Page 1
INSTALLATION MANUAL
Pro Series T-Top
Custom Fit Canvas Canopy Included
c
2020 Fishmaster All Rights Reserved 2640 Byington Solway Rd, Knoxville, TN 37931 877.777.8693 fishmaster.com
DES-183
REV 1.0
Page 2
Included Hardware Identification
4x
8x
8x
10x
Gather Additional Tools and Materials
Reversible Drill
16 x
16 x
Permanent Marker
Actual Size
12 x
18 x
4x
Parts List:
(5) Canopy Coupler
(4) Canopy Sections
(4) Leg Sections
(4) Upright Caps
(2) Standoffs
(2) Allen Keys
(2) Nylon Washers
(1) Canvas Cover
(1) Rope
TM
(1) 3M 5200 Adhesive Tube
(1) Marine Lubricant
45 Degree Chamfer Bit
3/16” Drill Bit
Screwdriver
Blue Painter’s Tape
Tape Measure
CAUTION: If you are unfamiliar with your boat’s construction,
please seek professional advice before installing the t-top.
!
For added assistance when installing the t-top, please consider
watching the installation video at: fishmaster.com
Or call us at 877-777-8693
As you plan to install the, Fishmaster Pro Series T-Top, keep
in mind that drilling into the console and deck of the boat is
needed in order to safely secure the t-top to the boat.
Level
Hammer
Center Punch
(16) 8” Cable Ties
Marine Grease for Bolts
*
Loctite 242 Blue
R
14” Long 3/8” Drill Bit
*Loctite 242 Blue can be applied to any bolt during assembly to ensure a locking fit.
R
Do you have questions? Call us @ 877.777.8693 Monday – Friday, 8am-5pm EST
c
2020 Fishmaster All Rights Reserved 2640 Byington Solway Rd, Knoxville, TN 37931 877.777.8693 fishmaster.com
2
DES-183
REV 1.0
Page 3
Step 1: Assemble Side Sections
Hardware Needed:
PRO TIP: Get the bolts
snug in place first, then come
back to tighten down fully
after each step.
Attach leg sections together with
1.
the hinge facing the bow of the boat.
Insert the M10x35 bolts to connect the
2.
top and lower sections.
Insert the nylon washer followed by the
3.
hinge bolt and lock nut into the hinge.
Step 2: Positioning The Assembled Legs
It is important to understand the placement of
1.
the legs will need to be square and even with the
opposite side of the console.
PRO TIP: It is recommended
to place the leg 1”-7” away from
the sides of the console.
Do you have questions? Call us @ 877.777.8693 Monday – Friday, 8am-5pm EST
c
2020 Fishmaster All Rights Reserved 2640 Byington Solway Rd, Knoxville, TN 37931 877.777.8693 fishmaster.com
3
DES-183
REV 1.0
Page 4
Step 3: Mounting Legs To Boat
Hardware Needed:
Mark the holes to
1.
know where to drill.
*
Do not apply 3M 5200 adhesive to deck or screw holes until parts 1-2 of
TM
Step 3 is completed to both the front and rear feet.
DRILL IN REVERSE, and
2.
use a 45 degree chamfer
drill bit to prevent gel
coat damage.
Attach leg sections to the
3.
boat by applying 3M 5200
marine adhesive between
and in the holes. Then
screw down the foot.
TM
Step 4: Assembling The Standoffs
Mark to know where
1.
to place the standoff.
4.
Measure standoff and cut with
a fine tooth handsaw to the
appropriate length.
2.
Using a 3/8” drill bit, drill a
hole through the side upright.
Assemble the standoff through the
5.
leg and from the inside of the console.
Place the standoff rod through the
3.
hole and mark where it touches on the
console. Use 14” long 3/8” Drill Bit.
Do you have questions? Call us @ 877.777.8693 Monday – Friday, 8am-5pm EST
c
2020 Fishmaster All Rights Reserved 2640 Byington Solway Rd, Knoxville, TN 37931 877.777.8693 fishmaster.com
4
DES-183
REV 1.0
Page 5
Step 5: Repeat Steps 1-4 For Second Leg
Repeat steps 1-4 to properly assemble
1.
the second leg and mount it to the deck.
Step 1 Step 2
Step 3 Step 4
Step 6: Assemble The Canopy
Hardware Needed:
Insert the double ended canopy
2.
couplers into the inner/outer rails.
1.
*If the coupler is in a colored bag, that is the designated rear coupler.
Install bolts to join the canopy
3.
sections together.
Gather the parts to the canopy.
Remember to install the hinge
4.
bolts.
*
Do you have questions? Call us @ 877.777.8693 Monday – Friday, 8am-5pm EST
c
2020 Fishmaster All Rights Reserved 2640 Byington Solway Rd, Knoxville, TN 37931 877.777.8693 fishmaster.com
5
DES-183
REV 1.0
Page 6
Step 6: Assemble The Canopy (continued)
Install the canopy to the legs by resting
it into the c-clamp and tilting it forward.
PRO TIP: It is recommended
to get assistance in placing the
canopy onto the legs.
Insert the bolts into the c-clamps.
2.1.
Step 7: Attaching the Canvas Top
Slide the canvas top onto the canopy of the tower.
1.
Make sure the white I.D. tag is facing the rear and
on the underside.
Thread the rope through each grommet and over the bars as shown below.
3.
Remove the cable-tie afterwards.
Keep the canvas in place by first attaching cable-
2.
ties. Maintain an even spacing between the canvas
and the tubes.
1
4
2
PRO TIP: With a firm tug,
tighten the canvas down like a
drum head.
3
Do you have questions? Call us @ 877.777.8693 Monday – Friday, 8am-5pm EST
c
2020 Fishmaster All Rights Reserved 2640 Byington Solway Rd, Knoxville, TN 37931 877.777.8693 fishmaster.com
6
DES-183
REV 1.0
Page 7
Final Product
Congratulations,
You have just successfully installed your new Fishmaster Pro Series T-Top!
Send us a picture of your install out on the water to our gallery on Fishmaster.com and we will
send you a FREE t-shirt!
Tag us on social media to be featured on our feed! Welcome to our fishing team!
@fishmasterinc fishmasterinc
Do you have questions? Call us @ 877.777.8693 Monday – Friday, 8am-5pm EST
c
2020 Fishmaster All Rights Reserved 2640 Byington Solway Rd, Knoxville, TN 37931 877.777.8693 fishmaster.com
7
DES-183
REV 1.0
Loading...