Flamerite Fires Glazer 600, Glazer 900, Glazer 1000, Glazer 1500 Installation, Precautions, Servicing & User Instructions

Carefully remove the fire from the packing checking neither the heater nor the power

Installation, Precautions & Servicing

Glazer

600 900 1000 1500

IMPORTANT

cable has been damaged during transport. Do not operate the fire if damaged. Please

bear in mind the weight of the fire before removal from the packaging and installation.

Consider if help is required. Always read this manual first before attempting to install

or use and keep in a safe place. Any alteration to the power cable should only be done

by a qualified electrician.

Your fire is guaranteed for one year from the date of purchase. In the unlikely event of

a breakdown you have access to our customer services team, simply call 01543 251122

during office hours, 9am – 5pm or e-mail on [e-mail] The accessories

are found in a box that is packed at the side of the fire.

This product is only suitable for well insulated spaces or occasional use

1 | Page

Important Safety Information and Warnings

Where a chimney is not blocked off completely, any draw will cause the heater to cut

• For indoor use only.

• Do not use the fire in the vicinity of a bath, shower or swimming pool.

• Never use the fire to dry laundry.

• Never install the fire directly underneath a fixed main socket.

• Never cover the appliance.

• The use of an extension lead is not recommended.

• This appliance can be used by children aged from 8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance.

• Cleaning and user maintenance shall not be made by children without supervision.

• Children of less than 3 years should be kept away unless continuously supervised

• Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it

has been placed or installed in its intended normal operating position and they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved.

• Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or
perform user maintenance.

• Some parts of this product can become very hot and cause burns. Particular attention has to be given
where children and vulnerable people are present

• Caution should be applied to ensure that children do not play with the fuel effects.

• As with any electrical appliance whilst the instructions aim to cover as many eventualities as possible,

caution and common sense should be applied when operating your appliance, particularly in the
vicinity of small children.

• CAUTION: The heater is fitted with an automatic cut out to prevent any damage due to overheating.
The element will continually and automatically cut out if the airflow is obstructed. Never cover the air
outlets. To reset, switch the fire off, disconnect from the mains supply, remove the cause of the
overheating, where fitted check the OmniGlide micro switches. Allow to cool for a suitable period
then switch the fire back on.

• CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut out, the
appliance must not be supplied through an external switching device, such as a timer, or connected to
circuit regularly switched on and off by a utility.

out during use. Care should also be taken when fitting into a cavity wall in case of

damp or draft with external air vents fully sealed

2 | Page

Green and yellow:

EARTH

Blue:

NEUTRAL

Red:

LIVE

RECYCLING

Electrical Connections

Insert the plug tightly into its IEC connector underneath the fire if not already done

Please recycle responsibly. Take your item to your local recycling
centre. You can easily locate your nearest centre on

the www.recyclenow.com website or check with your retailer for

details on either a collection service or a store take-back scheme (some
may apply charges). Councils may offer a household recycling
collection service for small electrical items; contact your local authority

Electrical connections. Your appliance comes fitted with a plug that incorporates a 13A fuse. The replacement

fuses must be 13A and ASTA approved. If the fuse cover is lost the plug must not be used until a replacement

cover, of the same colour, is obtained from an electrical retailer. The appliance is fitted with a moulded plug if

it is necessary cut off the plug, for any reason, it must be discarded immediately with the fuse removed.

Under no circumstances should any attempt be made to reuse the plug, do not insert into any 13A socket as

this could cause a hazard. If the mains cable is damaged it must be replaced by the manufacturer or an

authorised technical service centre.

WARNING THIS APPLIANCE MUST BE EARTHED

IMPORTANT

The wires in the mains lead are coloured in accordance with the following code.

As the colours of the wires in the mains lead of this appliance may not correspond with the colour markings in

your plug proceed as follows: -

• The wire which is coloured green and yellow must be connected to the terminal in the plug
which is marked with the letter E, or coloured green or coloured green and yellow, or marked
with the earth symbol

• The wire which is coloured blue must be connected to the terminal in the plug which is marked
with the letter N, or coloured black.

• The wire which is coloured brown must be connected to the terminal in the plug which is marked
with the letter L, or coloured red.

so. If the removal of the plug is absolutely necessary for installation, cut off in an

area within 100mm only of the plug itself. Any further will affect your warranty.

3 | Page

Stud Wall

3x 60mm screws

Modular Chimney

3x M10 x 50mm Rawl plugs. 3x 60mm screws

Breast

2x 50mm screws & cover caps. 4x 13m screws.

Modular Wall

7x M10 x 50mm Rawl plugs. 7x 60mm screws. 2x M6 x 25mm bolts.

& Freestanding

2x M6 washers. 8x 13mm screws (4 fitted/4 packed)

Installation Instructions

DO NOT TWIST, FORCE OR SQUEEZE THE FIRE DURING THE INSTALLATION PROCESS.

Using in a chimney breast, fireplace or an internal studwork and plaster board wall.

The fire must be well supported in a structure when mounting above the floor. A wall support or lintel should

be fitted at the required height to ensure the appliance does not support the weight of the finished wall or

chimney breast. The height at which you may wish to fix the fire in or on the wall is up to you, we recommend

anywhere from 350-450mm from the floor to the bottom of the fire opening (not the bottom of the fire).

Secure into place using the fixings provided.

Situ Fixings

Modular suite, wall mounting & freestanding

The fire comes with two hanging rails top and bottom to fix the Glazer to the wall. Using the lower bracket
mark the holes, drill with a M10 bit and fit the rawl plugs. Using the 60mm screws, secure the bracket to the
wall.

Position the fire on top of the bottom bracket making sure the corner bolts fit through the slots either side
and can screw into the underside of the fire. With the top bracket attached to the fire, mark across its length
and into the slots above each hole on the back edge. Remove the top bracket and 13mm screws from the fire.
Using as a template mark the holes on the wall, drill and fit the rawl plugs using an M10 bit. Using the 60mm
screws fix the bracket to the wall.

4 | Page

Slide the fire into the channel created by the top and bottom brackets. Screw the top bracket back onto the
fire with the 13mm self-tappers and bolt each corner of the bottom bracket through the slots either side into
the fire using the M6 bolts and washer supplied. At this point you will be able to level the fire accordingly at
the base by loosening and tightening the bottom bolts.

If the fire is mounted to the wall, the base will slide on from the front between the flange running around the
opening and the pull-out tabs A. If using in a freestanding suite the fire should be pushed in from the back in
the same way, then the whole suite pushed up against the wall. In both cases make sure the power cable is
firmly pushed into the fire and does not foul the suite when up against the wall.

Using four of the 13mm screws secure the base to the fire along the side flange and fit the décor trim B. The
décor trim is the long black channel that provides a neat edge along the bottom of the fire opening, it is held
in place with magnets.

Fix the gloss black decorative panels either side of the opening to the fire C, also held in place with magnets.

5 | Page