Flamerite Fires Luma Series, Ador, Luma 900, Luma 1200, Jaeger Series Installation, Precautions & Servicing

Carefully remove the fire from the packing checking neither the heater nor the power

Installation, Precautions & Servicing

Ador – Luma – Valentino - Jaeger

IMPORTANT

cable has been damaged during transport. Do not operate the fire if damaged. Please

bear in mind the weight of the fire before removal from the packaging and installation.

Consider if help is required. Always read this manual first before attempting to install

or use and keep in a safe place. Any alteration to the power cable should only be done

by a qualified electrician.

Your fire is guaranteed for one year from the date of purchase. In the unlikely event of

a breakdown you have access to our customer services team, simply call 01543 251122

during office hours, 9am – 5pm or e-mail on [e-mail] The accessories

are found in a box that is packed at the side of the fire.

This product is only suitable for well insulated spaces or occasional use

1 | Page

Important Safety Information and Warnings

Where a chimney is not blocked off completely, any draw will cause the heater to cut

• WARNING: In order to avoid overheating, do not cover the heater.

• For indoor use only.

• Do not use the fire in the vicinity of a bath, shower or swimming pool.

• Never use the fire to dry laundry.

• The heater must not be located immediately below a socket outlet.

• The use of an extension lead is not recommended.

• This appliance can be used by children aged from 8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made
by children without supervision.

• Children of less than 3 years should be kept away unless continuously supervised

• Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it

has been placed or installed in its intended normal operating position and they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved.

• Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or
perform user maintenance.

• Some parts of this product can become very hot and cause burns. Particular attention must be given
where children and vulnerable people are present

• Caution should be applied to ensure that children do not play with the fuel effects.

• As with any electrical appliance whilst the instructions aim to cover as many eventualities as possible,

caution and common sense should be applied when operating your appliance, particularly in the
vicinity of small children.

• CAUTION: The heater is fitted with an automatic cut out to prevent any damage due to overheating.
The element will continually and automatically cut out if the airflow is obstructed. Never cover the air
outlets. To reset, switch the fire off, disconnect from the mains supply, remove the cause of the
overheating. Allow to cool for a suitable period then switch the fire back on.

• CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut out, the
appliance must not be supplied through an external switching device, such as a timer, or connected to
a circuit regularly switched on and off by a utility.

out during use. Care should also be taken when fitting into a cavity wall in case of

damp or draft with external air vents fully sealed

2 | Page

Green and yellow:

EARTH

Blue:

NEUTRAL

Red:

LIVE

RECYCLING

for more details.

Electrical Connections

Insert the plug tightly into its IEC connector underneath the fire if not already done

Please recycle responsibly. Take your item to your local recycling
centre. You can easily locate your nearest centre on

the www.recyclenow.com website or check with your retailer for

details on either a collection service or a store take-back scheme (some
may apply charges). Councils may offer a household recycling
collection service for small electrical items; contact your local authority

Electrical connections. Your appliance comes fitted with a plug that incorporates a 13A fuse. The replacement

fuses must be 13A and ASTA approved. If the fuse cover is lost the plug must not be used until a replacement

cover, of the same colour, is obtained from an electrical retailer. The appliance is fitted with a moulded plug if

it is necessary cut off the plug, for any reason, it must be discarded immediately with the fuse removed.

Under no circumstances should any attempt be made to reuse the plug, do not insert into any 13A socket as

this could cause a hazard. If the mains cable is damaged it must be replaced by the manufacturer or an

authorised technical service centre.

WARNING THIS APPLIANCE MUST BE EARTHED

IMPORTANT

The wires in the mains lead are coloured in accordance with the following code.

As the colours of the wires in the mains lead of this appliance may not correspond with the colour markings in

your plug proceed as follows: -

• The wire which is coloured green and yellow must be connected to the terminal in the plug
which is marked with the letter E, or coloured green or coloured green and yellow, or marked
with the earth symbol

• The wire which is coloured blue must be connected to the terminal in the plug which is marked
with the letter N, or coloured black.

• The wire which is coloured brown must be connected to the terminal in the plug which is marked
with the letter L, or coloured red.

so. If the removal of the plug is absolutely necessary for installation, cut off in an

area within 100mm only of the plug itself. Any further will affect your warranty.

3 | Page

Jaeger

4x 60mm 2x 35mm 2x 16mm

4x 50mm 2x 35mm

Installation Instructions

Wall mounting

Suite Screws Rawl Plugs

Luma 3x 60mm 2x 35mm 2x 16mm 3x 50mm 2x 35mm

Ador 3x 60mm 2x 35mm 2x 16mm 3x 50mm 2x 35mm

The height at which you may wish to fix the fire in the wall is up to you, though we recommend anywhere

from 350-450mm from the floor to the bottom of the fire opening (not the bottom of the fire).

• The top MDF fixing rail should be fixed to the wall with the highest edge facing forward and the lowest
against the wall using the 3x 60m screws and 3x 50mm rawl plugs.

• The corresponding edge where the suite is to be hung on the top fixing rail can be found on the back,
at the top and across the suites centre.

• Once the top fixing rail is secured to the wall, lift and hook the suite onto it.

• The lower MDF rail should then be added to the underside of the suite. A channel in the underside will

be visible, the bottom rail will slot into this.

• With the suite in place, mark off the holes to be drilled, remove the suite and secure the lower rail to
the wall using the 2x 35mm screws and 2x 35mm rawl plugs. Refit the suite, lift and hook onto the
brackets.

• Finally fit the metal bracket to the lower rail and to the underside of the suite using the 16mm wood
screws. This will prevent the suite from being lifted off the fixing rails.

Valentino suite

• Your Valentino Suite is a freestanding and flat wall fix. Mirror clips are provided so you may secure it to
the wall

4 | Page

Log Effect

Your fuel effect may depend on what you have ordered to go with your suite. Pebbles & glass beads come as

standard. A small ember set can be part of this effect, all of which should be arranged randomly across the

fuel bed to suit (not pictured).

The log effect must be positioned according to the images below.

The Jaeger 1360 uses OmniGlide tilting glass, care are must be taken to ensure there is enough room between
the front of the logs and the glass channel at the front of the opening so the glass may tilt open freely into the

fire and trigger the micro switch.

Visit www.flameritefires.com/downloads if you require clearer downloadable images.

Small Cinder

5 | Page

Verada

Large Cinder

6 | Page

Jaeger

WARNING: The glass used is toughened, if mishandled it is designed to shatter. Extra care should be taken

during this procedure. Make sure the fire is turned off and the heater allowed to cool.

Glass Fitting & Removal

1360

Insert

• A Hold the glass panel in each bottom corner

• B Tilt the top of the glass into the fire

• C Place the bottom on the glass panel into the channel

• Adjust the glass panel for an even fit, side to side

Opening & Closing

To open and close the front glass panel, place your index finger on the handle as shown in the picture.

7 | Page

Remove

Maintenance

• A Hold the glass panel across the top either side of the heater

• B Pull up and outward of the channel toward you C. Do not rest on a hard surface

WARNING: Before any maintenance/cleaning is undertaken, always disconnect the fire from the mains

power supply.

Replacing Lamps

Dimmable 240V 6W 3000k E14 LED lamps

Allow a suitable time for the lamps to cool then remove the glass & fuel effect (see Installation). Remove the

two screws from either side of the fuel bed and lift out of place. Remove and replace the lamps, fuel bed, fuel

effect and glass. Please note that replacement Lamps are only covered from purchase by a 2-year warranty.

Replacements are available from Flamerite Fires Ltd

Cleaning

The fire can be cleaned with a soft cloth and nonabrasive glass cleaner.

8 | Page

Luma

1200

Jaeger

1020

Heat
output

Trouble Shooting

Information Requirements

• No power to the fire: Check the wall socket, plug, fuse and lamps.

• Heat turns off quickly after turn on: Set thermostat on app after turning heat on, not before.

• No illumination: Make sure fire is turned on. Check heater is working, if so check lamps.

• Heater blowing cold air: The safety cut out may have operated. Check for obstruction around the

heater. If continually a problem and fitted into a cavity wall or chimney breast check with installer the
inset opening has been 100% fully sealed from drawn air and draft.

• Noise when illuminated: Due to moving parts, the electric fire will make a noise.

• Noise from the heater when in use: The sound of rushing air is normal.

Information requirement for electric local space heaters

Model identifier (s) Ador Luma 900

Item Symbol Value Value Value Value Unit

Nominal heat output

Minimum heat output (indicative)

Maximum continuous heat output

Auxiliary electricity consumption

At nominal heat

At minimum heat

Instandby

Type of heat output/room temperature control

With distance control option

Room temperature control, with open window detection

Adaptive Start

With electronic room temperature control plus week timer Yes

Contact details: Flamerite Fires Ltd. Greenhough Road, Lichfield. Staffs.

WS137AU

Pnom 2 2 2 1.5 kW

Pmin 1 1 1 0.75 kW

Pmax,c 2 2 2 1.5 kW

elmax 35 43 43 48 W

elmin 35 43 43 48 W

elSB .5 .5 .5 .5 W

Yes

9 | Page

Model identifier (s)

Jaeger

600

Luma

1360

Item@

240v 50Hz

Heat
output

Circuit Diagram

Symbol Value Value Value Value Unit

Valentino

Jaeger1360

Nominal heat output

Minimum heat output (indicative)

Maximum continuous heat output

Auxiliary electricity consumption

At nominal heat

At minimum heat

Instandby

Type of heat output/room temperature control

With distance control option

Room temperature control, with open window detection

Adaptive Start

With electronic room temperature control plus week timer Yes

Contact details: Flamerite Fires Ltd. Greenhough Road, Lichfield. Staffs.

WS137AU

Pnom 1.5 2 1.5 1.5 kW

Pmin 0.75 1 0.75 0.75 kW

Pmax,c 1.5 2 1.5 1.5 kW

elmax 0.033 0.043 0.058 0.048 kW

elmin 0.033 0.043 0.058 0.048 kW

elSB 0.0005 0.0005 0.0005 0.0005 kW

Yes

10 | Page