.

As the colours of the wires in the mains lead of this appliance may not correspond with the colour markings in your plug proceed as follows: -

The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E, or

coloured green or coloured green and yellow, or marked with the earth symbol

The wire which is coloured blue must be connected to the terminal in the plug which is marked with the letter N, or coloured

black.

The wire which is coloured brown must be connected to the terminal in the plug which is marked with the letter L, or coloured

red.

Fuel Effects

Once the fire has been installed in the correct position unpack the fuel effect from the accessory box. A picture of how to position the logs
can be seen below. If purchased with coals, these may be set out randomly although three of the larger coals should be placed on top of
the visible lights

Operating the fire

Controls
The controls can be found behind the ash pan cover.

The main on/off switch is marked with I/O and will need to be switched to I (standby) to operate the fire. In the O position (off) you will
be unable to operate the fire. The fire can be operated either by manual (keypad) or remote control of which a storage area when not in
use will also be visible.

1. To turn the fire on, simply press and release the FIRE ON button on the remote or manual keypad.

Page 2 of 2

2. To set the flame effect to your desired brightness press + or - buttons marked DIMMER1 1.

3. To set the fuel effect to your desired brightness press + or - buttons marked DIMMER2 or

4. To activate or deactivate the fuel flicker function press and release button Flicker. The flicker function will always deactivate once to
fire is turned off.